VIDEX VLE-DLRS-124 LED Surface Downlight Fixture Instruction Manual
- June 9, 2024
- VIDEX
Table of Contents
VLE-DLRS-124 LED Surface Downlight Fixture
Instruction Manual
LED SURFACE DUMONT FIXTURE
-
Rated voltage, frequency.
-
Rated power.
-
Rated luminous flux.
31. Luminous flux of luminaries.
3.2. Luminous flux of light source (3601.
3.3. This product contains a light source of energy efficiency class. -
Color temperature.
-
Not compatible with lighting dimmer.
-
Color Rendering Index.
-
Beam angle of luminaries.
-
Nominal lifetime.
-
Protection against solid foreign objects bigger than 12mm provided.
-
ON/OFF cycles.
-
No perceptible flicker to the human eye.
-
Ultraviolet-free.
-
Mercury-free.
-
Compliance with standards of ecodesign and energy labeling in force from Sep 01. 2021.
-
Working temperature.
-
Product meets requirements of EU directives.
-
The minimum distance from the illuminated object.
-
Class II. Protection against electric shock is provided not only through basic insulation, but also double or reinforced insulation.
-
Product can be installed and operated in/on a surface made of materials which are normally flammable.
-
Replace the defective lamp cover immediately. Don’t use the product if the outer bulb is cracked or broken.
-
For indoor use only.
-
LED light source can be replaceable by the manufacturer’s authorized person.
-
The control gear can be replaceable by the manufacturer’s authorized person.
ENVIRONMENTAL PROTECTION -
Pursuant to the provisions of the WEEE Act, it is forbidden to put waste equipment marked with the symbol of a crossed bin together with other waste. The user, wishing to get rid of electronic and electrical equipment, is obliged to return it to a waste equipment collection point. There are no hazardous components in the equipment that have a particularly negative impact on the environment and human health.
PRODUCT’S PURPOSE AND APPLICATION
This product is intended for general lighting in a home space as well as other indoor spaces.
INSTALLATION INSTRUCTIONS
Installation must be performed by an electrician or authorized person. Read the user’s manual prior installation. The light source and control gear are an integral unit. Individual elements cannot work separately. Any assembly or maintenance activities to be done with power supply off. To install the LED fixture:
- Drill the holes on the ceiling and fix the bracket with the screws (Fig1).
- Connect the L,N wires to the – 230V, 50 / 60Hz mains using a screw terminal (Fig.2). The ends of the wires must be insulated to the appropriate length.
- Connect the LED luminaire with the connector of control gear (Fig.3.)
Install the light fixture on the bracket and fix it with screw at both sides (Fig.4). Before the first use it is necessary to verify that mechanical installation and electric connection are carried out correctly.
FUNCTIONAL CHARACTERISTICS
This product should be used indoor only.
MAINTENANCE & SAFETY INSTRUCTIONS
Any maintenance work must be performed when the power supply is cut off and
the product has cooled down. Clean only with soft and dry cloths. Do not use
chemical detergents. Do not cover the product. Ensure free air access. LED
fixture may heat up to a higher temperature. Product can only be supplied by
rated voltage or voltage within the range provided. It’s forbidden to use the
product with the damaged electric wiring or places of connections. ATTENTION!
Do not look directly at LED light beam. It’s forbidden to use the product with
damaged cover. Product must not be used in unfavorable conditions, e.g. dust,
water, moisture, vibrations, explosive air atmosphere, fumes, or chemical
fumes, etc. The light source and control gear in the LED luminaire shall only
be replaced by the manufacturer or his authorized service agent. If the
product is damaged, contact the manufacturer for service. Used or damaged
luminaire should be disposed of in accordance with applicable regulations.
Failure to follow these instructions may result in e.g. fire, burns,
electrical shock, physical injury and other material and non-material damage.
Allegro Opt Sp. z o. o. shall not be responsible for any damage resulting from
the failure to follow these instructions. The manufacturer reserves the right
to make changes in the manual.
Not included
Allegro Opt Sp. z o.o., Handlowa 23, 05-120 Legionowo, Poland.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>