TECNO Phantom X2Pro 5G Smartphone User Manual
- June 9, 2024
- TECNO
Table of Contents
hantom X2Pro 5G Smartphone
User Manual
Phantom X2Pro 5G Smartphone
Explosion diagram specification
| 1 | LCD&CTP_MODULE | 2 | MIDDLE_FRAME_HEAT_FILM |
|---|---|---|---|
| 3 | VC_THERMAL | 4 | MIDDLE_FRAME |
| 5 | PROTECT_FILM_VC | 6 | FRONT_CAMERA_FRAME |
| 7 | REAR_CAMERA_CONDUCTIVE_F OAM_MAIN_50M | 8 | PL_SENSOR_SILICA_RUBBER |
| 9 | MB | 10 | REAR_CAMERA_CONDUCTIVE_C OPPER_FOIL_MAIN_50M |
| 11 | REAR_CAMERA_CONDUCTIVE_C OPPER_FOIL_SUB_50M | 12 | FRONT_CAMERA |
| 13 | REAR_CAMERA_MAIN_50M | 14 | REAR_CAMERA_SUB_50M |
| 15 | REAR_CAMERA_13M | 16 | RECEIVER_MODULE |
| 17 | FLASH_LED_CONDUCTIVE_FOAM | 18 | RFPA_SHIELDING_HEAT_FILM |
| 19 | FRONT_CAMERA_SEAL_FOAM | 20 | CHG_SHIELDING_COPPER_FOIL |
| 21 | PAI_SHIELDING_COPPER_FOIL | 22 | RECEIVER_CONDUCTIVE_FABRIC |
| 23 | REAR_CAMERA_CONDUCTIVE_C OPPER_FOIL_13M | 24 | REAR_CAMERA_CONDUCTIVE_F |
OAM_13M
25| FRONT_CAMERACONDUCTIVE COPPER_FOIL| 26| REAR_CAMERA_BTB_LMMP_FOA M_13M
27| REAR_CAMERA_BTB_CONDUCTI VE_FABRIC| 28| WCN_SHIELDING_COPPER_FOIL
29| PA2_SHIELDING_COPPER_FOIL| 30| NFC
31| REAR_CAMERA_DECO_CONDUCT IVE_FOAM| 32| FPC_REAR_FLASH
33| FPC_RECEIVER| 34| UP_HOUSING
35| SCREW_M1.4L2.5D2.5H0.5| 36| SCREW_M1.4L3.5D2.5H0.5
37| REAR_CAMERA_DECO| 38| REAR_FLASH_LENS
39| REAR_CAMERA_LENS_13M| 40| REAR_CAMERA_LENS_SUB_50M
---|---|---|---
41| BATTERY_COVER| 42| BATTERY
43| COAXIAL_CABLE_CONDUCTIVE_F ABRIC| 44| SPEAKER_BOX
45| COAXIAL_CABLE_BLACK| 46| LCD_BTB_LMMP_CONDUCTIVE_F OAM
47| GND_BTB_LMMP_CONDUCTIVE_FOAM| 48| MOTOR_LMMP_FOAM
49| FPC_MAIN_BTB_LMMP_FOAM| 50| COAXIAL_CABLE_WHITE
51| FPC_RUBBER| 52| PMU_SHIELDING_HEAT_FILM
53| FPC_LCD| 54| SIM_CARD_HOLDER
55| FPC_MAIN| 56| SUB_BOARD_SIM
57| USB_RUBBER| 58| SUB_BOARD_USB
59| SIDEKEY_FRAME| 60| FPC_SIDEKEY
61| SUB_BOARD_ANT| 62| MOTOR
63| SIDEKEY_POWER| 64| SIDEKEY_VOL
65| FINGER_MODULE| 66| SIDEKEY_METAL_STEEL
Know your phone
- Front camera
- Volume + key
- Volume – key
- Power key
- NFC
SIM/SD card installation
- Power off mobile.
- Refer to the following picture for SIM / SD card installation.
Charging the phone
You can charge your device using a charger or by connecting it to the computer
using a USB cable (comes with the phone).
Use only TECNO charger and cables. Other chargers or cables may damage the
device. This will invalidate your phone warranty.
FCC Caution
Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Information to user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6
W/kg averaged over one gram of tissue. Device types: AD9 (FCC ID: 2ADYY-AD9)
has also been tested against this SAR limit. The highest SAR value reported
under this standard during product certification for use at the ear is
0.781W/kg and when properly worn on the body is 0.321W/kg. This device was
tested for typical body-worn operations with the back of the handset kept 10
mm from the body. To maintain compliance with FCC RF exposure requirements,
use accessories that maintain a 10 mm separation distance between the user’s
body and the back of the handset. The use of belt clips, holsters and similar
accessories should not contain metallic components in its assembly. The use of
accessories that does not satisfy these requirements may not comply with FCC
RF exposure requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
HiOS runs on Android™ OS.
Android is a trademark of Google LLC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>