cameo CLHB4000RGBW 4 Head Moving Bar Hydrabeam 4000 User Manual
- June 6, 2024
- cameo
Table of Contents
Colours of light
USER´S MANUAL
4 HEAD MOVING BAR HYDRABEAM 4000 CLHB4000RGBW
YOU‘VE MADE THE RIGHT CHOICE!
We have designed this product to operate reliably over many years. Please read
this User‘s Manual carefully, so that you can begin making optimum use of your
Cameo Light product quickly. Learn more about Cameo Light on our website WWW.
CAMEOLIGHT.COM.
PREVENTIVE MEASURES
-
Please read these instructions carefully.
-
Keep all information and instructions in a safe place.
-
Follow the instructions.
-
Observe all safety warnings. Never remove safety warnings or other information from the equipment.
-
Use the equipment only in the intended manner and for the intended purpose.
-
Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain that wall mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.
-
During installation, observ e the applicable safety regulations for your country.
-
Never install and operate the equipment near radiators, heat registers, ovens, or other sources of heat. Make certain that the equipment is always installed so that is cooled sufficiently and cannot overheat.
-
Never place sources of ignition, e.g., burning candles, on the equipment.
-
Ventilation slits must not be blocked.
-
Keep a minimum distance of 20 cm around and above the device.
-
Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment – in this case, observe the special instructions noted below. Do not expose this equipment to flammable materials, fluids or gases. Avoid direct sunlight!
-
Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with liquids, such as vases or drinking vessels, on the equipment.
-
Make certain that objects cannot fall into the device.
-
Use this equipment only with the accessories recommended and intended by the manufacturer.
-
Do not open or modify this equipment.
-
After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
-
During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries.
-
If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or if it has been damaged in her way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualified personnel.
-
Clean the equipment using a dry cloth.
-
Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.
-
Plastic bags must be kept out of reach of children.
-
Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.
FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS: -
CAUTION: If the power cord of the device is equipped with earthing contact, then it must be connected to an outlet with a protective
ground. Never deactivate the protective ground of a power cord. -
If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature.
-
Before connecting the equipment to the power outlet, first, verify that the mains voltage and frequency match the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or the power adapter does not fit in your wall outlet, contact your electrician.
-
Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the main outlet and/or power adapter and the equipment connector.
-
When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.
-
Whenever possible, avoid switching the equipment on and off in quick succession because otherwise, this can shorten the useful life of the equipment.
-
IMPORTANT INFORMATION : Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an authorized service center.
-
To disconnect the equipment from the power mains completely, unplug the power cord or power adapter from the power outlet
-
If your device is equipped with a Volex power connector, the mating Volex equipment connector must be unlocked before it can be removed. However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be careful when laying cables.
-
Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.
-
The device must only be installed in a voltage-free condition (disconnect the mains plug from the mains).
-
Dust and other debris inside the unit may cause damage. The unit should be regularly serviced or cleaned (no guarantee) depending on ambient conditions (dust etc., nicotine, fog) by qualified personnel to prevent overheating and malfunction.
-
Please keep a distance of at least 0.5 m to any combustible materials.
-
Power cables to power multiple devices must have a cross-section of at least 1.5 mm². Within the EU, the cables must correspond to H05VV-F, or similar. Suitable cables are offered by Adam Hall. With these cables, you can connect multiple devices via the power OUT connection to the power IN connection of an additional device. Make sure that the total current consumption of all connected devices does not exceed the specified value on all connected devices (label on the device). Make sure to keep power cable connections as short as possible.
CAUTION:
To reduce the risk of electric shock, do not remove the cover (or back). There
are no user-serviceable parts inside. Maintenance and repairs should be
exclusively carried out by qualified service personnel.
| The warning triangle with the lightning symbol indicates
dangerous uninsulated voltage inside the unit, which may cause an electrical
shock.
---|---
The warning triangle with an exclamation mark indicates important operating
and maintenance instructions.
Warning! This symbol indicates a hot surface. Certain parts of the housing can
become hot during operation. After use, wait for a cool-down period of at
least 10 minutes before handling or transporting the device.
Warning! This device is designed for use below 2000 meters in altitude.
Warning! This product is not intended for use in tropical climates.
CAUTION! HIGH VOLUMES IN AUDIO PRODUCTS!
This device is meant for professional use. Therefore, commercial use of this
equipment is subject to the respectively applicable national accident
prevention rules and regulations. As a manufacturer, Adam Hall is obligated to
notify you formally about the existence of potential health risks.
