TECNO BG6S SPARK Go 2024 Smartphone User Manual
- June 1, 2024
- TECNO
Table of Contents
TECNO BG6S SPARK Go 2024 Smartphone
Specifications
- Model : SPARK Go 2024
- Operating System: HiOS on Android™ OS
- Front Camera
- Volume + Key and Volume – Key
- Power Key & Side Fingerprint Sensor
Explosion diagram specification
| 1 | FL(CTP+LCM) | 2 | REC DECO |
|---|---|---|---|
| 3 | F HSG ASM | 4 | F FLASH HOOD |
| 5 | PS LENS | 6 | R CAM 8W AD |
| 7 | F CAM | 8 | R CAM 13M |
| 9 | R CAM 8W | 10 | PCBA MB |
| 11 | PS RUBBER | 12 | SIM CARD HOLDER |
| 13 | PCBA COPPER D | 14 | MI HOUSING |
| 15 | SCREW L3.5 | 16 | BAT COVER ASM |
| 17 | R FLASHHOOD | 18 | R CAM DECO 13M |
| 19 | R FLASH LENS | 20 | R CAM 13M LENS |
| 21 | REC | 22 | RF CABLE |
| 23 | BATTERY | 24 | MOTOR LINEA |
| 25 | PCBA SUB | 26 | PCBA COPPER B |
| 27 | EARPHONE RUBBER | 28 | SPK |
| 29 | USB RUBBER | 30 | PCBA COPPER A |
| 31 | SIDE KEY | 32 | SPK CON CLOTH |
| 33 | SCREW L3.2 | 34 | R CAM 13M CON FOAM |
| 35 | FP MYLAR | 36 | FP |
| 37 | R FLASH DECO | 38 | R CAM 8W DECO |
| 39 | R CAM 8W LENS |
Know your phone
- Front Camera
- Volume + key
- Volume – key
- Power key & side fingerprint sensor
SIM/SD card installation
- Power off mobile.
- Refer to the following picture for SIM / SD card installation.
Charging the phone
- You can charge your device using a charger or by connecting it to the computer using a USB cable (which comes with the phone).
- Use only the TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.
FCC
FCC Caution
Labeling requirements.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation Information to the user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Information to the user
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, under part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used by the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information
This mobile phone meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of the USA (FCC) is 1.6 W/kg averaging over one gram of tissue.
Device types: BG6s (FCC ID:2ADYY-BG6S) have also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.13 W/kg and when properly worn on the body is 0.72 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 1.0 cm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or approved antenna.
HiOS runs on AndroidTM OS.
Android is a trademark of Google LLC.
FAQ
- Q: Can I use any charger to charge my SPARK Go 2024?
- A: No, it is recommended to only use the TECNO charger and cables to avoid damaging the device and invalidating the warranty.
- Q: How do I install a SIM/SD card in the SPARK Go 2024?
- A: Make sure the mobile is powered off, then refer to the provided picture for proper installation steps.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>