Cameo CLMP10WRGB 5X5 10W RGB LED Matrix Panel User Manual
- June 10, 2024
- cameo
Table of Contents
USER´S MANUAL
MATRIX 300 RGB
LED MATRIX PANEL 5X5 10W RGB
CLMP10WRGB
YOU‘VE MADE THE RIGHT CHOICE!
We have designed this product to operate reliably over many years. Please read
this User‘s Manual carefully, so that you can begin making optimum use of your
Cameo Light product quickly. Learn more about Cameo Light on our website
WWW.CAMEOLIGHT.COM.
PREVENTIVE MEASURES
-
Please read these instructions carefully.
-
Keep all information and instructions in a safe place.
-
Follow the instructions.
-
Observe all safety warnings. Never remove safety warnings or other information from the equipment.
-
Use the equipment only in the intended manner and for the intended purpose.
-
Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain that wall mounts are properly installed andsecured. Make certain that the equipment is installed securely and cannot fall down.
-
During installation, observ e the applicable safety regulations for your country.
-
Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain that the equipment is always installed so that is cooled sufficiently and cannot overheat.
-
Never place sources of ignition, e.g., burning candles, on the equipment.
-
Ventilation slits must not be blocked.
-
This appliance is designed exclusively for indoor use, do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment – in this case, observe the special instructions noted below). Do not expose this equipment to flammable materials, fluids or gases.
-
Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with liquids, such as vases or drinking vessels, on the equipment.
-
Make certain that objects cannot fall into the device.
-
Use this equipment only with the accessories recommended and intended by the manufacturer.
-
Do not open or modify this equipment.
-
After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
-
During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries.
-
If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or if it has been damaged in anot her way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualified personnel.
-
Clean the equipment using a dry cloth.
-
Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.
-
Plastic bags must be kept out of reach of children.
FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS: -
CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.
-
If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature.
-
Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.
-
Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the mains outlet and/or power adapter and the equipment connector.
-
When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.
-
Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this can shorten the useful life of the equipment.
-
IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an authorised service centre.
-
To disconnect the equipment from the power mains completely, unplug the power cord or power adapter from the power outlet.
-
If your device is equipped with a Volex power connector, the mating Volex equipment connector must be unlocked before it can be removed. However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be careful when laying cables.
-
Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.
-
The device must only be installed in a voltage-free condition (disconnect the mains plug from the mains).
-
Dust and other debris inside the unit may cause damage. The unit should be regularly serviced or cleaned (no guarantee) depending on ambient conditions (dust etc., nicotine, fog) by qualified personnel to prevent overheating and malfunction.
-
Please keep a distance of at least 0.5 m to any combustible materials.
-
Power cables to power multiple devices must have a cross-section of at least 1.5 mm². Within the EU, the cables must correspond to H05VV-F, or similar. Suitable cables are offered by Adam Hall. With these cables, you can connect multiple devices via the power OUT connection to the power IN connection of an additional device. Make sure that the total current consumption of all connected devices does not exceed the specified value on all connected devices (label on the device). Make sure to keep power cable connections as short as possible.
CAUTION:
To reduce the risk of electric shock, do not remove cover (or back). There are
no user serviceable parts inside. Maintenance and repairs should be
exclusively carried out by qualified service personnel.
The warning triangle with lightning symbol indicates dangerous uninsulated
voltage inside the unit, which may cause an electrical shock.
The warning triangle with exclamation mark indicates important operating and
maintenance instructions.
The housing surface of the spotlight can heat up to temperatures as high as 70
°C in regular use. Ensure that it is not possible to come into contact with
the housing unintentionally. Always allow sufficient time for the lamp to cool
down before dismantling, carrying out maintenance work or charging etc.
Warning! This device is designed for use below 2000 metres in altitude.
Warning! This product is not intended for use in tropical climates.
Caution! Intense LED light source! Risk of eye damage. Do not look into the
light source.
CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS!
- The product has been developed for professional use in the field of event technology and is not suitable as household lighting.
- Do not stare, even temporarily, directly into the light beam.
- Do not look at the beam directly with optical instruments such as magnifiers.
- Stroboscope effects may cause epileptic seizures in sensitive people! People with epilepsy should definitely avoid places where strobes are used.
INTRODUCTION
LED MATRIX PANEL 5X5 10 W RGB
CLMP10WRGB
CONTROL FUNCTIONS
3-channel, 5-channel, 19-channel, 28-channel, 78-channel DMX control
Master/slave mode
Standalone function
FEATURES
Matrix panel with 25 x 10 W RGB LEDs. Single pixel control. 5 DMX modes.
