RAINIER HYBRID Dual Fuel OPEN FRAME Generator User Manual
- June 7, 2024
- RAINIER
Table of Contents
HYBRID Dual Fuel OPEN FRAME Generator
R12000DF
Dual Fuel OPEN FRAME Generator
GASOLINE: 9500 Running Watts | 12000 Peak Watts PROPANE: 8550 Running Watts |
10800 Peak Watts
WARNING Operating, servicing and maintaining this equipment can expose you to
chemicals including engine exhaust, carbon monoxide, phthalates, and lead,
which are known to the State of California to cause cancer and birth defects
or other reproductive harm. To minimize exposure, avoid breathing exhaust, do
not idle the engine except as necessary, service your equipment in a well-
ventilated area and wear gloves or wash your hands frequently when servicing
your equipment. For more information go to www.P65Warnings.ca.gov.
DISCLAIMERS:
All information, illustrations and specifications in this manual are based on
the latest information available at the time of publishing. The illustrations
used in this manual are intended as representative reference views only.
Moreover, because of our continuous product improvement policy, we may modify
information, illustrations and/or specifications to explain and/or exemplify a
product, service or maintenance improvement. We reserve the right to make any
change at any time without notice. Some images may vary depending upon which
model is shown.
ALL RIGHTS RESERVED:
No part of this publication may be reproduced or used in any form by any means
graphic, electronic or mechanical, including photocopying, recording, taping
or information storage and retrieval systems without the written permission
of Rainier Outdoor Power Equipment, LLC.
DANGER
This manual contains important instructions for operating this generator. For
your safety and the safety of others, be sure to read this manual thoroughly
before operating the generator. Failure to properly follow all instructions
and precautions can cause you and others to be seriously hurt or killed.
TECHNICAL SPECIFICATIONS
Model Number
R12000DF
Running Watts
Gas: 9500 Propane: 8550
Peak Watts
Gasoline Tank Size (G)
Gas: 12000 Propane: 10800
6.6 Gallons
Rated
Engine
Oil
Speed Ignition Spark Disp Stroke X Capacity
(RPM) Type plug (cc)
Bore
(qt.)
Oil Type
3600 TCI
F7TC 457cc 68.8X92 1.1 qt. 10W30
Fuel Type
Gasoline, Propane
NOTICE
This generator is NOT equipped with altitude carburetor modification. Even
with a carburetor modification, engine horsepower will decrease about 3.5% for
each 300 meter (1,000 foot) increase in altitude. The effect of altitude on
horsepower will be greater if no carburetor modification is made. A decrease
in engine horsepower will decrease the power output of the generator.
HAVE QUESTIONS? Email us at service@rainierpower.com
2 |
FOR YOUR RECORDS:
Date of Purchase:
Generator Model Number:
Purchased from Store/Dealer:
Generator Serial Number:
IMPORTANT: KEEP YOUR PURCHASE RECEIPT TO ENSURE TROUBLE-FREE WARRANTY
COVERAGE. PRODUCT REGISTRATION
To ensure trouble-free warranty coverage, it is important you register your
Rainier generator. You can register your generator by either: 1. Filling in
the product registration form below and mailing to:
Product Registration Rainier Outdoor Power Equipment, LLC 777 Manor Park Drive
Columbus, Ohio 43228 2. Registering your product Online at
www.rainierpower.com/register To register your generator you will need to
locate the following information:
RAINIER PRODUCT REGISTRATION FORM
PERSONAL INFORMATION
GENERATOR INFORMATION
First Name: ___ Model Number:
Last Name: ___ Serial Number:__
Street Address: ___ Date Purchased:
Street Address: ___ Purchased From:____
City, State, ZIP:____
Country: __
Phone Number: ___
E-Mail: ___
| 3
TABLE OF CONTENTS
R12000DF TECHNICAL SPECIFICATIONS . . . . . . . . 2 PRODUCT REGISTRATION. . .
. . . . . . . . . . . . . . . . . . 3
For Your Records: . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Registration . . . . . . . . . . . . . . . . . . . . . . . 3 Product
Registration Form . . . . . . . . . . . . . . . . . . . 3
SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 5 Safety Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety Symbol Definitions . . . . . . . . . . . . . . . . . . . 5 General
Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . 6 Fuel Safety . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing Wheels and Feet. . . . . . . . . . . . . . . . . . . . 8 Installing
the Battery . . . . . . . . . . . . . . . . . . . . . . . . 9
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Generator Features . . . . . . . . . . . . . . . . . . . . . . . . . 10
Control Panel Features . . . . . . . . . . . . . . . . . . . . . 12
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Before Starting the Generator . . . . . . . . . . . . . . . . . 13 Location
Selection . . . . . . . . . . . . . . . . . . . . . . . 13 Grounding the
Generator . . . . . . . . . . . . . . . . . . 13 High Altitude
Operation/Conversion Kits . . . . . . 13 Power Cord . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 14 Engine Fluids and Fuel. . . . . . . . . .
. . . . . . . . . . . . . 15 Adding Gasoline to the Fuel Tank . . . . . . . .
. . . 15 Connecting LPG Tank . . . . . . . . . . . . . . . . . . . . . . . 16
Starting the Generator . . . . . . . . . . . . . . . . . . . . . . 17 Stopping
the Generator . . . . . . . . . . . . . . . . . . . . . . 18 Normal Operation
. . . . . . . . . . . . . . . . . . . . . . . 18 During an Emergency . . . . .
. . . . . . . . . . . . . . . 18
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . 19 Engine Oil
Maintenance . . . . . . . . . . . . . . . . . . . . . 20 Engine Oil
Specification . . . . . . . . . . . . . . . . . . . 20 Checking Engine Oil . .
. . . . . . . . . . . . . . . . . . . 20 Adding Engine Oil . . . . . . . . . .
. . . . . . . . . . . . . 20 Changing Engine Oil . . . . . . . . . . . . . . .
. . . . . . 21 Air Filter Maintenance . . . . . . . . . . . . . . . . . . . .
. . . 21 Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . 21
Spark Plug Maintenance . . . . . . . . . . . . . . . . . . . . . 22 Checking
and Adjusting Valve Lash . . . . . . . . . . . . . .23 Cleaning the Generator
. . . . . . . . . . . . . . . . . . . . . . 23 Storage . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 23
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . 24
4 |
SAFETY
SAFETY DEFINITIONS
The words DANGER, WARNING, CAUTION and NOTICE are used throughout this manual
to highlight important information. Be certain that the meanings of these
alerts are known to all who work on or near the equipment.
This safety alert symbol appears with most safety statements. It means
attention, become alert, your safety is involved! Please read and abide by the
message that follows the safety alerts symbol.
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor
or moderate injury.
NOTICE
Indicates a situation which can cause damage to the generator, personal
property and/or the environment, or cause the equipment to operate improperly.
NOTE: Indicates a procedure, practice or condition
that should be followed in order for the generator to function in the manner
intended.
