CENTEK CT-1840-50 Kitchen Range Hood Instruction Manual

CENTEK CT-1840-50 Kitchen Range Hood

DEAR CUSTOMER!
Prior to operating the appliance, please carefully read the present manual which contains important information regarding its proper and safe operation. Take care not to lose the present manual. The manufacturer will not be responsible for any damage resulting from improper use of the appliance or from non-observance of the instruc-tions and provisions of the present manual, as well as from attempts by unskilled persons at repairing the appliance. Should You decide to transfer the appliance to another person, please pass the present manual over along with it.
The hood is a household appliance and is not intended for industrial use!

PURPOSE OF THE APPLIANCE

For air filtering from grease, burns and other impurities, formed during the heat treatment of products.

SECURITY MEASURES

In order to avoid situations that are dangerous to life and health, as well as premature failure of the device, it is necessary to strictly observe the following conditions:

• Read this manual carefully before putting the device into oper-ation.
• Keep this manual.
• Make sure that the voltage indicated on the device corresponds to the voltage in the power supply network. Do not use adapters to avoid fire.
• It is forbidden to use accessories and spare parts from other manufacturers. If such parts are used, the manufacturer’s warranty is void. Replacement of lamps with lamps of other manufacturers is allowed, provided that the installed lamps will not differ in type, form factor, or dimensions and will not exceed the power of the original lamps installed by the manufacturer.
• Do not use the appliance if the power cord, plug and other parts of the appliance are damaged.
• If the power cord is damaged, its replacement, in order to avoid danger, must be carried out by the manufacturer, the service department or similar qualified personnel.
• During the first use, a slight unpleasant odor may appear (which will disappear after several uses), which is explained by the possible presence of residues of oils and other substances on the internal surfaces.
• The device must be installed so that its lower surface is at least 65 cm from the heating plane of the electric furnace or 75 cm from the heating plane of the gas furnace.
• Be careful when working simultaneously with the hood and burner (hearth). The hood sucks in air along with oxygen, which is needed for the Gorenje process.
• The negative pressure in the room should not exceed 4Pa (4×10-5 bar). For reliable and safe operation, ventilation of the room should be provided.
• Do not check the condition of the filters while the device is running.
• Do not touch the lamp or adjacent areas during the operation of the lighting system or immediately after it is turned off.
• To avoid overloading the power supply, do not use this device at the same time with energy-intensive devices.
• The device is not intended for use by persons (including children) with reduced physical, sensory or mental abilities or lack of life experience or knowledge, unless they are supervised or instructed to use the device by a person responsible for their safety. Children should be supervised to prevent playing with the device.
• If smoke appears, turn off the appliance immediately and disconnect it from the mains.
• It is forbidden to cook dishes on an open flame under the appli-ance. Avoid an open flame, as it damages the filters and can lead to a fire. Do not allow a flare flame to appear under the appliance. The flame of the burners should always be covered with dishes.
• Do not use the appliance outdoors.
• BE CAREFUL! The surface of the device may heat up during its op-eration.
• If the connecting pipe consists of two or more parts, then the upper part should be located on top of the lower part. Do not connect the discharge from the appliance to the hot air circulation channel or to the channel used to remove smoke from devices powered by energy other than electrical.
• Before starting to assemble the device, disconnect the grease filter to facilitate its installation.
• If there is no plug on the cable, install a plug designed to work with the load indicated on the characteristics table. If the device is equipped with a plug, then install the device in such a way that the plug is accessible.
• In the case of direct connection to the power grid, a multi-pole switch with a contact gap of at least 3 mm, designed for the desired load and meeting current standards, must be placed between the device and the network.

TECHNICAL SPECIFICATION

SCOPE OF SUPPLY AND APPLIANCE DESCRIPTION

• Hood – 1 pc.
• Anti-fat aluminum filter – 2 pcs.
• Lamp – 1 pc.
• Plastic anchor – 6 pcs.
• Self-tapping screw for wall mounting – 6 pcs.
• Check valve lobe – 2 pcs.
• User Manual – 1 pc.
  The appliance includes plastic flaps for the backflow valve. These shall be installed in the air duct grooves at the last moment upon installation completion.