DMX-512 control. Master/slave mode. Standalone programmes.
Sound control via built-in microphone. Safety eyelet and swivel bracket
included. 2 Omega mounting brackets included. Integrated connection system for
mounting an unlimited number of elements horizontally and up to five elements
vertically. Operating voltage 100-240 V AC/50-60 Hz. Power consumption 180 W.
CONNECTIONS, OPERATING AND DISPLAY ELEMENTS
-
POWER IN
Blue power input socket for power supply to the device. A suitable power cable is included. -
POWER OUT
White power output socket for the power supply of additional CAMEO spotlights. Ensure that the total current consumption of all connected devices does not exceed the value specified on the device in amperes (A). -
FUSE HOLDER
IMPORTANT: Replace the fuse only with a fuse of the same type and of the same value according to the stamp on the device! In the event ofrepeated fuse failure, please contact an authorised service centre. -
POWER
On/off switch. -
LED DISPLAY
The four-digit LED display shows the operating mode and other system information. -
OPERATING KEYS
MODE: Selection of the main menu items. Move up one level in the menu structure.
ENTER: Confirms programme selection and value changes.
UP and DOWN: Selection of operation mode and system settings, e.g. changing of microphone sensitivity and DMX address. -
MIC
Microphone for music control mode -
DMX IN
Male 3-pin XLR socket for connection to a DMX control device (e.g. DMX console). -
DMX OUT
Female 3-pin XLR socket for sending the DMX control signal. -
DMX IN
Male 5-pin XLR socket for connection to a DMX control device (e.g. DMX console). -
DMX OUT
Female 5-pin XLR socket for sending the DMX control signal. -
FAN
There are three case fans on the back of the device. Ensure that the fans are not covered and that air can circulate freely. -
VENTILATION SLITS
Ensure that the ventilation slits are not covered and that air can circulate freely. -
CARRY HANDLE
Two carry handles are provided at the back of the device so as to facilitate transport and mounting. -
SAFETY EYELET
An eyelet for a safety cable is to be found at the upper edge of the device at the back.
Overhead installation may only be carried out by qualified personnel. A suitable safety cable must be fitted to the eyelet to ensure that the spotlight does not fall down.
OPERATION
A few seconds after being switched on, the spotlight is ready for operation
and the previously selected operating mode is activated.
CONFIGURE DMX START ADDRESS
Press MODE repeatedly until “Addr” appears in the display. Now press ENTER and
configure the DMX start address using UP and DOWN as required (A001–A512).
Confirm your entry by pressing ENTER. For synchronous control of several
spotlights of the same model using a DMX device (e.g. DMX console), configure
the lights with identical DMX start addresses and the same DMX mode setting
and connect them using DMX cables. If there is no DMX signal, the display
characters will flash. Flashing stops as soon as a DMX signal is
present.
CONFIGURE DMX MODE
Press MODE repeatedly until “ChAn” appears in the display. Now press ENTER and
select the desired DMX mode using UP and DOWN as required (DMX 03Ch, 05Ch,
19Ch, 28Ch, 78Ch). Confirm your entry by pressing ENTER.
Tables with the channel assignment of the different DMX modes can be found in
these instructions under DMX CONTROL.
SLAVE MODE
Press MODE repeatedly until “SLAV” appears in the display and confirm by
pressing ENTER. Connect the slave and master units (same model)using a DMX
cable and enable the standalone mode SOUND CONTROL on the master unit. The
slave unit will now follow the master unit. If thereis no control signal, the
display characters will flash. Flashing stops as soon as a control signal is
present.
SOUND CONTROL MODE
Activate sound control mode to control the spotlight via the built-in
microphone (bass impulses) and set the microphone sensitivity as required.
Press MODE repeatedly until “SoUn” appears in the display and confirm by
pressing enter. Now use UP and DOWN to select “Soun”, press ENTER and then use
UP and DOWN again to select “on” or “oFF” to activate or deactivate sound
control. Confirm by pressing ENTER. Now use UP and DOWN to select “SenS”, the
menu item for microphone sensitivity, confirm by pressing ENTER and use UP and
DOWN to set the desired level (1 = minimum sensitivity, 99 = maximum
sensitivity). Confirm by pressing ENTER.