SAFETY SYMBOL DEFINITIONS
| 5
SAFETY
GENERAL SAFETY RULES DANGER
Never use the generator in a location that is wet or damp. Never expose the
generator to rain, snow, water spray or standing water while in use. Protect
the generator from all hazardous weather conditions. Moisture or ice can cause
a short circuit or other malfunction in the electrical circuit.
Never operate the generator in an enclosed area. Engine exhaust contains carbon monoxide. Only operate the generator outside and away from windows, doors and vents.
WARNING
Voltage produced by the generator could result in death or serious injury. ·
Never operate the generator in rain or a flood plain unless proper precautions
are taken to avoid being subject
to rain or a flood. · Never use worn or damaged extension cords. · Always have
a licensed electrician connect the generator to the utility circuit. · Never
touch an operating generator if the generator is wet or if you have wet hands.
· Never operate the generator in highly conductive areas such as around metal
decking or steel works. · Always use grounded extension cords. Always use
three-wire or double-insulated power tools. · Never touch live terminals or
bare wires while the generator is operating. · Be sure the generator is
properly grounded before operating.
WARNING
Gasoline, gasoline vapors & are extremely flammable and explosive under
certain conditions. · Always refuel the generator outdoors, in a well-
ventilated area. · Never remove the fuel cap with the engine running. · Never
refuel the generator while the engine is running. Always turn engine off and
allow the generator to cool
before refueling. · Only fill fuel tank with gasoline. · Keep sparks, open
flames or other form of ignition (such as matches, cigarettes, static electric
sources) away
when refueling. · Never overfill the fuel tank. Leave room for fuel to expand.
Overfilling the fuel tank can result in a sudden
overflow of gasoline and result in spilled gasoline coming in contact with HOT
surfaces. Spilled fuel can ignite. If fuel is spilled on the generator, wipe
up any spills immediately. Dispose of rag properly. Allow area of spilled fuel
to dry before operating the generator. · Wear eye protection while refueling.
· Never use gasoline as a cleaning agent. · Store any containers containing
gasoline or propane in a well-ventilated area, away from any combustibles or
source of ignition. · Check for fuel leaks after refueling. Never operate the
engine if a fuel leak is discovered.
WARNING
Never operate the generator if powered items overheat, electrical output
drops, there is sparking, flames or smoke coming from the generator, or if the
receptacles are damaged.
Never use the generator to power medical support equipment.
NOTICE
Never modify the generator.
Never operate the generator if it vibrates at high levels, if engine speed
changes greatly or if the engine misfires often.
Always remove any tools or other service equipment used during maintenance from the generator before operating.
Always disconnect tools or appliances from the generator before starting.
6 |
SAFETY
FUEL SAFETY
DANGER
Gasoline and liquid petroleum gas (LPG) are highly explosive and flammable.
Explosions and fire can cause severe burns or death.
Gasoline and gasoline vapor (Gas) · Gasoline is highly flammable and
explosive. · Gas expands and contracts with different temperatures. · In case
of a gas fire, do not attempt to extinguish the flame
if the fuel shutoff valve is in the on position. Introducing an extinguisher
to a generator with an open fuel valve could create an explosion hazard. · Gas
has a distinctive odor, this will help detect potential leaks quickly. · Gas
vapors can cause a fire if ignited. · Gasoline is a skin irritant and needs to
be cleaned up immediately if it comes in contact with the skin. Liquid
Petroleum Gas (Propane/LPG) · LPG/Propane is highly flammable and explosive. ·
Flammable gas under pressure can cause a fire or explosion if ignited. ·
LPG/Propane can settle in low places because it is heavier than air. ·
LPG/Propane has a distinctive odor added to help detect potential leaks. ·
Always keep LPG/Propane tank in an upright position. · When exchanging
LPG/Propane tanks, be sure the tank value is the same type. · In case of a
LPG/Propane fire, do not attempt to extinguish unless the fuel supply can be
shut off. · LPG/Propane will burn the skin. Prevent skin contact at all times.
WARNING
Never use a gas container, LPG connector hose, LPG tank or any other fuel item
that appears to be damaged. When starting generator: · Make sure that the gas
cap, air filter, spark plug, fuel lines and exhaust system are properly in
place. · If you spill any gasoline on the tank, allow it to fully evaporate
before operating. · Make sure the generator and propane tank are on a flat
surface before operating. · If there is a propane odor do not start the unit
because there may be a potential leak. · Never place propane tank near engine
exhaust.
When transporting or servicing the generator: · Make certain the fuel shutoff
valve is off and the fuel
tank is empty. · Make sure the LPG tank and LPG hose is not attached
to the generator. · Disconnect the spark plug wire. When storing the
generator: · Store away from sparks, open flames, pilot lights, heat
and other sources of ignition. · Do not store gas or LPG tank near furnaces,
water
heaters or any other appliances that produce heat or have automatic ignitions.
CAUTION
Only use approved LPG tanks with OPD (overfilling prevention device) valve.
Always keep the tank in a vertical position with the valve on top and
installed at ground level on a flat surface. Do not allow tanks to be around
any heat source and make sure it is not exposed to the sun, rain and dust.
When transporting and storing, turn off the tank valve and fuel valve, and
disconnect the tank. Make sure to always cover the generator and tank outlet
with protective plastic caps.
CAUTION
Do not allow children to tamper or play with the propane tank or hose
connections.
WARNING
If there is a strong smell of propane while operating the generator close the
valve on the propane tank immediately. Once the propane is off, use soapy
water to check for leaks on the hose and connections on the tank valve and the
generator. Do not smoke or light a cigarette or check for leaks using any open
flame source such as a match or lighter. If a leak is found contact a
qualified technician to inspect and repair the LPG system before using the
generator.
| 7
ASSEMBLY
INSTALLING WHEELS AND FEET
BEFORE ASSEMBLING THE GENERATOR, REVIEW THE SAFETY SECTION STARTING ON PAGE 5.
CAUTION
Never lift the generator without assistance. The generator is heavy and
lifting without assistance could result in personal injury. Never use the
handles as a lifting point to support the entire weight of the generator. Only
use the handles to move the generator by lifting the handles and using the
wheels to move the generator. Use caution when collapsing the handles. Hands
and fingers could get caught and pinched.
NOTICE
Assembling the generator will require lifting the unit on one side. Make sure
all engine oil and fuel are drained from the unit prior to assembling. Once
assembled, the wheel kit is not intended for on-road use. The wheel kit is
designed for use on this generator only.
INSTALLING FEET TO FRAME
1. Place generator on a flat surface. 2. Place a piece of cardboard or other
soft material to
tip the generator onto, to protect the frame paint and prevent the generator
from sliding. Tip the generator onto the side. 3. Install the mounting foot to
the frame using M8 flange bolts. 1 – Mounting Feet 2 – Flange Bolts M8
INSTALLING WHEELS TO FRAME
1. Insert axle pin through washer and wheel.
Wheel Assembly
2. Install the wheel with axle pin through the axle bracket on the frame. The eye of the bolt should be facing toward the inside of the generator.
