cameo CLH1 Wall Mount Instruction Manual
- June 4, 2024
- cameo
Table of Contents
cameo CLH1 Wall Mount
PRODUCT INFORMATION
This item is a product-specific accessory intended exclusively for use with
Cameo H1 series spotlights.
These installation instructions do not replace the user manual of the
associated product. Always read the relevant user manual first. This accessory
has no influence on the intended use of the associat-ed product.
Observe the safety instructions in the user manual of the associated product!
The technical data given in the user manual may change in connection with this
accessory.
SAFETY INSTRUCTIONS
- Please read this manual carefully.
- Keep all information and instructions in a safe place.
- Follow the instructions.
- Use the accessory in the prescribed manner only.
HAZARD: KEEP OUT OF THE REACH OF CHILDREN! THE PRODUCT CONTAINS SMALL PARTS THAT CAN BE SWALLOWED AS WELL AS PACKAGING MATERIAL THAT CAN BE SWALLOWED! PLASTIC BAGS MUST BE KEPT OUT OF THE REACH OF CHILDREN!
INCLUDED
Remove the product from the packaging and remove all packaging material.
Please check the completeness and integrity of the delivery and notify your
distribution partner immediately after purchase if the delivery is not
complete or if it is damaged.
Product includes: 
- 1 x wall mounting plate
- 1 x connecting element
- 4 x fixing screw M4 x 18 plus washers
- 1 x locking screw M4 x 18 plus washer
- 1 x cover cap
- 2 x long covering rail
Installation instructions
MOUNTING
The spotlight can be mounted on a wall using the wall mounting kit, either as
an uplight or rotated through 180° as a downlight.
Before installation, ensure that the spotlight is completely discon-nected
from the power supply and that the power supply cable is free from voltage.
Check that the connections are secure during all assembly steps!
- Using suitable fixing materials, mount the wall mounting plate A on a suitable wall in the desired position with the 4 mounting hooks A-1 pointing vertically upwards. The cables for the power and signal supply can be fed through various openings in the plate.
- Using a suitable tool, loosen the 4 screws from the end ring on the back of the spotlight and remove the end ring.
- Loosen the mounting bracket with the sockets from the spotlight as described in the H1 spotlight instructions and remove the 4 short cover rails from the side slots.
- Remove the long cover rail from slot G. The 4 threads in the slot for fastening connecting element B to the spotlight are now exposed.
- Fasten the connecting element B to the spotlight using the 4 enclosed screws and washers C.
- Feed the cables for the power and signal supply through the cor-responding opening in the connecting element (see arrow).
- Guide the spotlight and connecting element from above onto the wall mounting plate and press it downwards. Ensure that the mounting hooks A-1 on the wall mounting plate engage securely in the corresponding lugs on the connecting element. Now secure the connection with the enclosed locking screw and washer D.
- Remove the terminal cover from the spotlight and connect the ca-bles for the power and signal supply as described in the instructions for the H1 spotlight.
- Insert the long cover rails F into the side slots for the cover of the U-bolt connection.
- Place the cover cap E with the recess facing the connecting el-ement on the rear of the spotlight and fasten it with 3 of the screws previously loosened from the end ring.
When installing as an uplight, make sure that the cover rails do not fall out of the respective slots, as they are not secured by the end ring or the cover cap during installation. Tip: Secure the rails during installation using an adhesive strip that can be removed without leaving any residue.
TECHNICAL DATA
DISPOSAL
Packaging:
- Packaging can be fed into the reusable material cycle using the usual disposal methods.
- Please separate the packaging in accordance with the disposal laws and recycling regulations in your country.
Product:
Dispose of the product in accordance with the applicable disposal regulations
in your country.
MANUFACTURER’S DECLARATIONS
MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY
Adam Hall GmbH, Adam-Hall-Str. 1, D-61267 Neu Anspach /
E-mail Info@adamhall.com / +49 (0)6081 / 9419-0.
For details of our current warranty conditions and limitation of liability,
see:
https://cdn-shop.adamhall.com/media/pdf/Manufacturers-Declarations-
CAMEO_DE_EN_ES_FR.pdf
If you require service, please contact your distribution partner.
UKCA CONFORMITY
Adam Hall GmbH hereby declares that this product complies with the following
directives (where applicable): R&TTE (1999/5/EC) or RED (2014/53/EU) as of
June 2017
Low Voltage Directive (2014/35/EU)
EMC Directive (2014/30/EU)
RoHS (2011/65/EU) The declaration of conformity
can be found at www.adamhall.com.
You can also request it via info@adamhall.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>