Aerpro G183V Dual Lens Brake Light Camera for Ford Transit Custom 2012 to 2015 User Manual
- June 11, 2024
- Aerpro
Table of Contents
Aerpro G183V Dual Lens Brake Light Camera for Ford Transit Custom 2012 to
2015
Product Features
- Image Sensor: 1/3 CMOS
- TV Lines : 700
- Resolution: 976 x 592
- Minimum Illumination: 0.1 Lux (0 Lux when LED is on)
- TV System: NTSC
- Waterproof Rating: IP68
- Horizontal Angle: 80 Degrees
- Vertical Angle: 145 Degrees
- Diagonal Angle: 170 Degrees
- Video Output: 1.0V p-p 75ohm
- Parking Guidelines: Yes (Removable)
- Operating Voltage: 12V DC (Negative Ground)
- Operating Temperature: -20 Degrees C to +70 Degrees C
Disclaimer: Technical knowledge is necessary for installation. Please read the manual prior to installation and use the correct tools to avoid damage to the vehicle or product. Aerpro cannot be held responsible for the installation of this product.
Technical Support: If you encounter any technical issues, please contact Aerpro’s dedicated online technical support centre at aerpro.com/contact.
Product Usage Instructions
- Read the manual prior to installation and ensure you have the necessary technical knowledge and tools.
- Refit the G183V to the vehicle, using the 3M foam pad if needed, taking care not to trap any cables.
- Connect the 7pin of the extension cable to the camera and thread it through the vehicle.
- Attach the Female 7pin connector from the extension to the 7pin to dual 4pin adapter.
- Take the 2x 4pin connections and attach both the 4pin connectors found on the RCA/DC split wire.
- Use both the DC power cables to plug into the black connector and proceed to wire the red to a source of 12V and black to a source of ground.
- Use the RCA adapter to plug into the yellow RCA on the harness, and proceed to plug this into the aftermarket accessory’s video input(s).
- Test the camera connection by turning on the ignition. The rear camera feed should now be visible on screen. Put the vehicle into reverse and the reverse camera feed will automatically populate on screen. If camera feed is unresponsive, please uninstall the wiring and reinstall carefully in accordance with the above steps.
- The camera will be default with parking guidelines. To remove this, simply cut the black loop wire found on the camera’s connector.
If you require further help and support, please contact Aerpro directly at aerpro.com/contact and fill out a support ticket with the full details of your issue.
CONTENTS
- Camera with Male 7pin camera connector
- 10m Female 7pin to Male 7pin extension cable
- 7pin Male aviation connector to 2x Female 4pin connectors (1x Yellow, 1x Black)
- 2x 4pin Male aviation connectors to 2x Female RCA’s (1x Yellow, 1x Black)
- 2x DC power cables with Male DC connector to bare wires
- 2x Male to Male RCA adapters
- 3M camera shaped foam pad
- Instructions
INSTALLATION
-
Remove the third brake light from the vehicle and unplug the connection cable.
-
Refit the G183V (if needed, with the use of the 3M foam pad) to the vehicle, taking care not to trap any cables.
-
Connect the 7pin of the extension cable to the camera and thread through the vehicle
-
Attach the Female 7pin connector from the extension to the 7pin to dual 4pin adapter.
-
Take the 2x 4pin connections and attach both the 4pin connectors found on the RCA/DC split wire.
-
Use both the DC power cables to plug into the black connector and proceed to wire the red to a source of 12V and black to a source of ground.
-
Use the RCA adpater to plug into the yellow RCA on the harness, and proceed to plug this into the aftermarket accessory’s video input(s).
-
Test the camera connection by turning on the ignition. The rear camera feed should now be visible on screen. Put the vehicle into reverse and the reverse camera feed will automatically populate on screen.
If camera feed is unresponsive, please uninstall the wiring and reinstall carefully in accordance with the above steps. -
The camera will be default with parking guidelines. To remove this, simply cut the black loop wire found on the camera’s connector.
For further help and support, please contact us directly at aerpro.com/contactand fill out a support ticket with the full details of your issue.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>