2
1
3
Assemble Wheel to Frame 3. Install the hairpin cotter through the axle pin to
lock
it in place. 1 – Axle Bracket 2 – Hairpin Clip 3 – Axle Pin 4. Repeat previous
steps on other wheel.
INSTALLING HANDLES TO FRAME
1. Line handle bolt holes with holes in frame and add bolts and nuts to
secure.
Assemble Mounting Feet to Frame 8 |
ASSEMBLY
INSTALLING THE BATTERY WARNING
To avoid electric shock: · ALWAYS connect the positive (+)
battery cable (red boot) first when connecting battery cables. · ALWAYS
disconnect the negative (-) battery cable (black boot) first when
disconnecting battery cables. · NEVER connect the negative (-) battery cable
(black boot) to the positive (+) post on the battery. · NEVER connect the
positive (+) battery cable (red boot) to the negative (-) post on the battery.
· NEVER touch both battery posts simultaneously. · NEVER place a metal tool
across both battery posts. · ALWAYS use insulated or nonconducting tools when
installing the battery. 1. Secure the positive (+) battery cable (red boot)
tightly to the positive (+) battery post. Make sure boot is over battery post.
2. Locate negative (-) cable attached to alternator cable, remove tie and
route to the negative (-) battery post.
1
4. Pull back the black boot and securely attach the negative (-) battery
cable (black boot) to the negative (-) battery post. Replace the black boot so
it protects the cable lug and battery post.
2 1
Attaching the Negative (-) Battery Wire (black) 1 – Positive (+) Battery Cable
(Red) 2- Negative (-) Battery Cable (Black)
NOTICE
The electric start generator is equipped with a battery charging feature. Once
the engine is running, a small charge is supplied to the battery via the
battery cables and will slowly recharge the battery.
(1) Negative Cable | 9
FEATURES
3
2 1 10
4
5
6
8
1 Fuel Selector Switch: Used to select and turn on gasoline or propane fuel
source.
2 Electric Start: Used to start the generator. 3 Fuel Cap: Close until
clicking sound is heard. 4 Control Panel: Contains the circuit breakers
and outlets. 5 Battery: Included for electric start models. 6 Oil Fill
Plug/Dipstick: Must be removed to add
and check oil.
9 7
7 Oil Drain Plug: Must be removed to drain engine oil. 8 Propane Hook Up: Hook
up your propane tank with
the LPG hose provided to this inlet. 9 Never Flat Wheels: For easy
portability. 10 Choke: Move to ON for cold start and OFF for warm
start.
10 |
FEATURES
12
13
14 15
12 Fuel Gauge: Indicates gas level. 13 Spark Plug Boot (Wire): Must be removed
when servicing the engine or the spark plug. 14 CARB Canister: Required for
models sold into
and used in California. 15 Muffler and Spark Arrester: Avoid contact
until engine is cooled down. Spark arrestor prevents sparks from exiting the
muffler. It must be removed for servicing.
| 11
FEATURES
CONTROL PANEL FEATURES
1
2
3
4 56
GASOLINE
ELECTRIC START
STAR T RU N STOP
VFT METE R
AC BREAKER
ON
20 A
OF F
120V AC 20 A 5-20R GFCI
AC BREAKER
ON
30 A
OF F
120V AC 30 A L5-30 R
120/240V AC 30 A
L14-30 R
120/240V AC 50 A
L14-50 R
MAIN BREAKE R
ON OF F
FUEL SELECTOR SWITCH
PROPANE
NEUTRAL BONDED TO FRAME
7
8
9 10 11
1 Fuel Selector Switch: Select and turn on gas or propane.
2 Electric Start Switch: Hold in Start position to start generator. Switch to
STOP to stop the engine.
3 Data Center: The VFT Meter is an LED display that will rotate through volts,
frequency, and lifetime run hours. You can press the MODE button to cycle
through the different displays. The frequency and voltage can vary +/- 5% and
still be within tolerance. Voltage Frequency in hertz Lifetime run hours
4 20-Amp Circuit Breaker: Circuit breaker limits the current that can be
delivered through the 120-volt outlet to 20amps.
12 |
5 120-Volt, 20-Amp Duplex Outlets (5-20R) GFCI: Each outlet is capable of
carrying a maximum of 20 amps on a single receptacle or a combination of both
receptacles.
6 30-Amp Circuit Breaker: Circuit breaker limits the current that can be
delivered through the 120volt outlet to 30amps.
7 120-Volt, 30 Amp Twistlock Outlet (L5-30R): Outlet can supply 120V output.
8 120/240-Volt, 30-Amp Twist Lock Outlet (NEMA L14-30R): Outlet can supply
either 120V or 240V up to 30 amps.
9 120/240-Volt, 50-Amp Outlet (NEMA 14-50R): Outlet can supply either 120V or
240V up to 50 amps.
10 Main Circuit Breaker: The main circuit breaker controls total output of all
outlets to protect the generator.
11 Ground Terminal: The ground terminal is used to ground the generator.
OPERATION
BEFORE STARTING THE GENERATOR
BEFORE STARTING THE GENERATOR, REVIEW SAFETY SECTION STARTING ON PAGE 5.
Location Selection Before starting the generator, avoid exhaust and location
hazards by verifying: · You have selected a location to operate the generator
that is outdoors and well ventilated. · You have selected a location with a
level and solid surface on which to place the generator. · You have selected a
location that is at least 15 feet (4.5 m) away from any building, other
equipment or combustible material. · If the generator is located close to a
building, make sure it is not located near any windows, doors and/or vents.
WARNING
Always operate the generator on a level surface. Placing the generator on non
level surfaces can cause the generator to tip over, causing fuel and oil to
spill. Spilled fuel can ignite if it comes in contact with an ignition source
such as a very hot surface. Prolonged exposure to engine exhaust can cause
serious injury or death. While charging a device do not place on the exhaust
side of the generator. Extreme heat caused by exhaust can damage the device,
and cause a potential fire hazard.
NOTICE
Only operate the generator on a solid, level surface. Operating the generator
on a surface with loose material such as sand or grass clippings can cause
debris to be ingested by the generator that could: · Block cooling vents ·
Block air intake system
Weather Never operate your generator outdoors during rain, snow or any
combination of weather conditions that could lead to moisture collecting on,
in or around the generator. Dry Surface Always operate the generator on a
dry surface free of any moisture. No Connected Loads Make sure the generator
has no connected loads before starting it. To ensure there are no connected
loads, unplug any electrical extension cords that are plugged into the control
panel receptacles.
NOTICE
Starting the generator with loads already applied to it could result in damage
to any appliance being powered off the generator during the brief start-up
period. Grounding the Generator The National Electric Code (NEC), as well as
many local electrical codes, may require the generator to be connected to
earth ground. The most common application that requires a ground rod is when
you are using the generator as a separately derived system to provide back up
power to your house. Typically this is when a transfer switch has a switched
neutral. As the generator application has many variables that cannot be
determined by the manufacturer of the generator, a licensed electrician will
need to determine if a grounding rod is needed. If a licensed electrician has
determined the application requires a ground rod, make sure it is connected to
earth ground by connecting the ground terminal on the control panel to earth
ground using copper wire (minimum 10 AWG). Consult a qualified electrician for
local grounding requirements.
