seeed studio MT7688 NG96 Module Instruction Manual
- June 9, 2024
- seeed studio
Table of Contents
Instruction manual of MT7688
BG96 module
BG96MC-128-SGNS
Overview
The functions of BG96-MT7688 model are WIFI、cellular、GPS. The detail image as Figure1.
Hardware connection
The use of BG96 module depends on the Main board and DVI board. Assemble as shown in Figure2.
Binding pairing
Using bind MT7688 with mainboard.
Instruction for 7688
Linking PC with 7688 first.
Open network assistant NetAssist_v4.3.25.
protocol type:Tcp Client
Host address:192.168.12.10
Port:4444
AT test command:
{“cmd”:”at”,”payload”:{“atcmd”:”AT+CIMI”,”timeout_ms”:300}} #Read SIM
{“cmd”:”at”,”payload”:{“atcmd”:”AT+CSQ”,”timeout_ms”:300}} #Acquired signal
quality
{“cmd”:”at”,”payload”:{“atcmd”:”AT+CREG?”,”timeout_ms”:300}} #Obtain the
network registration status
{“cmd”:”at”,”payload”:{“atcmd”:”AT+QGPS=1″,”timeout_ms”:300}} #Open GPS
{“cmd”:”at”,”payload”:{“atcmd”:”AT+QGPS?”,”timeout_ms”:300}}
Query GPS open or not
{“cmd”:”at”,”payload”:{“atcmd”:”AT+QGPSLOC?”,”timeout_ms”:300}} #Acquired GPS
data
{“cmd”:”at”,”payload”:{“atcmd”:”AT+QGPSEND”,”timeout_ms”:300}} #Close GPS
F/W Update
- Use your PC to connect the Guardian-xxxx Wi-Fi (password CMIIC@123) and open the link ( http://192.168.12.10 from a Browser (root passcode 12345678))
- Select System–>Backup/Flash Firmware:
- Check Keep settings checkbox,click file button as below:
- Select mt7688 firmware and click open button as blew。
- Click Flash image button。
- Click the Flash image button,wait the updating for a few minutes.
- Please don’t power down and close the browser during updating.
- You will see PC Wi-Fi is disconnected after updating and rebooting. A few minutes later, you can reconnect Guardian-xxxx Wi-Fi, if you can see login page in browser, the upgrade is successfully performed.
FCC STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body
Room 332, building 2, innovation center,
science and Innovation Park, Mianyang, Sichuan, China
Documents / Resources
|
seeed studio MT7688 NG96
Module
[pdf] Instruction Manual
BG96-MT7688-A, BG96MC-128-SGNS, MT7688 NG96 Module, MT7688, MT7688 Module,
NG96 Module, NG96, Module, BG96MC-128-SGNS
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>