Hearing damage due to high volume and prolonged exposure: When in use, this
product is capable of producing high sound-pressure levels (SPL) that can lead
to irreversible hearing damage in performers, employees, and audience members.
For this reason, avoid prolonged exposure to volumes in excess of 90 dB.
INTRODUCTION
4 HEAD MOVING BAR HYDRABEAM 4000
CLHB4000RGBW
CONTROL FUNCTIONS
6-channel, 10-channel, 19-channel, 32-channel, 56-channel DMX control
Master/slave mode
Standalone operation
FEATURES
4 ultra-fast and individually-controlled moving heads. 4 high-performance 32 W
RGBW Quad LEDs 5 DMX modes. DMX-512 control. Master/slave mode. Standalone
programs. Sound control via built-in microphone. Universal mounting options. 2
Omega brackets and a tripod flange included. Operating voltage 100 – 240 V AC
/ 50 – 60 Hz. Power consumption 220 W
OPERATION
The Cameo Hydrabeam 4000 RGBW is a DMX-512-controllable 4-piece LED moving
head that can be used as a standalone unit, in master /slave mode, or operated
by sound control.
CONNECTIONS, OPERATING, AND DISPLAY ELEMENTS
-
POWER IN
Blue power input socket for power supply to the device. A suitable power cable is included. -
POWER OUT
White power output socket for power supply to additional CAMEO lights. Ensure that the total current consumption of all connected devices does not exceed the value specified on the device in amperes (A). -
FUSE
Fuse holder with F3AL / 250 V fuse (5 x 20 mm). IMPORTANT: When replacing the fuse, only use a fuse of the same type and value. In the event of repeated fuse failure, please contact an authorized service center. -
POWER
On / off switch. -
DMX IN
Male 3-pin and 5-pin XLR sockets for connection to a DMX control device (e.g. DMX console). -
DMX OUT
Female 3-pin and 5-pin XLR socket for sending the DMX control signal. -
LC DISPLAY
The LED display shows the operating mode and other system information. -
OPERATING KEYS
MENU
Press MENU to access the selection menu for system settings. Press repeatedly to go back to the main display.
UP and DOWN
Select individual items in the selection menu and sub-menus for system settings (DMX address, operating mode, etc.). Change settings in the menu items.
ENTER
Press ENTER to access the menu levels and change values as required, e.g. the DMX address. Confirm value changes. -
EYELET FOR SAFETY CABLE
Overhead installation may only be carried out by qualified personnel. A suitable safety cable must be fitted to the floodlight’s eyelet to ensure that it does not fall down.
OPERATION
NOTE
When the lamp is correctly connected to the mains supply and the standby
switch is on, the CAMEO logo is shown on the display during start-up and motor
reset. Once this process is complete, the spotlight is ready for operation and
the previously selected operating mode is activated.
CONFIGURE DMX START ADDRESS
Press MENU to access the selection menu for system settings. Select the menu
item “DMX Address” (shaded in color) using UP and DOWN and confirm with
entering. A number field is now displayed and you can set the DMX start
address as required, from 001 to 512, using the UP and DOWN buttons (hold down
the button to change values quickly). Confirm with entering and press MENU to
return to the main display. After approx. one minute of no input, the main
display is automatically activated, the DMX start address is shown clearly at
the center of the display and the DMX mode appears in the bottom line (6Ch,
10Ch, 19Ch, 32Ch, 56Ch).
CONFIGURE DMX MODE
Press MENU to access the selection menu for system settings. Select the menu
item “DMX Mode” (shaded in color) using UP and DOWN and confirm with entering.
A selection field is then displayed and you can set the desired DMX mode using
the UP and DOWN buttons. Confirm with entering and press MENU to return to the
main display. After approx. one minute of no input, the main display is
automatically activated, the DMX start address is shown clearly at the center
of the display and the DMX mode appears in the bottom line (6Ch, 10Ch, 19Ch,
32Ch, 56Ch).
CONFIGURE AUTO MODE
The 17 available auto programs each consist of a series of non-editable color-
change and motion sequences. Press MENU to access the selection menu for
system settings. Select the menu item “Auto Mode” (shaded in color) using UP
and DOWN, and confirm with entering. Select the menu item “Show Mode” using
the UP and DOWN buttons, confirm with entering, then select the required
program, Auto0 to Auto16, using UP and DOWN again, then confirm with entering.