WARNING
Be sure the generator is properly connected to earth ground before operating.
The generator must be grounded to prevent electrical shock due to faulty
appliances.
High Altitude Operation Engine power is reduced the higher you operate above
sea level. Output will be reduced approximately 3.5% for every 1000ft of
increased altitude from sea level. This is a natural occurrence and cannot be
adjusted by engine. Increased exhaust emissions can also result due to
increased fuel mixture. Other issues include hard starting, increased fuel
consumption and spark plug fouling.
| 13
OPERATION
POWERCORD
Using Extension Cords Rainier Outdoor Power Equipment assumes no
responsibility for the content within this table. The use of this table is the
responsibility of the user only. This table is intended for reference only.
The results produced by using this table are not guaranteed to be correct or
applicable in all situations as the type and construction of cords are highly
variable. Always check with local regulations and a licensed electrician prior
to installing or connecting an electrical appliance.
14 |
OPERATION
ADDING / CHECKING ENGINE FLUIDS AND FUEL
BEFORE ADDING/CHECKING ENGINE FLUIDS AND FUEL, REVIEW SAFETY SECTION STARTING
ON PAGE 5.
DANGER
Filling the fuel tank with gasoline while the generator is running can cause
gasoline to leak and come in contact with hot surfaces that can ignite the
gasoline.
Before starting the generator, always check: · Level of Engine oil · Level of
gasoline in the fuel tank · Secured connection to an undamaged LPG tank It is
not safe to add gasoline to the fuel tank or engine oil to the engine while
the engine is running or the engine and muffler are hot.
CHECKING AND / OR ADDING ENGINE OIL WARNING
Internal pressure can build in the engine crankcase while the engine is
running. Removing the oil fill plug/ dipstick while the engine is hot can
cause extremely hot oil to spray out of the crankcase and can severely burn
skin. Allow engine oil to cool for several minutes before removing the oil
fill plug/ dipstick.
The unit as shipped does not contain oil in the engine. You must add engine
oil before starting the generator for the first time.
NOTICE
The engine does not contain engine oil as shipped. Attempting to start the
engine can damage engine components. The owner of the generator is responsible
to ensure the proper oil level is maintained during the operation of the
generator. Failure to maintain the proper oil level can result in engine
damage.
NOTICE
During the first five hours of operating the generator make sure to not exceed
50% of the rated running watts until the unit is broken in properly. Make sure
to vary to load occasionally to allow stator windings to heat and cool.
Adjusting the load will also help seat piston rings. Check oil more often
during the first couple times of operating the generator.
NOTICE
Weather will affect engine oil performance. Change the type of engine oil used
based on weather conditions to suit the engine needs.
ADDING GASOLINE TO THE FUEL TANK
BEFORE ADDING GAS TO THE TANK PLEASE REVIEW FUEL SAFETY SECTION ON PAGE 7
WARNING
Never refuel the generator while the engine is running.
Always turn the engine off and allow the generator to cool before refueling.
Required Gasoline Only use gasoline that meets the following requirements: ·
Unleaded gasoline only · Gasoline with maximum 10% ethanol added · Gasoline
with an 87 octane rating or higher Filling the Fuel Tank Follow the steps
below to fill the fuel tank: 1. Shut off the generator. 2. Allow the generator
to cool down so all surface areas of
the muffler and engine are cool to the touch. 3. Move the generator to a flat
surface. 4. Clean area around the fuel cap. 5. Remove the fuel cap by rotating
counterclockwise. 6. Slowly add gasoline into the fuel tank. Be very careful
not to overfill the tank. The gasoline level should NOT be higher than the
filler neck. 7. Install the fuel cap by rotating clockwise until you hear a
click, indicating the cap is completely installed.
Maximum Gasoline Fill Level
CAUTION
Avoid prolonged breathing of gasoline vapors.
| 15
OPERATION
CONNECTING THE LPG/PROPANE TANK
BEFORE CONNECTING PROPANE TANK TO THE GENERATOR PLEASE REVIEW FUEL SAFETY
SECTION ON PAGE 7
Connecting LPG Tank 1. Make sure the generator is off, on a flat surface in
well
ventilated area. 2. Make sure propane tank valve is in the off position. 3.
Make sure the fuel selector switch on the generator
control panel is pointing downward to “Propane”. 4. Remove the plastic cover
on the generator propane
inlet valve. 5. Using your fingers tighten the LPG hose (included)
end below to the generator propane inlet. DO NOT OVER-TIGHTEN 35-88 Ib-in
maximum. 6. Attach the other end of the hose to a tank of LPG/ Propane and
hand tighten. 7. Check all connections for leaks by wetting the fittings with
soapy water. Anywhere that bubbles appear or grow indicates a leak in the
connection. If a leak exists at a fitting then turn off the tank valve and
tighten the fitting. Turn the gas back on and recheck with soapy water again.
If the leak continues or if the leak is not at a fitting then do not use the
generator and contact customer service.
NOTICE
· Use only standard LPG tanks with Type 1, right hand Acme threads.
· Verify the requalification date on the tank has not expired. · All new tanks
must be purged of air and moisture prior to filling.
Used tanks that have not been plugged or kept closed must also be purged · The
purging process should be done by a LPG supplier. (Tanks from an exchange
supplier should have been purged and filled properly already) · Always
position the tank so the connection between the valve and the gas inlet won’t
cause sharp bends or kinks in the hose.
WARNING
Do not start generator if you smell propane. This may result in explosion
hazard. Do not use provided LPG hose for any other appliances. Always turn off
the propane tank and disconnect LPG hose when not in use.
BEFORE STARTING THE GENERATOR
BEFORE STARTING THE GENERATOR, REVIEW SAFETY SECTION STARTING ON PAGE 5.
Before attempting to start the generator, verify the following: · The engine
is filled with engine oil. · The generator is situated in a proper location. ·
The generator is on a dry surface. · All loads are disconnected from the
generator. · The generator is properly grounded the Generator. · Propane
connection is secure with no leaks or
damage.
DANGER
Never use the generator in a location that is wet or damp. Never expose the
generator to rain, snow, water spray or standing water while in use. Protect
the generator from all hazardous weather conditions. Moisture or ice can cause
a short circuit or other malfunction in the electrical circuit. Never operate
the generator in an enclosed area. Engine exhaust contains carbon monoxide.
Only operate the generator outside and away from windows, doors and vents.
NOTICE
The engine is equipped with a low oil shutdown switch. If the oil level
becomes low, the engine may shut down and not start until the oil is filled to
the proper level. Poor oil quality may interfere with the operation of the low
oil shutdown switch. The owner of the generator is responsible to ensure the
proper oil level is maintained during the operation of the generator. Failure
to maintain the proper oil level can result in engine damage.
