Cameo CLH1CKB H1 Ceiling Kit Instruction Manual
- June 8, 2024
- cameo
Table of Contents
INSTALLATION INSTRUCTIONS
H1 CEILING KIT
CEILING KIT FOR H1 SERIES BLACK OR WHITE
PRODUCT INFORMATION
This item is a product-specific accessory intended exclusively for use with
Cameo H1 series spotlights.
These installation instructions do not replace the user manual of the
associated product. Always read the relevant user manual first.
This accessory has no influence on the intended use of the associated product.
Observe the safety instructions in the user manual of the associated product!
The technical data given in the user manual may change in connection with this
accessory.
SAFETY INSTRUCTIONS
- Please read this manual carefully.
- Keep all information and instructions in a safe place.
- Follow the instructions.
- Use the accessory in the prescribed manner only.
- While installing the spotlight, be aware of heat accumulation.
HAZARD: KEEP OUT OF THE REACH OF CHILDREN! THE PRODUCT CONTAINS SMALL PARTS THAT CAN BE SWALLOWED AS WELL AS PACKAGING MATERIAL THAT CAN BE SWALLOWED! PLASTIC BAGS MUST BE KEPT OUT OF THE REACH OF CHILDREN!
INCLUDED
Remove the product from the packaging and remove all packaging material.
Please check the completeness and integrity of the delivery and notify your
distribution partner immediately after purchase if the delivery is not
complete or if it is damaged.
Product includes:
A. 1x mounting ring
B. 2x mounting brackets
C. 4x M4 fixing screws with washer and lock washer for the mounting brackets
D. 4x M4 fixing screws for the mounting ring Installation instructions
DIMENSIONS (mm)
|
---|---
INSTALLATION
- Before mounting, ensure that the spotlight is completely disconnected from the power supply.
- Place the mounting ring (A) from below into the already prepared cut-out in a suitable ceiling construction (for hole diameter, see illustrations DIMENSIONS). Screw the two mounting brackets (B) on opposite sides of the mounting ring. To do so, use 2 screws with lock washers and washer (C) each, selecting the two upper screw holes in the mounting ring (see markings). The mounting brackets each have a slotted hole, so that the mounting ring can be fastened to the ceiling element without any play.
- Now place the spotlight into the mounting ring from above, making sure that the 4 guide rails on the inside of the mounting ring engage in the 4 grooves of the spotlight. Thickening at the lower end of the guide rails prevents the spotlight from sliding through the mounting ring.
- Now secure the spotlight to the mounting ring. To do so, use 2 screws (D) on the opposite sides of the mounting ring and select the upper and lower screw holes (see markings).
TECHNICAL DATA
| PRODUCT NUMBER: | CLZH1CK(B/W) |
|---|---|
| Product type: | Spotlight accessory |
| Type: | Ceiling installation kit for Cameo H1 series |
| Material: | Metal |
| Colour: | Black (CLH1CKB) |
White (CLH1CKW)
Dimensions of mounting ring
(Ø x H):| 166 x 55 mm
Weight:| 0.385 kg
DISPOSAL
Packaging:
- Packaging can be fed into the reusable material cycle using the usual disposal methods.
- Please separate the packaging in accordance with the disposal laws and recycling regulations in your country.
Product:
Dispose of the product in accordance with the applicable disposal regulations
in your country.
MANUFACTURER’S DECLARATIONS
MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY
Adam Hall GmbH, Adam-Hall-Str. 1, D-61267 Neu Anspach /E-mail
[email protected] / +49 (0)6081 / 9419-0.
For details of our current warranty conditions and limitation of liability,
see: https://cdn-shop.adamhall.com/media/pdf/Manufacturers-Declarations-
CAMEO_DE_EN_ES_FR.pdf
If you require service, please contact your distribution partner.
UKCA CONFORMITY
Adam Hall GmbH hereby declares that this product complies with the following
directives (where applicable):
R&TTE (1999/5/EC) or RED (2014/53/EU) as of June 2017
Low Voltage Directive (2014/35/EU)
EMC Directive (2014/30/EU)
RoHS (2011/65/EU) The declaration of conformity can be found at
www.adamhall.com.
You can also request it via [email protected]
Subject to misprints and errors, as well as technical or other modifications!
Cameo® is a registered brand of the Adam Hall Group
Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu Anspach | Germany
Phone: +49 6081 9419-0 | adamhall.com