WORKING PROCEDURE

Before installing the hood, make sure that:

• the distance from the bottom surface of the hood is at least 65 cm from the heating plane of the electric oven or 75 cm from the heating plane of the gas oven;
• the length of the electric cord is enough to connect the hood to the mains;
•  nothing will damage the electric cord during the further oper-ation;
• there is a possibility of air outlet equipment.
  Before starting to assemble the device, disconnect the grease filter to facilitate its installation. The hood removes the smoke into the atmosphere through the outer wall of the building or through an existing ventilation shaft. For this purpose, it is necessary to purchase a sliding non-flammable chimney pipe, that corresponds to the current regulations, and connect it with a flange. The hood can be mounted in several ways.

MOUNTING THE HOOD TO THE WALL

Measure the distance on the wall for mounting the hood. Drill two holes with a diameter of 8 mm, as shown in picture 1. Make sure that the anchors and screws, which are included in the delivery package, are suitable for the type of wall on which the hood will be mounted. Install the anchors, and tighten the screws. Remove the protective film from the hood, then install the hood on the screws.
There are 2 holes with a diameter of 6 mm on the back panel of the hood. Fix the hood to the wall with protective screws, using these holes. Install the air duct valve petals on the top of the hood. Install the backflow valve flaps on the top of the exhaust hood.

MOUNTING THE HOOD UNDER AN OVERHEAD CABINET
ATTENTION! You will have to drill an air duct opening in the cabinet bottom. The second opening can be made either in the top side or in the back side of the cabinet, depending on how the air exhaust is arranged. You may use any type of dust tubing, both flexible and rigid, for air exhaust through the cabinet.
Measure and mark the distances required for exhaust hood mounting on the cabinet bottom.
Drill four 4-mm holes a shown in Figure 2. Install the backflow valve flaps on the top of the exhaust hood. Remove the protective film from the exhaust hood and screw the hood to the cabinet.

MOUNTING THE HOOD INSIDE AN OVERHEAD CABINET
ATTENTION! You will have to drill an air duct opening in the shelf inside the cabinet. The second opening can be made either in the top side or in the back side of the cabinet, depending on how the air exhaust is arranged. You may use any type of dust tubing, both flexible and rigid, for air exhaust through the cabinet.
Use the mounting template in order to exactly cut the openings in the shelf required for the hood itself, the air duct and the power cable. In this case the exhaust hood is mounted in the same way as when the hood is installed under the cabinet, except that the parts are screwed to a shelf inside the cabinet instead of the cabinet bottom. Measure the distances required for hood installation on the cabinet shelf. Note that the back side of the exhaust hood should under no circumstances touch the back wall of the cabinet.

There should be a minimum distance of 10 cm between the back side of the hood and the back wall of the cabinet.
Drill four 6-mm holes into the cabinet shelf. Install the backflow valve flaps on the top of the hood. Remove the protective film from the hood and screw it to the cabinet. The exhaust hood can also be mounted on the shelf guide rails inside the cabinet, but such installation methods may require the intervention of a furniture assembly technician and the purchase of additional materials.

MOUNTING THE HOOD INSIDE AN OVERHEAD CABINET
ATTENTION! You will have to drill an air duct opening in the shelf inside the cabinet. The second opening can be made either in the top side or in the back side of the cabinet, depending on how the air exhaust is arranged. You may use any type of dust tubing, both flexible and rigid, for air exhaust through the cabinet.
Use the mounting template in order to exactly cut the openings in the shelf required for the hood itself, the air duct and the power cable. In this case the exhaust hood is mounted in the same way as when the hood is installed under the cabinet, except that the parts are screwed to a shelf inside the cabinet instead of the cabinet bottom. Measure the distances required for hood installation on the cabinet shelf.

Note that the back side of the exhaust hood should under no circumstances touch the back wall of the cabinet. There should be a minimum distance of 10 cm between the back side of the hood and the back wall of the cabinet.
Drill four 6-mm holes into the cabinet shelf. Install the backflow valve flaps on the top of the hood. Remove the protective film from the hood and screw it to the cabinet. The exhaust hood can also be mounted on the shelf guide rails inside the cabinet, but such installation method may require an intervention of a furniture assembly technician and the purchase of additional materials.