You can set the program speed by selecting the menu item “Show Speed” using
the UP and DOWN buttons, confirming with entering, and then using UP and DOWN
once again to select a value between 01 and 99 (hold button down to change
values quickly, 01 = minimum and 99 = maximum speed). Confirm with ENTER and
press MENU twice to return to the main display. After approx. one minute of no
input, the main display is automatically activated and the selected auto
program is shown clearly at the center of the display.
ACTIVATE SOUND CONTROL
Select one of the auto programs as described above under CONFIGURE AUTO MODE.
Now select the menu item “Sound Mode” (shaded in color) using UP and DOWN,
confirm with entering, then use UP and DOWN again to select “On” and confirm
with entering. You can set the microphone sensitivity by selecting the menu
item “Sound Sens” using the UP and DOWN buttons, confirming with entering and
then using UP and DOWN once again to select a value between 00 and 99 (hold
button down to change values quickly, 00 = minimum and 99 = maximum
sensitivity). Confirm with entering and press MENU twice to return to the main
display. After approx. one minute of no input, the main display is
automatically activated and the selected sound program is shown clearly at the
center of the display. Now the spotlight is controlled via the built-in
microphone and follows the beat of the music (bass impulses).
SLAVE MODE
Press MENU to access the selection menu for system settings. Select the menu
item “Slave Mode” (shaded in color) using UP and DOWN, and confirm with
entering. Press MENU to return to the main display. After approx. one minute
of no input, the main display is automatically activated and SLAVE is shown
clearly at the center of the display. Connect the slave and the master units
(same model) with a DMX cable, and enable one of the standalone modes on the
master unit (Auto, Sound). The slave unit will now follow the master unit.
ADVANCED SETTINGS
Press MENU to access the selection menu for system settings. Select the menu
item “Advanced Settings” (shaded in color) using UP and DOWN, and confirm with
entering. This will take you to the sub-menu for configuring the following
sub-menu items (selecting using UP and DOWN, confirm with entering):
Advanced Settings
Reset| =| Reset motors| Yes.| Reset pan and tilt motors
No| = Discontinue pan and tilt motor reset
Pan Invert| =| Head pan direction| No| = No reversal of pan direction
Head2 pan direction
Head3 pan direction| Yes.| = Reversal of pan direction
Head4 pan direction
Tilt Invert| =| Head1 tilt direction| No| = No reversal of tilt direction
Head2 tilt direction
Head3 tilt direction| Yes.| = Reversal of tilt direction
Head4 tiff direction
Display| =| Display lighting| On| = Permanently on
Off| = Deactivation after one minute of inactivity
Display invert| =| Rotate display| On| = Rotate display by 180°
(e.g. for overhead installation)
Off| = No display rotation
DMX Fall| =| Operating status with DMX signal fault| Auto| = Activates auto
mode
Black| = Activates blackout
Hold| = Last command is retained
Software| =| Display device software| ENTER| Vl.x
INSTALLATION
Thanks to its integrated rubber feet, the spotlight can be positioned in a
suitable location on the stage floor, etc. Installation on a traverse is
possible using the two Omega brackets supplied (only use original accessories)
together with the appropriate traverse clamps (not included). Attach the
device securely at the specified position using a suitable safety cable.
Important: Overhead installation may only be carried out by qualified
personnel. Installation on a suitable tripod is possible using the integrated
35 mm tripod flange.
DMX TECHNOLOGY
DMX-512
DMX (Digital Multiplex) is the designation for a universal transmission
protocol for communications between corresponding devices and controllers. A
DMX controller sends DMX data to the connected DMX device(s). The DMX data is
always transmitted as a serial data stream that is forwarded from one
connected device to the next via the “DMX IN” and “DMX OUT” connectors (XLR
plug-type connectors) that are found on every DMX-capable
device provided the maximum number of devices does not exceed 32 units. The
last device in the chain needs to be equipped with a terminator (terminating
resistor).
DMX CONNECTION
DMX is the common “language” via which a very wide range of types and models
of equipment from various manufacturers can be connected with one another and
controlled via a central controller, provided that all of the devices and the
controller are DMX compatible. For optimum data transmission, it is necessary
to keep the connecting cables between the individual devices as short as
possible. The order in which the devices are integrated into the DMX network
has no influence on the addresses. Thus the device with the DMX address 1 can
be located at any position in the (serial) DMX chain: at the beginning, at the
end, or somewhere in the middle. If DMX address 1 is assigned to a device, the
controller “knows” that it should send all data allocated to address 1 to this
device regardless of its position in the DMX network.