NOTICE
When operating on LPG it is common for frost to form on the tank and
regulators. This is not an indication of a problem. The amount of frost that
forms can be affected by the size of the container, the amount of fuel being
used, the humidity of the air and other operating conditions. In standard use
this frost may reduce flow of gas and lower performance. If frost becomes an
issue try exchanging fuel tanks to allow the first tank to warm up. You can
also temporarily warm the tank up by pouring warm water over the top of the
propane tank.
16 |
OPERATION
SWITCHING FUEL SOURCES
BEFORE ADDING GAS TO THE TANK PLEASE REVIEW FUEL SAFETY SECTION ON PAGE 7
The below assumes that the propane fuel line is already attached to the
generator securely and safely.
While the unit is running simply turn the FUEL SELECTOR knob to the desired
fuel source. If you want to switch from gasoline to propane make sure the
propane tank valve is open before you switch. When you move from propane to
gasoline shut the propane valve after you have switched to gas.
NOTICE
If you do not plan on operating the unit on propane do not leave the propane
tank valve open. When starting on propane the engine may run rough for a few
seconds while it purges gasoline in the carburetor. If the engine fails when
switching fuel sources simply restart the unit on the fuel source that you
switched to.
STARTING THE GENERATOR
Be sure to check oil and gas levels before starting. If it is the first time
starting make sure to add oil. 1. Make sure nothing is plugged into power
outlets. 2. Verify the battery is properly installed and both battery
cables are attached. 3. Make sure the circuit breakers are properly set. 4.
Select fuel source for start up:
FOR GASOLINE: a. Move the fuel shut off valve to the ON position.
ON OFF
FOR LPG/PROPANE: a. Make sure the LPG hose is safely secured from
the generator to the tank. b. Turn the fuel selector knob to PROPANE. c. Fully
open the valve on the propane tank.
5. If engine is cold, move the choke lever to the ON position. If engine is
warm move the choke to the OFF position.
6. Electric Start: Push and hold the engine control switch in the START
position until the engine starts. Once the engine starts, release the engine
control switch; the switch will automatically move into the RUN position.
START RUN STOP
Note: If the engine fails to start after 5 seconds, release the engine control
switch. Let the generator sit idle for 15 seconds and then repeat step 6a. If
the cranking speed drops after each unsuccessful attempt, then the battery may
not be adequately charged. Manually start the generator by following steps
below:
Manual Start: Firmly grasp and pull the recoil handle slowly until you feel
increased resistance. At this point, apply a rapid pull while pulling up and
slightly away from the generator.
b. Turn fuel selector knob to GASOLINE.
7. As the engine starts and stabilizes, gradually move the choke lever back to the OFF position.
Fuel Shut Off – ON Fuel Selector – GASOLINE
8. Wait 15 seconds for engine to stabilize before plugging in electronic devices. | 17
OPERATION
STOPPING THE GENERATOR
Normal Operation During normal operation, use the following steps to stop your
generator: 1. Remove any connected loads from the control
panel receptacles. 2. Allow the generator to run at “no load” to reduce
and stabilize engine and alternator temperatures. 3. If you are operating on
gas move the fuel shut off
valve to OFF. If you are operating on propane shut off the tank valve. Wait
for engine to shut off due to lack of fuel. 4. Position the engine control
switch to STOP. During an Emergency If there is an emergency and the generator
must be stopped quickly, position the electric start switch to the STOP
position immediately.
MAINTENANCE
ON OFF
Fuel Shut Off – OFF
Propane Tank Valve – CLOSED
START RUN STOP
Engine Switch – STOP
BEFORE PERFORMING MAINTENANCE ON THE GENERATOR, REVIEW THE SAFETY SECTION STARTING ON PAGE 5, AS WELL AS THE FOLLOWING SAFETY MESSAGES.
WARNING
Avoid accidentally starting the generator during maintenance by removing the
spark plug boot from the spark plug. For electric start generators, also
disconnect the battery cables from the battery (disconnect the black negative
(-) cable first) and place the cables away from the battery posts to avoid
arcing. Allow hot components to cool to the touch prior to performing any
maintenance procedure. 18 |
WARNING
Internal pressure can build in the engine crankcase while the engine is
running. Removing the oil fill plug/ dipstick while the engine is hot can
cause extremely hot oil to spray out of the crankcase and can severely burn
skin. Allow engine oil to cool for several minutes before removing the oil
fill plug/dipstick. Always perform maintenance in a wellventilated area.
Gasoline fuel and fuel vapors are extremely flammable and can ignite under
certain conditions.
MAINTENANCE
MAINTENANCE SCHEDULE WARNING
Failure to perform periodic maintenance or not following maintenance
procedures can cause the generator to malfunction and could result in death or
serious injury.
NOTICE
Periodic maintenance intervals vary depending on generator operating
conditions. Operating the generator under severe conditions, such as sustained
high-load, high-temperature, or unusually wet or dusty environments, will
require more frequent periodic maintenance. The intervals listed in the
maintenance schedule should be treated only as a general guideline.
CAUTION
Avoid skin contact with engine oil or gasoline. Prolonged skin contact with
engine oil or gasoline can be harmful. Frequent and prolonged contact with
engine oil may cause skin cancer. Take protective measures and wear protective
clothing and equipment. Wash all exposed skin with soap and water. Following
the maintenance schedule is important to keep the generator in good operating
condition. The following is a summary of maintenance items by periodic
maintenance intervals.
TABLE 1: MAINTENANCE SCHEDULE – OWNER PERFORMED
Maintenance Item Engine Oil Cooling Features Air Filter Spark Plug Spark Arrestor
Before Every Use
Check Level Check/Clean
Check –
After First 20 Hours or First Month of Use
Change –
After 50 Hours After 100 Hour
of Use or Every of Use or Every
6 Months
6 Months
Change
–
–
–
Clean* –
Check/Clean
–
Check/Clean
After 300 Hours of Use or Every Year
Replace Replace –
*Service more frequently if operating in dry and dusty conditions
TABLE 2: MAINTENANCE SCHEDULE – AUTHORIZED RAINIER SERVICE DEALER PERFORMED
Maintenance Item Valve Clearance Fuel Filter
Before Every Use –
After First 20 Hours or First Month of Use
–
After 50 Hours After 100 Hour
of Use or Every of Use or Every
6 Months
6 Months
–
–
–
Check/Clean
After 300 Hours of Use or Every Year
Check/Adjust –
Idle Speed
–
–
–
–
Check/Adjust
| 19
MAINTENANCE
ENGINE OIL MAINTENANCE
Engine Oil Specification 1. Only use the engine oil specified in graphic
below. 2. Only use 4-stroke/cycle engine oil. NEVER USE
2-STROKE/CYCLE OIL. Synthetic oil is an acceptable substitute for conventional
oil.