5. CARE OF THE DEVICE
Disconnect the power cord from the mains and allow the engine to cool down. Remove the anti-fat aluminum filters. Rinse them in warm soapy water, then dry them and put them in the hood. This procedure should be performed at least once a month. A filter contaminated with grease is:

• Risk of fire. Oil stuck on the filter is flammable and can cause a fire.
• Decrease in the efficiency of air drainage.
• Risk of failure of the device. Contaminated filters do not provide sufficient air conductivity, which can cause engine overload.

Wash the hood regularly, removing all food residues, fat and other contaminants. Wipe the outer surface only with a damp soft cloth with the addition of detergent.
Storage and operation of the hood should be carried out in dry heated rooms at a temperature not lower than + 5 °C and a relative humidity of not more than 80%.
Transportation of the product should be carried out in accordance with the marking indicated on the package. After transporting the hood in conditions of low temperature, it is allowed to use the device only after two hours of its stay in a warm room.
We apologize if the scope of delivery, dimensions, description, technical characteristics, appearance or color of the product turned out to be inaccurate. The manufacturer reserves the right to change these parameters without prior notice, as a result of which, at the time of purchase of a particular product, they may differ from those indicated earlier.

POSSIBLE PROBLEMS AND WAYS TO FIX THEM

• Before contacting the service center, check the following: Make sure that the hood is connected to the mains. Check the mains voltage.
• By external inspection, check the integrity of the elements of the electrical circuit, in case of malfunction of any element, contact customer service.
  Repairs should only be carried out by qualified service center personnel! If your lamp has burned out, you can replace it yourself. To do this, follow these steps:

1. Turn off the appliance and disconnect it from the mains.
2. Remove the lamp cover by unscrewing the 2 screws.
3. Remove the lamp.
4. Replace the lamp with a new one with a base of the same standard.
5. Assemble everything in reverse order.

INSTRUCTION MANUAL

By CENTER

1. This range hood model is available in two variants:
   CT-1840-50 and CT-1840-60

• 220-240V ~50/60Hz

Product dimensions:

• CT-1840-50: (W x D x H) 495 x 300 x 225mm
• CT-1840-60: (W x D x H) 595 x 300 x 225mm

Installation Instructions:

• Connect the range hood to a power source using the provided cable
• Mount the range hood on the wall, ensuring it is level and secure
• Connect the range hood to a vent pipe using the provided ducting
• Ensure the range hood is properly aligned with the cooking surface below it
• Refer to the user manual for further instructions

Safety Instructions:

• The range hood must be installed by a qualified technician
• Do not use the range hood without properly connecting it to a vent pipe
• Do not touch the range hood while it is in operation as it may be hot
• Keep the range hood and its components away from water and other liquids

Maintenance Instructions:

• Clean the range hood regularly with a damp cloth and mild detergent
• Replace the filter every six months or as necessary
• Inspect the ducting and vent pipes regularly for signs of damage or blockages

Contact Information:

• For technical support or customer service, please contact CENTER at 350912
• For additional information, visit our website at www.centek.com

To use the CT-1840 range hood, follow these instructions:

1. Ensure that the range hood is connected to a power source and properly mounted on the wall
2. Connect the range hood to a vent pipe using the provided ducting
3. Adjust the range hood so that it is properly aligned with the cooking surface below it
4. Turn on the range hood using the control panel
5. To clean the range hood, use a damp cloth and mild detergent. Replace the filter every six months or as necessary.

Please refer to the user manual for further instructions on installation, safety, and maintenance.

DISPOSAL
Upon expiry of its service life the appliance can be disposed of separately from ordinary domestic waste. You can turn it over to a specialized electric and electronic appliance disposal and recycling center.