SERIAL CONNECTION OF MULTIPLE LIGHTS
- Connect the male XLR connector (3-pin or 5-pin) of the DMX cable to the DMX output (female XLR socket) of the first DMX device (e.g. DMX-Controller).
- Connect the female 3-pin XLR connector of the DMX cable connected to the first projector to the DMX input (male 3-pin socket) of the next DMX device. In the same way, connect the DMX output of this device to the DMX input of the next device and repeat until all devices have been connected. Please note that as a rule, DMX devices are connected in series and connections cannot be shared without active splitters. The maximum number of DMX devices in a DMX chain should not exceed 32 units. The Adam Hall 3 STAR, 4 STAR, and 5 STAR product ranges include an extensive selection of suitable cables.
DMX CABLES
When fabricating your own cables, always observe the illustrations on this
page. Never connect the shielding of the cable to the ground contact of the
plug, and always make certain that the shielding does not come into contact
with the housing of the XLR plug. If the shielding is connected to the ground,
this can lead to short-circuiting and system malfunctions.
DMX TERMINATORS (TERMINATING RESISTORS)
To prevent system errors, the last device in a DMX chain needs to be equipped
with a terminating resistor (120 ohms, 1/4 Watt).
3-pin XLR connector with a terminating resistor: K3DMXT3
5-pin XLR connector with a terminating resistor: K3DMXT5 
DMX ADAPTER
The combination of DMX devices with 3-pin connectors and DMX devices with
5-pin connectors in a DMX chain is possible with suitable adapters.
Pin Assignment
DMX Adapter 5-pin XLR male to 3-pin XLR female: K3DGF0020 Pins 4 and 5 are not
used.
Pin Assignment
DMX Adapter 3-pin XLR male to 5-pin XLR female: K3DHM0020 Pins 4 and 5 are not
used.
TECHNICAL DATA
| Model name: | CLHB4000RGBW |
|---|---|
| Product Type: | LED moving lights |
| Type: | Moving head bar |
| Color spectrum: | RGBW |
| No. of LEDs: | 4 |
| LED type: | 32 W quad |
| Dispersion angle: | 2.5° |
| DMX input: | 3-pin male XLR |
| DMX output: | 3-pin female XLR |
| DMX mode: | 6-channel, 10-channel, 19-channel, 32-channel, 56-channel |
| DMX functions: | Pan/tilt, pan/tilt fine, single head control, auto programs, |
sound control, color
macros, stroboscope, dimmer
Standalone functions:| Auto programs, sound control, master/slave
Control:| USITT DMX512
Operating controls:| MENU, ENTER, UP, DOWN
Indicators:| 4-digit LED display
PAN angle:| 540°
TILT angle:| 270°
Operating voltage:| 100 – 240 V AC / 50 – 60 Hz.
Power consumption:| 220 W
Light intensity (@ 1 m):| Single Head R: 17900, G: 42400, B: 9600, W: 67200 lx
Mains input socket:| Blue power twist connector
Mains output socket:| White power twist connector
Fuse:| F3AL/250 V (5 x 20 mm)
Ambient temperature (for operation):| 0 °C – 40 °C
Relative air humidity:| < 80%, non-condensing
Housing material:| Metal, ABS
Housing color:| Black
Housing cooling:| Low-noise fan
Dimensions (W x H x D, not including mounting
bracket):| 1000 x 270 x 90 mm
Weight:| 12 kg
Additional features:| Power cable, 35 mm tripod flange, and Omega mounting
bracket included
MANUFACTURER´S DECLARATIONS
MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY
You can find our current warranty conditions and limitations of liability at:
http://www.adamhall.com/media/shop/downloads/documents/manufacturersdeclarations.pdf.
To request warranty service for a product, please contact Adam Hall GmbH,
Daimler Straße 9, 61267 Neu Anspach / Email:
Info@adamhall.com / +49 (0)6081 / 9419-0.
