TECNO KJ6S SPARK 20 Pro Smart Phone User Manual
- June 1, 2024
- TECNO
Table of Contents
TECNO KJ6S SPARK 20 Pro Smart Phone
Product Specifications
- Model: KJ6s
- Operating System: HiOS (based on Android OS)
- FCC ID: 2ADYY-KJ6S
- SAR Value: 0.745 W/kg (ear), 0.668 W/kg (body)
Product Usage Instructions
Know Your Phone
- Front camera
- Volume + key
- Volume – key
- Power key & side fingerprint sensor
- NFC
SIM/SD Card Installation
- Power off the mobile.
- Refer to the picture provided for SIM/SD card installation.
Charging the Phone
You can charge your device using a charger or by connecting itto the computer using a USB cable (included with the phone).
Important: Use only TECNO charger and cables. Other chargers or cables may damage the device and void your phone warranty.
Explosion diagram specification
1 | CTP+LCM | 2 | FRONT COVER FRAME |
---|---|---|---|
3 | CARD HOLDER | 4 | PCBA MB |
5 | MAIN WATERPROOF FRAME | 6 | RCAM LOCATION FRAME ASM |
7 | REC | 8 | LT SENSOR RUBBER |
9 | FPC MAIN | 10 | FINGERPRINT |
11 | CAM FF RUBBER | 12 | MID HOUSING |
13 | SCREW L3.5 | 14 | REC DECO PART |
15 | BAT COVER ASM | 16 | DECO |
17 | CAM LENS 1 | 18 | CAM LENS 2 |
19 | CAM LENS 3 | 20 | R CAM CON COPPER |
21 | RAD FILM MB SHIELD | 22 | MYLAR |
23 | CAM 108M DECO | 24 | CAM 8W DECO |
25 | CAM 2M DECO | 26 | RUBBER USB |
27 | RUBBER EARPHONE | 28 | NFC |
29 | PCBA COPPER 1 | 30 | PCBA COPPER 2 |
31 | PCBA COPPER 3 | 32 | BAT |
33 | SCREW L2.0 | 34 | FPCA SIDEKEY |
35 | SPK | 36 | COAXIAL CABLE |
37 | MOTOR LINEA | 38 | CAM AF 108M |
39 | CAM FF 2M | 40 | CAM FF 32M |
41 | PCBA SUB | 42 | CAM FF 8W |
43 | FLASH |
Know your phone
- Front camera
- Volume + key
- Volume – key
- Power key & side fingerprint sensor
- NFC
SIM/SD card installation
- Power off mobile.
- Refer to the following picture for SIM / SD card installation.
Charging the phone
You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone). Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty
FCC Statement
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: KJ6s (FCC ID: 2ADYY-KJ6S) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.745 W/kg and when properly worn on the body is 0.668 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or approved antenna
HiOS runs on AndroidTM OS. Android is a trademark of Google LLC
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>