6. Check oil level: When checking the engine oil, remove the oil fill plug/dipstick and wipe it clean. Thread the oil fill plug/dipstick all the way back in and then remove and check the oil level on the oil fill plug/ dipstick. · Acceptable Oil Level Oil is visible on the crosshatches between the H and L lines on the oil fill plug/dipstick. · Low Oil Oil is below the L line on the oil fill plug/ dipstick.
Recommended Oil
CHECKING ENGINE OIL NOTICE
Always maintain proper engine oil level. Failure to maintain proper engine oil
level could result in severe damage to the engine and/or shorten the life of
the engine. Always use the specified engine oil. Failure to use the specified
engine oil can cause accelerated wear and/or shorten the life of the engine.
Engine oil level should be checked before every use. 1. Always operate or
maintain the generator
on a flat surface. 2. Stop engine if running. 3. Let engine sit and cool for
several minutes (allow
crankcase pressure to equalize). 4. With a damp rag, clean around the
oil fill plug/dipstick. 5. Remove oil fill plug/dipstick.
ADDING ENGINE OIL
1. Always operate or maintain the generator on a flat surface.
2. Stop engine if running. 3. Let engine sit and cool for several minutes
(allow
crankcase pressure to equalize). 4. Thoroughly clean around the oil fill
plug/dipstick. 5. Remove oil fill plug/dipstick and wipe clean. 6. Select the
proper engine oil. 7. Using a funnel, slowly add engine oil to the engine.
Stop frequently to check the level to avoid overfilling. 8. Continue to add
oil until the oil is at the correct level.
Oil Fill Plug/Dipstick 20 |
MAINTENANCE
CHANGING ENGINE OIL
1. Stop the engine. 2. Let engine sit and cool for several minutes (allow
crankcase pressure to equalize). 3. Place oil pan (or suitable container)
under the oil
drain plug. 4. With a damp rag, thoroughly clean around the oil
drain plug. 5. Remove the oil drain plug. Once removed, place the
oil drain plug on a clean surface.
AIR FILTER MAINTENANCE WARNING
Never use gasoline or other flammable solvents to clean the air filter. Use
only household detergent soap to clean the air filter.
Cleaning the Air Filter The air filter must be cleaned after every 50 hours of
use or 3 months (frequency should be increased if generator is operated in a
dusty environment). 1. Turn off the generator and let it cool for several
minutes if running. 2. Move the generator to a flat, level surface. 3. Unclip
the clips on the top and bottom of the air
filter cover.
oil pan
Oil Drain Plug 6. Allow oil to completely drain. 7. Replace oil drain plug. 8.
Fill crankcase with oil following the steps outlined in
Adding Engine Oi.
NOTICE
Never dispose of used engine oil by dumping the oil into a sewer, on the
ground, or into ground water or waterways. Always be environmentally
responsible. Follow the guidelines of the EPA or other governmental agencies
for proper disposal of hazardous materials. Consult local authorities or
reclamation facility.
4. Remove the black coarse air filters. 5. Wash the foam air filter elements
by submerging
the elements in a solution of household detergent soap and warm water. Slowly
squeeze the foam to thoroughly clean.
NOTICE
NEVER twist or tear the foam air filter element during cleaning or drying.
Only apply slow but firm squeezing action.
6. Rinse in clean water by submerging the air filter elements in fresh water
and applying a slow squeezing action
| 21
MAINTENANCE
Cleaning the Air Filter – Continued
NOTICE
Never dispose of soap cleaning solution used to clean the air filter by
dumping the solution into a sewer, on the ground, or into ground water or
waterways. Always be environmentally responsible. Follow the guidelines of the
EPA or other governmental agencies for proper disposal of hazardous materials.
Consult local authorities or reclamation facility. 7. Dispose of used soap
cleaning solution properly. 8. Dry the air filter elements by again applying a
slow
firm squeezing action. 9. Once the air filters are dry, coat the air filters
with
clean engine oil.
10. Squeeze the filters to remove any excess oil. 11. Install the filters
back into the unit. If there are two
filters make sure the gray (fine) air filter goes in first followed by the
black (coarse) air filter on the outside. 12. Install the air filter cover and
secure the air filter assembly.
SPARK PLUG MAINTENANCE
The spark plug must be checked and cleaned after every 100 hours of use or 6
months and must be replaced after 300 hours of use or every year. 1. Stop the
generator and let it cool for several
minutes if running. 2. Move the generator to a flat, level surface. 3. Remove
the spark plug boot by firmly pulling the
plastic spark plug boot handle directly away from the engine.
NOTICE
Never apply any side load or move the spark plug laterally when removing the
spark plug. Applying a side load or moving the spark plug laterally may crack
and damage the spark plug boot. 22 |
Remove Spark Plug Boot
4. Clean area around the spark plug.
5. Using the 13/16″ spark plug socket wrench provided, remove the spark plug from the cylinder head.
6. Place a clean rag over the opening created by the removal of the spark plug to make sure no dirt can get into the combustion chamber.
Inspect the spark plug for: · Cracked or chipped insulator
SPARK PLUG GAP
· Excessive wear
· Spark plug gap (the acceptable limit of 0.0270.032 in. [0.70 0.80 mm]).
NOTICE
Use only recommended spark plugs when servicing. The manufacturer is not
responsible for engine damage when using spark plugs not recommended by the
manufacturer.
7. Install the spark plug by carefully following the steps outlined below: a.
Carefully insert the spark plug back into the cylinder head. Hand-thread the
spark plug until it bottoms out. b. Using the 13/16″ spark plug socket wrench
provided, turn the spark plug to ensure it is fully seated. c. Replace the
spark plug boot, making sure the boot fully engages the spark plug’s tip.
Recommended Spark Plug Replacement: AC Delco: 4EXLS Autolite: 52 Champion:
N9YC Bosch: W7DC Torch: F7TC
MAINTENANCE
CHECKING AND ADJUSTING VALVE LASH CAUTION
Checking and adjusting valve lash must be done when the engine is cold.
1. Remove the rocker arm cover and carefully remove the gasket. If the gasket
is torn or damaged, it must be replaced.
2. Remove the spark plug so the engine can be rotated more easily.
3. Rotate the engine to top dead center (TDC) of the compression stroke.
Looking through the spark plug hole, the piston should be at the top.
4. Both the rocker arms should be loose at TDC on the compression stroke. If
they are not, rotate the engine 360°.
5. Insert a feeler gauge between the rocker arm and the push rod and check
for clearance. See Table below for valve lash specifications
2 1
3
4
5
(1) Push Rod, (2) Feeler Gauge Area (3) Rocker Arm, (4) Jam Nut, (5) Adjusting Nut
Standard Valve Lash
Intake Valve
Exhaust Valve
Valve Lash
0.0031 ± 0.0047 in (0.08 ± 0.12 mm)
0.0051 ± 0.0066 in (0.13 ± 0.17 mm)
Bolt Torque
8-12N.m
8-12N.m
6. If an adjustment is required, hold the adjusting nut and loosen the jam nut.
7. Turn the adjusting nut to obtain the correct valve lash. When the valve lash is correct, hold the adjusting nut and tighten the jam nut to 106 in-lb (12 N·m).
