ZUG AdorinaWash V400 Washing Machine Installation Guide
- June 9, 2024
- ZUG
Table of Contents
AdorinaWash V400 Washing Machine
Installation Guide
Installation
| Your washing machine automatically detects the amount of laundry placed
inside when selecting a program.
While installing the product, before the first use, calibration should be done
to ensure that the laundry amount is detected in the most accurate way.
To do this, select the Drum Cleaning program and cancel the spin function.
Start the program without laundry.
Wait for the program to finish, which will take about 15 minutes.
The program name may vary depending on the model. For the appropriate program selection, review the program descriptions section.
---|---
- Apply to the nearest authorized service agent for the installation of your product.
- Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer’s responsibility.
- Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.
- Make sure that the installation and electrical connections of the product are performed by authorized service. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.
- Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.
1.1 Appropriate installation location
- Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other similar surfaces.
- When the washing machine and drier are placed on top of each other, their total weight –when loaded– amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!
- Do not place the product on the power cable.
- Do not install the product in the environments where the temperature falls below 0 ºC.
- Leave a minimum space of 1 cm between the machine and the furniture.
- On a graduated floor, do not place the product next to the edge or on a platform.
1.2 Removing the transportation locks
- Loose all bolts with an appropriate wrench until they turn freely.
- Remove the transport safety bolts by turning them slightly.
- Insert the plastic covers in the bag containing the user manual to the openings on the rear panel.
| CAUTION: Remove the transportation safety bolts before operating the
washing machine! Otherwise, the product will be damaged.
---|---
| Keep the transportation safety bolts in a safe place to reuse when the
washing machine needs to be moved again in the future.
Install the transport safety bolts in reverse order of the disassembly
procedure.
Never move the product without the transportation safety bolts properly fixed
in place!
1.3 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging reinforcement. Remove the
packaging reinforcement by pulling the ribbon. Do not make this operation
alone by yourself.
1.4 Connecting water supply
| The water supply pressure required to run the product is between 1 to 10
bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters of water flowing
from the fully open tap in one minute to have your machine run smoothly.
Attach a pressure reducing valve if water pressure is higher.
---|---
If you are going to use the double water-inlet product as a single (cold)
water-inlet unit, you must install the supplied stopper to the hot water valve
before operating the product. (Applies for the products supplied with a blind
stopper group.)
| CAUTION: Models with a single water inlet should not be connected to
the hot water tap. In such a case the laundry will get damaged or the product
will switch to protection mode and will not operate.
CAUTION: Do not use old or used water inlet hoses on the new product. It
may cause stains on your laundry.
Connect the special water supply hoses supplied with the product to the water
inlets on the product. Red hose (left) (max. 90 ºC) is for hot water inlet,
blue hose (right) (max. 25 ºC) is for cold water inlet.
Make sure that the hot and cold water taps are connected correctly when the
product is being installed. Otherwise, your laundry will come out hot at the
end of the washing process and wear out.
- Tighten the nuts of the hose by hand. Never use a tool when tightening the nuts.
- When hose connection is completed, check whether there is leak problems at the connection points by opening the taps fully. If any leaks occur, turn off the tap and remove the nut. Re tighten the nut carefully after checking the seal. In order to prevent the water leaks and resultant damages, keep the taps closed when you do not use the product.
1.5 Connecting the drain hose to the drain
- Attach the end of the drain hose directly to waste water drain, lavatory or bathtub.
| CAUTION: Your drain house will be flooded if the hose comes out of its
housing during water discharge. Moreover, there is risk of scalding due to
high washing temperatures! In order to prevent such situations and make sure
that the machine performs water intake and discharge processes without any
problem, fix the drain hose securely.
---|---
- Connect the drain hose to a minimum height of 40 cm and a maximum height of 100 cm.
- In case the drain hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure.
- To prevent the waste water to go back into the machine again and to ensure easy drainage, do not immerse the end of the hose into the waste water or do not insert it into the drain for more than 15 cm. If it is too long, cut it short.
- The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.
- If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.
1.6 Adjusting the feet
| CAUTION: In order to ensure that the product operates more silently and
vibration-free, it must stand level and balanced on its feet. Balance the
machine by adjusting the feet. Otherwise, the product may move from its place
and cause crushing and vibration problems.
CAUTION: Do not use any tools to loosen the lock nuts. Otherwise, they
will get damaged.
---|---
- Loosen the lock nuts on the feet by hand.
- Adjust the feet until the product stands in a stable and balanced way.
- Tighten all lock nuts by hand again.
1.7 Electrical connection
Connect the product to a grounded outlet protected by a 10 A fuse. Our company
shall not be liable for any damages that will arise when the product is used
without grounding in accordance with the local regulations.
- Connection must comply with national regulations.
- Power cable plug must be within easy reach after installation.
- If the current value of the fuse or breaker in the house is less than 10 Amps, have a qualified electrician install a 10 Amp fuse.
- The voltage specified in the “Technical specifications” section must be equal to your mains voltage.
- Do not make connections via extension cables or multi-plugs.
CAUTION: Damaged power cables must be replaced by the Authorized Service Agents.
V-ZUG
AG, Industriestrasse 66, CH-6302 Zug
Tel. +41 58 767 67 67
Fax +41 58 767 61 61
[email protected]
www.vzug.com
Service-Center: Tel. 0800 850 850
Document Number
2820530669_EN / 20-03-23.(13:56)