CERTIFICATION DATA, GUARANTEE

The service life of this item is 8 years since the date of sale to the end user, provided the item will be used in strict accordance with the present manual and the applicable technical standards. Upon expiry of the service life please contact the nearest authorized service center for suggestions as to further operation of the appliance. The manufacturing date of the appliance is integrated into the serial number (digits 2 and 3 – year, digits 4 and 5 – month of manufacture). If any questions related to appliance maintenance should arise, or if the appliance has malfunctions, apply to the CENTEK TM Authorized Service Center. The address of the service center can be found on the website https://centek.ru/servis. Service support contacts: Phone: +7 (988) 24-00-178, VK: vk.com/centek_krd. General Service Center: OOO “Larina- Servis”, Krasnodar, Phone: +7 (861) 991-05-42.
The product has the Certificate of Conformity No.
ЕАЭС RU C-CN.ВЕ02.В.03401/21 of 26.01.2021.

INFORMATION ABOUT THE MANUFACTURER, IMPORTER
I moved to EAEU by: Individuality Predprini-metal Asrumyan Karo Shurikovich. Address: Russia, 350912, Krasnodar, ul. Atamana Lysenko, 23, pgt. Pashkovskiy. Phone: +7 (861) 2-600-900.

DEAR CONSUMER!
The guarantee period for all appliances amounts to 36 months from the date of sale to the end consumer. With this Warranty Card the Manufacturer confirms the proper condition of the appliance and undertakes to repair, free of charge, all defects caused by the Manufacturer’s default.

GUARANTEE MAINTENANCE TERMS

1. The guarantee shall be valid if the following documentation con-ditions are observed:

   • The original Warranty Card shall be filled out correctly and clearly, indicating the of appliance model, serial number and sale date, the stamp of the seller company and signature of its representative shall be available, as well as the stamps on each coupon and the buyer’s signature in the Warranty Card.
   • The Manufacturer reserves the right to reject guarantee maintenance if the buyer fails to provide the abovementioned documents or if the information contained therein is incomplete, illegible or ambiguous.

2. The guarantee shall be valid if the following operation conditions are observed:

   • the appliance is used in strict accordance with the present manual;
   • the safety rules and requirements are observed.

3. The guarantee does not apply to regular maintenance, cleaning, installation and setup of the appliance at the owner’s location.

4. The guarantee does not apply in the following cases:

   • mechanical damage;

   • normal wear of the appliance;

   • non-observance of operation requirements or erroneous actions on the part of the user;

   • improper installation or transportation;

   • natural disasters (lightning, fire, flood, etc.), as well as any other causes beyond the Manufacturer’s or Seller’s control;

   • ingress of foreign objects, liquids or insects into the inside of the appliance;

   • repairs or modifications to the appliance by unauthorized persons;

   • use of the appliance for commercial purposes (loads exceeding normal domestic application), the connection of the appliance to utility and telecommunication networks incompliant with national technical standards;

   • failure of the following accessories, if replacement of these is al-lowed by design and does not involve disassembly of the appliance:
     a) remote control units, rechargeable batteries, replaceable batteries (power cells), external power supply units and chargers;
     b) consumables and accessories (packaging, covers, slings, carry bags, mesh screens, blades, flasks, plates, supports, grilles, spits, hos-es, tubes, brushes, nozzles, dust collectors, filters, smell absorbers);  for battery- powered appliances – operation with inappropriate or depleted batteries;

   • for rechargeable battery-powered appliances – any damage caused by improper battery charging and recharging.

5. The present guarantee is provided by the Manufacturer in addition to the consumer rights determined by the applicable legislation and does not limit these rights in any way.

6. The Manufacturer shall not be made liable for possible damage, directly or indirectly inflicted by CENTEK brand products on people, domestic animals, the consumer’s or third persons’ property if such damage is inflicted as the result of non-observance of appliance installation and operation requirements, deliberate or negligent actions (omission) by the consumer or third persons, as well as of force majeure circumstances.

7. Service centers will only accept appliances in a clean state (there should be no food residues, dust and other contamination on the appliance).
   The Manufacturer reserves the right to change the design and specifications of the appliance without prior notice.

References

• Сервис - Официальный сайт Centek
• VK.com | VK
• Сервис - Официальный сайт Centek

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>