Shenzhen Sunveytech SWD-VK-TB703+607 Wireless Backup Camera User Manual

Sunveytech SWD-VK-TB703+607 Wireless Backup Camera
User Manual

What’s in the Box?

NOTE: The contents included may be different based on the kit you purchased. Please take the actual product as standard.

Introduction

Please read all of the installation instructions carefully before installing the product. Improper installation will void the manufacturer’s warranty.

Thank you very much for purchasing a Rear View Backup Camera System. With this manual, you will be able to properly install and operate the unit.
The Backup Camera System is intended to be installed as a supplement aid to your standard rearview mirror that already exists in your vehicle. The Backup Camera System should not be used as a substitute for the standard rearview mirror or for any other mirror that exists in your vehicle. In some jurisdictions, it is unlawful for a person to drive a motor vehicle equipped with a TV viewer or screen located forward of the back of the driver’s seat or in any location that is visible, directly or indirectly, to the driver while operating the vehicle.

Monitor Operation

1. Use this button to turn the monitor On and Off
2. Switch channel
3. 1). Enter the menu and move to the left 2). After the car ruler is turned on, adjust the car ruler
4. MENU
5. 1). Enter the menu and move to the right 2). After the car ruler is turned on, select the mode M/W/H
6. 1). Enter 2). Keep SD Card, Start /Stop Recording
7. Car ruler

Open the SD card slot on the monitor back with a screwdriver, insert the SD card It is recommended to use a high-speed TF card of class 10 or above. (Less than 256G) Plugin the card to start recording(“ENTER” to turn on/off recording)
• REC

Sector bracket installation method

installation Diagram

Monitor Installation
Choose a monitor location in your vehicle that does not block your view and complies with local laws for safe driving. Do not place in an area where it might interfere with driving.

Camera Installation
Suitable Installation Position 

Connection method

Note: Of connecting power directly to the battery, the cameras are always ON and therefore can drain the battery. Therefore it is recommended to connect power to an ignition switched accessory power source.

Pairing the Camera and Monitor

NOTE: when you need pairing, please confirm the circuit is properly connected and powered. If you need to pair multiple cameras, please switch to the corresponding channel.

Specifications

CAMERA
Image Sensor| 1/3 inch
Waterproof Rating| IP68
View Angle| 127′[H] 170 [DJ
Camera Pixel| 1000TVL
MONITOR
LCD Size| 7 inch IPS
Resolution| 1024(H) x 600(V)
Contrast| 500.1
Brightness| 600cd/m
Response Time| 25ms
Power Consumption| <500mA

Troubleshooting

Check the fuse in the Cigarette socket adapter
Camera and Monitor won’t pair| Check if the camera is receiving power
Make sure to follow the instructions to operate the Pairing
Weak Signal| Check if the camera and monitor antennas are installed
Distance between camera and monitor is too great. Reduce the distance between camera and monitor
Large dense objects could be obscuring the signal. If possible, move the objects
Interference from overhearing power lines may be affecting the signal
Try unpairing and pairing
Night Vision is poor| The night sensor on the camera may be dirty or obstructed
Ensure the camera is installed at least 2 inches away from rear lights
Dark Picture| Check whether brightness and contrast are adjusted correctly

FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be  determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>