COLOUR BALANCE
Cross-mode calibration of colour reproduction with mixed colours. Press MODE
repeatedly until “baLa” appears in the display and confirm by pressing ENTER
Now select the colour whose intensity you wish to change using UP and DOWN
(red = red, Gree = green, bLue = blue) and confirmby pressing ENTER. Use UP
and DOWN once again to set the colour intensity from 0 to 255 and confirm by
pressing ENTER.
INVERTED DISPLAY
This function can be used to display letters, numbers and symbols
horizontally, vertically or horizontally and vertically inverted on the LED
matrix panel. Press MODE repeatedly until “Inve” appears in the display and
confirm by pressing enter. Now use UP and DOWN to select the desired option
and press ENTER to confirm.
SYSTEM SETTINGS AND SYSTEM INFORMATION
To adjust system settings and access system information, press MODE repeatedly
until “Sett” appears in the display. Confirm by pressing ENTER. You can now
use UP and DOWN to select and edit one of the following menu items:
MOUNTING
Single mounting in a traverse system is carried out using either a swivel
bracket (Fig. A) or two Omega mounting brackets (Fig. B). A swivel bracket and
two Omega mounting brackets are included, along with a set of screws and
U-discs and the tools required (1×5 mm and 1×6 mm hexagonal tool). In both
cases, ensure the brackets are firmly connected to the device, use appropriate
traverse mounting bolts (not included) and fit a suitable safety cable to the
eyelet to ensure the spotlight does not fall down (safety cable not included,
eyelet at rear of device). Important: Overhead installation may only be
carried out by qualified personnel.
The spotlight has an integrated connection system for mounting an unlimited
number of elements horizontally and up to five elements vertically. In order
to mount a group of spotlights created in this way in a system of traverses,
it is absolutely necessary to use two Omega mounting brackets for each top
element. For mechanical reasons, a group of spotlights may not be mounted on a
vertical traverse.
Each element is fitted with two connecting hooks on two sides and two
connecting bolts on two sides. In order to secur ely attach two elements, use
the 5 mm hexagonal tool to move the connecting hooks (Fig. C) into starting
position (turn as far as possible to the right). Join the elements in such a
way that the two recesses in the connecting hooks (Fig. C) of one element are
positioned precisely opposite the two recesses of the connecting bolts of the
other element (Fig. D). Now turn the connecting hooks anticlockwise using the
hexagonal tool as far as they will go (approx. 3/4 rotation) so that the
connecting hook firmly encloses the connecting bolt. Secure each element at
its eyelet by means of a suitable safety cable (safety cable not included).
For dismounting purposes, return the connecting hooks to starting position
(turn right as far as they will go). Important: Overhead installation may only
be carried out by qualified personnel.
DMX TECHNOLOGY
DMX-512
DMX (Digital Multiplex) is the designation for a universal transmission
protocol for communications between corresponding devices and controllers. A
DMX controller sends DMX data to the connected DMX device(s). The DMX data is
always transmitted as a serial data stream that is forwarded from one
connected device to the next via the “DMX IN” and “DMX OUT” connectors (XLR
plug-type connectors) that are found on every DMX-capable device, provided the
maximum number of devices does not exceed 32 units. The last device in the
chain needs to be equipped with a terminator (terminating resistor).
DMX CONNECTION
DMX is the common “language” via which a very wide range of types and models
of equipment from various manufacturers can be connected with one another and
controlled via a central controller, provided that all of the devices and the
controller are DMX compatible. For optimum data transmission, it is necessary
to keep the connecting cables between the individual devices as short as
possible. The order in which the devices are integrated in the DMX network has
no influence on the addresses. Thus the device with the DMX address 1 can be
located at any position in the (serial) DMX chain: at the beginning, at the
end or somewhere in the middle. If the DMX address 1 is assigned to a device,
the controller “knows” that it should send all data allocated to address 1 to
this device regardless of its position in the DMX network.
SERIAL CONNECTION OF MULTIPLE LIGHTS
- Connect the male XLR connector (3-pin or 5-pin) of the DMX cable to the DMX output (female XLR socket) of the first DMX device (e.g. DMX-Controller).
- Connect the female 3-pin XLR connector of the DMX cable connected to the first projector to the DMX input (male 3-pin socket) of the next DMX device. In the same way, connect the DMX output of this device to the DMX input of the next device and repeat until all devices have been connected. Please note that as a rule, DMX devices are connected in series and connections cannot be shared without active splitters. The maximum number of DMX devices in a DMX chain should not exceed 32 units.