8. Recheck the valve lash after tightening the jam nut.
9. Perform this procedure for both the intake and exhaust valves.
10. Install the rocker arm cover, gasket and spark plug.
CLEANING THE GENERATOR
It is important to inspect and clean the generator before every use. Clean All
Engine Air Inlet and Outlet Ports Make sure all engine air inlet and outlet
ports are clean of any dirt and debris to ensure the engine does not run hot.
Clean All Engine Cooling Fins Use a damp rag and a brush to loosen and
remove all dirt on or around the engine’s cooling fins. Clean All Alternator
Cooling Air Inlets and Exhaust Ports Make sure the cooling air inlets and
exhaust ports of the alternator are free of any debris and obstructions. Use a
vacuum cleaner to remove dirt and debris stuck in the cooling air inlets and
exhaust ports. General Cleaning of the Generator Use a damp rag to clean all
remaining surfaces.
STORING GENERATOR WARNING
Never store a generator with fuel in the tank indoors or in a poorly
ventilated area where the fumes can come in contact with an ignition source
such as a: 1) pilot light of a stove, water heater, clothes dryer or any other
gas appliance; or 2) spark from an electric appliance.
NOTICE
Gasoline stored for as little as 60 days can go bad, causing gum, varnish and
corrosive buildup in fuel lines, fuel passages and the engine. This corrosive
buildup restricts the flow of fuel, preventing an engine from starting after a
prolonged storage period.
Proper care should be taken to prepare the generator for any storage. 1. Make
sure the Engine Switch is switched to STOP
so the generator does not draw power from battery. 2. Clean the generator as
outlined in Cleaning the
Generator. 3. Drain all gasoline from the fuel tank as best as
possible. 4. Drain fuel out of carburetor bowl by loosening screw.
| 23
fuel pan
MAINTENANCE
5. With the fuel shut off valve open, start the engine and allow the
generator to run until all the remaining gasoline in the fuel lines and
carburetor is consumed and the engine shuts off.
6. Close the fuel shut off valve. 7. Change the oil. 8. Remove the spark plug
and place about 1
tablespoon of oil in the spark plug opening. While placing a clean rag over
the spark plug opening, slowly pull there coil handle to allow the engine to
turn over several times. This will distribute the oil and protect the cylinder
wall from corroding during storage.
TROUBLESHOOTING
9. Replace the spark plug. 10. Move the generator to a clean, dry place for storage.
WARNING
Before attempting to service or troubleshoot the generator, the owner or
service technician must first read the owner’s manual and understand and
follow all safety instructions. Failure to follow all instructions may result
in conditions that can lead to voiding of the EPA certification or product
warranty, serious personal injury, property damage or even death.
PROBLEM
Engine is running, but no electrical output
POTENTIAL CAUSE
SOLUTION
1. Circuit breakers are tripped.
1. Reset the circuit breakers and check for overload condition.
2. The power cord’s plug connector is not fully 2. Verify plug connector is firmly engaged in the
engaged in the generator’s outlet.
generator’s outlet.
3. Faulty or defective power cord
3. Replace power cord.
4. Faulty or defective electrical appliance
4. Try connecting a known good appliance to verify the generator is producing electrical power.
5. If trying 1-4 above does not solve the
6. Take the generator to your nearest authorized
problem, the cause might be the generator has service dealer.
a fault.
Engine runs erratic; does not hold a steady RPM.
Generator suddenly stops running.
24 |
1. Dirty air filter 2. Applied loads maybe cycling on and off
3. If trying 1-2 above does not solve the problem, the cause might be a fault
in the generator
1. Clean the air filter. 2. As applied loads cycle, changes in engine speed may occur; this is a normal condition. 3. Take the generator to your nearest authorized service dealer.
1. Generator is out of fuel. 2. The low oil shut down switch has stopped the engine. 3. Too much load 4. If trying 1-3 above does not solve the problem,the cause might be a fault in the generator.
1. Check fuel level. Add fuel if necessary. 2. Check oil level and add oil if
necessary.
3. Restart the generator and reduce the load. 4. Take the generator to your
nearest authorized service dealer.
TROUBLESHOOTING
Engine will not start or remain running while trying to start.
1. Fuel shutoff valve is in the OFF position.
1. Move the fuel shut off valve to the ON position.
2. Generator is out of gasoline.
2. Add gasoline to the generator.
3. Fuel flow is obstructed.
3. Inspect and clean fuel delivery passages.
4. Starting battery may have insufficient charge 4. On electric start models only. Check battery output and charge battery as necessary.
5. Dirty air filter
5. Check and clean the air filter.
6. Low oil level shut down switch is preventing 6. Check oil level and add oil if necessary. the unit from starting.
7. Spark plug boot is not fully engaged with the spark plug tip.
7. Firmly push down on the spark plug boot to ensure the boot is fully engaged
8. Spark plug is faulty.
8. Remove and check the spark plug. Replace if faulty.
9. Dirty/plugged spark arrestor
9. Check and clean the spark arrestor.
10. Stale fuel
10. Drain fuel and replace with fresh fuel.
11. If trying 1-10 above does not solve the
11. Take the generator to your nearest authorized
problem, the cause might be the generator has service dealer.
a fault.
Frost on the propane tank or regulator
1. This can be a normal occurrence caused when liquid propane changes phase to a gas. As this process occurs the fuel tank or regulator will cool and allow humid air surrounding the propane tank or regulator to condense into frost.
1. As this can be normal, providing all the propane fuel handling equipment is functioning normally, no remedy is needed.
2. The propane tank is not equipped with a OPD (rollover protection device) and has been stored in a horizontal position allowing liquid propane to enter the downstream fuel handling equipment.
2. If you suspect your propane fuel tank is not equipped with a OPD device, discontinue operation immediately and replace the propane fuel tank with a propane tank equipped with a roll over protection device.
3. Propane fuel tank over filled.
3. If you suspect your propane fuel tank has been overfilled, discontinue operation immediately and return the propane fuel tank to the place of purchase or refilling.
Propane fuel smell
1. Fuel regulator or fuel hose and fittings not securely sealed. 2. Propane
fuel regulator vent active.
3. Residual fuel from the carburetor dispersing after operation.
1. Using a soap solution check each connection and tighten as needed. 2. The propane fuel regulator is equipped with a small vent that will allow a small amount of propane fuel vapor to escape from the regulator when the propane tank valve is opened. This can be normal providing the venting of the propane is brief. If you suspect that this is abnormal, immediately discontinue use and have the propane regulator inspected by a qualified technician. 3. Normal, no remedy is needed.