CORRECT DISPOSAL OF THIS PRODUCT
(valid in the European Union and other European countries with a
differentiated waste collection system)
This symbol on the product, or on its documents indicates that the device may
not be treated as household waste. This is to avoid environmental damage or
personal injury due to uncontrolled waste disposal. Please dispose of this
product separately from other waste and have it recycled to promote
sustainable economic activity. Household users should contact either the
retailer where they purchased this product, or their local government office,
for details on where and how they can recycle this item in an environmentally
friendly manner. Business users should contact their suppliers and check the
terms and conditions of the purchase contract. This product should not be
mixed with other commercial waste for disposal.
CE Compliance
Adam Hall GmbH states that this product meets the following guidelines (where
applicable):
R&TTE (1999/5/EC) or RED (2014/53/EU) from June 2017
Low voltage directive (2014/35/EU)
EMV directive (2014/30/EU)
RoHS (2011/65/EU)
The complete declaration of conformity can be found at
www.adamhall.com.
Furthermore, you may also direct your inquiry to
info@adamhall.com.
DMX CONTROL
6-CH Mode
CH1| master dimmer| 000| –| 255| 0-100%
CH2| strobe| 000| –| 010| no strobe
011| –| 255| slow to fast
CH3
| ****
show mode
| 000| –| 007| no movement
008| –| 022| show mode 1
023| –| 037| show mode 2
038| –| 052| show mode 3
053| –| 067| show mode 4
068| –| 082| show mode 5
083| –| 097| show mode 6
098| –| 112| show mode 7
113| –| 127| show mode 8
128| –| 142| show mode 9
143| –| 157| show mode 10
158| –| 172| show mode 11
173| –| 187| show mode 12
188| –| 202| show mode 13
203| –| 217| show mode 14
218| –| 232| show mode 15
233| –| 247| show mode 16
248| –| 255| sound control mode
CH4| 000| –| 255| show mode speed (slow to fast) / sound sensitivity
CH5| ****
light control
| 000| –| 030| automatic color change
031| –| 255| color macro (see color macro table)
CH6| 000| –| 255| automatic color change speed
10-CH Mode
CH1| ****
master control
| 000| –| 255| pan
CH2| 000| –| 255| tilt
CH3| 000| –| 255| master dimmer 0-100%
CH4| strobe| 000| –| 010| no strobe
011| –| 255| slow to fast
colour macro:
031 – 045| R
046 – 060| G
061 – 075| B
076 – 090| W
091 – 105| RG
106 – 120| RB
121 – 135| RW
136 – 150| GB
151 – 165| GW
166 – 180| BW
181 – 195| RGB
196 – 210| RGW
211 – 225| RBW
226 – 240| GBW
241 – 255| RGBW
CH5
| ****
show mode
| 000| –| 007| no movement
---|---|---|---|---|---
008| –| 022| show mode 1
023| –| 037| show mode 2
038| –| 052| show mode 3
053| –| 067| show mode 4
068| –| 082| show mode 5
083| –| 097| show mode 6
098| –| 112| show mode 7
113| –| 127| show mode 8
128| –| 142| show mode 9
143| –| 157| show mode 10
158| –| 172| show mode 11
173| –| 187| show mode 12
188| –| 202| show mode 13
203| –| 217| show mode 14
218| –| 232| show mode 15
233| –| 247| show mode 16
248| –| 255| sound control mode
CH6| 000| –| 255| show mode speed (slow to fast) / sound sensitivity
CH7| ****
light control
| 000| –| 030| automatic color change
031| –| 255| color macro (see color macro table)
CH8| 000| –| 255| automatic color change speed (slow to fast )
CH9| fine control| 000| –| 255| pan fine
CH10| 000| –| 255| tilt fine
19-CH Mode
CH1| master dimmer| 000| –| 255| master dimmer 0-100%
CH2| strobe| 000| –| 010| no strobe
011| –| 255| slow to fast
CH3| ****
colour control
| 000| –| 255| red dimmer
CH4| 000| –| 255| green dimmer
CH5| 000| –| 255| blue dimmer