The Adam Hall 3 STAR, 4 STAR, and 5 STAR product ranges include an extensive selection of suitable cables.
DMX CABLES
When fabricating your own cables, always observe the illustrations on this
page. Never connect the shielding of the cable to the ground contact of the
plug, and always make certain that the shielding does not come into contact
with the housing of the XLR plug. If the shielding is connected to the ground,
this can lead to short-circuiting and system malfunctions.
Pin Assignment
DMX TERMINATORS (TERMINATING RESISTORS)
To prevent system errors, the last device in a DMX chain needs to be equipped
with a terminating resistor (120 ohm, 1/4 Watt).
3-pin XLR connector with a terminating resistor: K3DMXT3
5-pin XLR connector with a terminating resistor: K3DMXT5
Pin Assignment
DMX ADAPTER
The combination of DMX devices with 3-pin connectors and DMX devices with
5-pin connectors in a DMX chain is possible with suitable adapters.
Pin Assignment
DMX Adapter 5-pin XLR male to 3-pin XLR female: K3DGF0020 Pins 4 and 5 are not
used.
Pin Assignment
DMX Adapter 3-pin XLR male to 5-pin XLR female: K3DHM0020 Pins 4 and 5 are not
used.
TECHNICAL DATA
| Model: | CLMP10WRGB |
|---|---|
| Product type: | LED MATRIX PANEL |
| Type: | 5X5 matrix |
| Colour spectrum: | RGB |
| Number of LEDs: | 25 |
| LED type: | 10 W Tri LED |
| Refresh rate: | 8000 Hz |
| Beam angle: | 40° |
| DMX input: | 3-pin and 5-pin male XLR |
| DMX output: | 3-pin and 5-pin female XLR |
| DMX mode: | 3-channel, 5-channel, 19-channel, 28-channel, 78-channel |
| DMX functions: | master dimmer, dimmer fine, auto programmes, sound programmes, |
stroboscope
Standalone functions:| sound control, master/slave
Control system| DMX512
Operating controls:| mode, enter, up, down
Display elements:| 4-digit LED display
Power connection:| blue mains input socket white power output socket
Operating voltage:| 100-240 V AC/50-60 Hz
Power consumption:| 180 W
Light intensity (@ 1 m):| 6950 lx (full on)
Fuse:| T3AL/250 V (5 x 20mm)
Ambient temperature (in operation):| 10°C-40°C
Relative air humidity:| <85%, non-condensing
Housing material:| metal
Housing colour:| black
Housing cooling:| convection
Dimensions (W x H x D, without bracket):| 580 x 580 x 125 mm
Weight (not incl. brackets):| 13.7 kg
Additional features:| adjustable swivel bracket including two Omega mounting
brackets, safety eyelet, integrated connection system for mounting an
unlimited number of elements horizontally and up to five elements vertically
MANUFACTURER´S DECLARATIONS
MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY
You can find our current warranty conditions and limitations of liability at:
https://cdn-shop.adamhall.com/media/pdf/Manufacturers-Declarations-
CAMEO_DE_EN_ES_FR.pdf.
To request warranty service for a product, please contact Adam Hall GmbH,
Daimler Straße 9, 61267 Neu Anspach /
Email: Info@adamhall.com / +49 (0)6081 /9419-0.
CORRECT DISPOSAL OF THIS PRODUCT
**** (valid in the European Union and other European countries with a
differentiated waste collection system)
This symbol on the product, or on its documents indicates that the device may
not be treated as household waste. This is to avoid environmental damage or
personal injury due to uncontrolled waste disposal. Please dispose of this
product separately from other waste and have it recycled to promote
sustainable economic activity. Household users should contact either the
retailer where they purchased this product, or their local government office,
for details on where and how they can recycle this item in an environmentally
friendly manner. Business users should contact their supplier and check the
terms and conditions of the purchase contract. This product should not be
mixed
with other commercial waste for disposal.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesired operation
CE Compliance
Adam Hall GmbH states that this product meets the following guidelines (where
applicable):
R&TTE (1999/5/EC) or RED (2014/53/EU) from June 2017
Low voltage directive (2014/35/EU)
EMV directive (2014/30/EU)
RoHS (2011/65/EU)
The complete declaration of conformity can be found at
www.adamhall.com.
Furthermore, you may also direct your enquiry to
info@adamhall.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>