Poor performance or engine stalling on propane
1. Propane fuel line kinked or crushed.
1. Inspect propane fuel line and remove kinks or other obstructions.
2. Fuel selector valve not properly positioned.
2. Rotate the fuel valve fully until the pointer is directly in line with the desired fuel.
3. Gasoline not purged from the carburetor before switching to propane.
3. Turn the propane fuel tank valve to closed. Move the fuel selector valve to propane. Turn the gasoline fuel valve to off. Start the engine and allow the engine to run until the fuel has been consumed in the carburetor. Begin propane start up procedure.
| 25
WARRANTY
RAINIER OUTDOOR POWER EQUIPMENT’S RESPONSIBILITY Rainier Outdoor Power
Equipment warrants to the original purchaser that its Rainier line of
generators will be free from defects in material and workmanship. Under normal
use and maintenance from the date of purchase, Rainier Outdoor Power Equipment
agrees to repair or replace at Rainier Outdoor Power Equipment’s discretion,
any defective product free of charge at any authorized Rainier Outdoor Power
Equipment Authorized Service Dealer within the below listed applications, time
periods, limitations, and exclusions. THIS LIMITED WARRANTY IS EXTENDED TO THE
ORIGINAL PURCHASER ONLY AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT
FOR EMISSION RELATED PARTS. This warranty is separate from the Emission
Control Warranty Statement supplied with your new product. Please consult the
Emission Control Warranty Statement for details regarding emission related
parts. OWNER’S RESPONSIBILITY To ensure trouble free warranty coverage it is
important that you register your Rainier generator. You may register on-line
at www.rainierpower.com/register, or by filling out and returning to Rainier
Outdoor Power Equipment the warranty registration card supplied with your
generator. Registering your product confirms your warranty coverage and
provides a direct link between you and Rainier Outdoor Power Equipment if we
find it necessary to contact you. Transportation charges on product submitted
for repair or replacement under this warranty are the sole responsibility of
the purchaser. Your receipt for purchase including date, model and serial
number must be maintained and presented to an Rainier Outdoor Power Equipment
Authorized Service Dealer for warranty service. Proof of purchase rests solely
with you, the original purchaser. You must demonstrate reasonable care and
use, and follow preventive maintenance, storage, fuel and oil usage as
prescribed in the operator’s manual for your Rainier generator. Should a
product difficulty occur, you must, at your expense, deliver or ship your
Rainier generator to an Rainier Outdoor Power Equipment Authorized Service
Dealer for warranty repairs (which must occur within the applicable warranty
period), and arrange for pick-up or return of your generator after the repairs
have been made. PRODUCT WARRANTY APPLICATIONS AND PRODUCT WARRANTY PERIODS
Consumer Application For the purpose of this limited warranty “Consumer
Application” means usage by the original purchaser for the purpose of personal
residential household or recreational use. · Replacement parts will be covered
for a period of three years from the date of purchase. · If proof of purchase
is not available to establish the purchase date nor is the equipment
registered as suggested herein, the date of
manufacturing as recorded by Rainier Outdoor Power Equipment will start the
product warranty period. Commercial or Rental Applications For the purpose of
this limited warranty “Commercial Application” means usage by the original
purchaser for the purpose of income producing, business related use. Once a
generator has been used for income producing and business related purposes, it
shall thereafter be considered a “Commercial Application” and the following
warranty will apply. · Replacement parts will be covered for a period of six
months from the date of purchase. · If proof of purchase is not available to
establish the purchase date nor is the equipment registered as suggested
herein, the date of
manufacturing as recorded by Rainier Outdoor Power Equipment will start the
product warranty period. NON-WARRANTABLE APPLICATIONS THE RAINIER OUTDOOR
POWER EQUIPMENT LINE OF GENERATORS IS EXPRESSLY NOT RECOMMENDED FOR NOR
WARRANTED FOR THE FOLLOWING APPLICATIONS: Medical and Life Support Uses This
product is not recommended for and is NOT warranted for the use to power
Medical and Life Support equipment or devices. Prime Power This warranty
does not apply to generators used for Prime Power (primary source of power) in
place of utility power where utility power service is present or where utility
power service does not normally exist, regardless of whether a Consumer
Application or Commercial Application is involved.
20190801KD – Rev 2 26 |
WARRANTY
Exclusions: · Cosmetic defects such as paint, decals, etc. · Rainier Outdoor
Power Equipment portable generators that utilize non-Rainier Outdoor Power
Equipment replacement parts. · Costs of normal maintenance and adjustments. ·
Failures caused by any contaminated fuels, oils, or lack of proper oil levels.
· Repairs or diagnostics performed by individuals other than Rainier Outdoor
Power Equipment authorized dealers not authorized in
writing by Rainier Outdoor Power Equipment. · Failures due to normal wear and
tear, accident, misuse, abuse, negligence or improper use. As with all
mechanical devices, the Rainier
Outdoor Power Equipment engines need periodic part(s) service and replacement
to perform as designed. This warranty will not cover repair when normal use
has exhausted the life of a part(s) or engine. · Failures caused by any
external cause or act of God, including but not limited to, collision, theft,
vandalism, riot, war, fire, freezing, lightning, earth-quake, windstorm, hail,
water, flood, tornado, or hurricane. · Damage related to rodent and/or insect
infestation. · Products that are modified or altered in a manner not
authorized in writing by Rainier Outdoor Power Equipment. · Any incidental,
consequential or indirect damages caused by defects in materials or
workmanship, or any delay in repair or replacement of the defective part(s). ·
Failure due to misapplication. · Telephone, cellular phone, facsimile,
Internet access, or other communication expenses. · Expenses related to
“customer instruction” or troubleshooting where no manufacturing defect is
found. · Overnight freight or special shipping costs for replacement part(s).
· Overtime, holiday or emergency labor. · Starting battery, fuses, light bulbs
and engine fluids. DISCLAIMER OF IMPLIED WARRANTIES This limited warranty is
in lieu of all other expressed or implied warranties, including any warranty
of FITNESS FOR A PARTICULAR PURPOSE OR USE and any implied warranty of
MERCHANTABILITY otherwise applicable to Rainier Outdoor Power Equipment’s line
of generators. Rainier Outdoor Power Equipment and its affiliated companies
shall not be liable for any special, incidental or consequential damage,
including lost profits. There are no warranties extended other than as
provided herein. This limited warranty may be modified only by Rainier Outdoor
Power Equipment. Any implied warranties allowed by law shall be limited in
duration to the terms of the express warranty provided herein. Some states do
not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation may
not apply to you. This warranty gives you specific legal rights. You also have
other rights from state to state. Rainier Outdoor Power Equipment’s ONLY
LIABILITY SHALL BE THE REPAIR OR REPLACEMENT AS STATED ABOVE. IN NO EVENT
SHALL Rainier Outdoor Power Equipment BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES, EVEN IF SUCH DAMAGES ARE A DIRECT RESULT OF Rainier
Outdoor Power Equipment’s NEGLIGENCE. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation
may not apply to you. This warranty gives you specific legal rights and you
may also have other rights from state to state. This limited warranty is given
by Rainier Outdoor Power Equipment, 777 Manor Park Drive, Columbus, OH 43228
20190801KD – Rev 2 | 27
RainierPower.com
28 |
Version 07.06.18KD Rev2
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>