CH6| 000| –| 255| white dimmer
CH7| ****
first head
| 000| –| 255| pan
CH8| 000| –| 255| tilt
CH9| 000| –| 255| dimmer 0-100%
CH10| ****
second head
| 000| –| 255| pan
CH11| 000| –| 255| tilt
CH12| 000| –| 255| dimmer 0-100%
CH13| ****
third head
| 000| –| 255| pan
CH14| 000| –| 255| tilt
CH15| 000| –| 255| dimmer 0-100%
CH16| ****
fourth head
| 000| –| 255| pan
CH17| 000| –| 255| tilt
CH18| 000| –| 255| dimmer 0-100%
CH19| head speed| 000| –| 255| fast to slow
32-CH Mode
CH1| master dimmer| 000| –| 255| dimmer 0-100%
CH2| strobe| 000| –| 010| no strobe
011| –| 255| slow to fast
CH3| ****
first head
| 000| –| 255| first head, pan
CH4| 000| –| 255| first head, pan fine
CH5| 000| –| 255| first head, tilt
CH6| 000| –| 255| first head, tilt fine
CH7
| 000| –| 010| first head speed (fastest value until DMX-value 011 is reached)
011| –| 255| first head speed, fast to slow
CH8
| 000| –| 030| use CH29-CH32 to control color
031| –| 255| the first head, color macro (see color macro table)
CH9| ****
second head
| 000| –| 255| the second head, pan
CH10| 000| –| 255| the second head, pan fine
CH11| 000| –| 255| the second head, tilt
CH12| 000| –| 255| the second head, tilt fine
CH13
| 000| –| 010| second head speed, use speed value from CH7
011| –| 255| second head speed, fast to slow
CH14
| 000| –| 030| use CH29-CH32 to control color
031| –| 255| the second head, color macro (see color macro table)
CH15| ****
third head
| 000| –| 255| third head, pan
CH16| 000| –| 255| third head, pan fine
CH17| 000| –| 255| third head, tilt
CH18| 000| –| 255| third head, tilt fine
CH19| 000| –| 010| third head speed, use speed value from CH7
011| –| 255| third head speed, fast to slow
CH20
| 000| –| 030| use CH29-CH32 to control color
031| –| 255| the third head, color macro (see color macro table)
CH21| ****
fourth head
| 000| –| 255| fourth head, pan
CH22| 000| –| 255| fourth head, pan fine
CH23| 000| –| 255| fourth head, tilt
CH24| 000| –| 255| fourth head, tilt fine
CH25
| 000| –| 010| fourth head speed, use speed value from CH7
011| –| 255| fourth head speed, fast to slow
CH26
| 000| –| 030| use CH29-CH32 to control color
031| –| 255| fourth head, color macro (see color macro table)
CH27
| ****
sound mode/reset
| 000| –| 199| no function
200| –| 209| reset
210| –| 240| no function
241| –| 255| sound control mode
CH28| 000| –| 255| sound sensitivity in sound mode
CH29| ****
master color selection
| 000| –| 255| red dimmer
CH30| 000| –| 255| green dimmer
CH31| 000| –| 255| blue dimmer
CH32| 000| –| 255| white dimmer
colour macro:
031 – 045| R
046 – 060| G
061 – 075| B
076 – 090| W
091 – 105| RG
106 – 120| RB
121 – 135| RW
136 – 150| GB
151 – 165| GW
166 – 180| BW
181 – 195| RGB
196 – 210| RGW
211 – 225| RBW
226 – 240| GBW
241 – 255| RGBW
56-CH Mode
CH1| ****
mechanic control
| 000| –| 255| pan| ****
Head 1
CH2| 000| –| 255| pan fine
CH3| 000| –| 255| tilt
CH4| 000| –| 255| tilt fine
CH5| 000| –| 255| head speed, fast to slow
CH6| dimmer| 000| –| 255| dimmer, 0% – 100%
CH7| strobe| 000| –| 010| no-strobe
011| –| 255| slow to fast
CH8
| | 000| –| 030| use CH11-CH14 to control color
031| –| 255| color macro
(see color macro table)
CH9
| ****
auto mode / sound mode / reset
| 000| –| 007| no function
008| –| 030| show mode 1
031| –| 053| show mode 2
054| –| 076| show mode 3
077| –| 099| show mode 4
100| –| 122| sound control mode
123| –| 199| no function
200| –| 224| reset
225| –| 255| no function
CH10| 000| –| 255| sound sensitivity/auto mode speed
CH11| ****
master color selection
| 000| –| 255| red dimmer
CH12| 000| –| 255| green dimmer
CH13| 000| –| 255| blue dimmer
CH14| 000| –| 255| white dimmer
colour macro:
031 – 045| R
046 – 060| G
061 – 075| B
076 – 090| W
091 – 105| RG
106 – 120| RB
121 – 135| RW
136 – 150| GB
151 – 165| GW
166 – 180| BW
181 – 195| RGB
196 – 210| RGW
211 – 225| RBW
226 – 240| GBW
241 – 255| RGBW
CH15| ****
mechanic control
| 000| –| 255| pan| ****
Head 2
---|---|---|---|---|---|---
CH16| 000| –| 255| pan fine
CH17| 000| –| 255| tilt
CH18| 000| –| 255| tilt fine
CH19| 000| –| 255| head speed, fast to Slow
CH20| dimmer| 000| –| 255| dimmer, 0% – 100%
CH21| strobe| 000| –| 010| no-strobe
011| –| 255| slow to fast
CH22
| | 000| –| 030| use CH11-CH14 to control colour
031| –| 255| colour macro
(see colour macro table)
CH23
| ****
auto mode / sound mode / reset
| 000| –| 007| no function
008| –| 030| show mode 1
031| –| 053| show mode 2
054| –| 076| show mode 3
077| –| 099| show mode 4
100| –| 122| sound control mode
123| –| 199| no function
200| –| 224| reset
225| –| 255| no function
CH24| 000| –| 255| sound sensitivity/auto mode speed
CH25| ****
master color selection
| 000| –| 255| red dimmer
CH26| 000| –| 255| green dimmer
CH27| 000| –| 255| blue dimmer
CH28| 000| –| 255| white dimmer
CH29| ****
mechanic control
| 000| –| 255| pan| ****
Head 3
CH30| 000| –| 255| pan fine
CH31| 000| –| 255| tilt
CH32| 000| –| 255| tilt fine
CH33| 000| –| 255| head speed, fast to slow
CH34| dimmer| 000| –| 255| dimmer, 0% – 100%
CH35| strobe| 000| –| 010| no-strobe
011| –| 255| slow to fast
CH36
| | 000| –| 030| use CH11-CH14 to control color
031| –| 255| color macro (see color macro table)
CH37
| ****
auto mode / sound mode / reset
| 000| –| 007| no function
008| –| 030| show mode 1
031| –| 053| show mode 2
054| –| 076| show mode 3
077| –| 099| show mode 4
100| –| 122| sound control mode
123| –| 199| no function
200| –| 224| reset
225| –| 255| no function
CH38| 000| –| 255| sound sensitivity/auto mode speed
CH39| ****
master color selection
| 000| –| 255| red dimmer
CH40| 000| –| 255| green dimmer
CH41| 000| –| 255| blue dimmer
CH42| 000| –| 255| white dimmer
colour macro:
031 – 045| R
046 – 060| G
061 – 075| B
076 – 090| W
091 – 105| RG
106 – 120| RB
121 – 135| RW
136 – 150| GB
151 – 165| GW
166 – 180| BW
181 – 195| RGB
196 – 210| RGW
211 – 225| RBW
226 – 240| GBW
241 – 255| RGBW
CH43| ****
mechanic control
| 000| –| 255| pan| ****
Head 4
---|---|---|---|---|---|---
CH44| 000| –| 255| pan fine
CH45| 000| –| 255| tilt
CH46| 000| –| 255| tilt fine
CH47| 000| –| 255| head speed, fast to slow
CH48| dimmer| 000| –| 255| dimmer, 0% – 100%
CH49| strobe| 000| –| 010| no-strobe
011| –| 255| slow to fast
CH50
| | 000| –| 030| use CH11-CH14 to control color
031| –| 255| color macro
(see colour macro table)
CH51
| ****
auto mode / sound mode / reset
| 000| –| 007| no function
008| –| 030| show mode 1
031| –| 053| show mode 2
054| –| 076| show mode 3
077| –| 099| show mode 4
100| –| 122| sound control mode
123| –| 199| no function
200| –| 224| reset
225| –| 255| no function
CH52| 000| –| 255| sound sensitivity/auto mode speed
CH53| ****
master color selection
| 000| –| 255| red dimmer
CH54| 000| –| 255| green dimmer
CH55| 000| –| 255| blue dimmer
CH56| 000| –| 255| white dimmer
colour macro:
031 – 045| R
046 – 060| G
061 – 075| B
076 – 090| W
091 – 105| RG
106 – 120| RB
121 – 135| RW
136 – 150| GB
151 – 165| GW
166 – 180| BW
181 – 195| RGB
196 – 210| RGW
211 – 225| RBW
226 – 240| GBW
241 – 255| RGBW
Colours of light
WWW.CAMEOLIGHT.COM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>