cameo CLF1VMOUNTAP Adapter for Mounting Standard V-Mount Batteries On CLF1 Spotlights User Manual
- June 6, 2024
- cameo
Table of Contents
USER MANUAL
CLF1VMOUNTAP
ADAPTER FOR MOUNTING STANDARD V-MOUNT BATTERIES ON CLF1 SPOTLIGHTS
INTRODUCTION
Operate a CL F1 spotlight independently of a mains connection using the optionally available CLF1VMOUNTAP adapter and a standard V-mount battery.
INTENDED USE
The product is a device for event technology!
The product has been specially developed for professional use in the area of
event technology and is not suitable for use in a household setting!
Furthermore, this product is only intended for qualified users with expertise
in event technology!
Use of the product contrary to the specified technical data and operating
conditions is considered improper!
Liability for damages or third-party damage to persons and property due to
improper use is excluded!
SAFETY INFORMATION
- Please read this user manual carefully.
- Keep all information and instructions in a safe place.
- Follow the instructions.
- Only use the V-mount adapter as properly intended.
KEEP AWAY FROM CHILDREN! THE PRODUCT CONTAINS SMALL PARTS AND PACKAGING MATERIAL THAT COULD BE SWALLOWED! PLASTIC BAGS MUST BE KEPT OUT OF THE REACH OF CHILDREN!
INSTALLATION
Fully disconnect the spotlight from the mains (pull out the mains plug).
Loosen and remove the four Allen screws, marked in the figure below, on the
rear of the spotlight using a suitable tool (A). Insert the four spacer
sleeves attached to the V-mount adapter into the corresponding screw holes (B)
and screw the adapter into the rear of the spotlight using the included screws
(C).
Keep the original screws, which have been removed, for later reassembly.
Insert a fully-charged standard 14.4 or 14.8 volt V-mount battery into the
adapter and connect the connection cable to the 4-pin XLR socket of the
spotlight (BATTERY).
The spotlight will now begin the start-up process and is operational after a
short time.
Please note: if you connect the mains power supply to the spotlight during battery operation, the spotlight will restart and it is only operational again after the start-up process (= operation with mains power). The same applies if you disconnect the mains power supply from the spotlight while a battery is connected (= battery operation).
Note: a connected battery is not supplied with charging voltage when the mains power supply is connected at the same time.
Caution: to avoid damage to the spotlight, the plus and minus contacts of the connection cable must not be interchanged!
BATTERY RUNTIME
With the F1T and F1D models and a battery with 100 Wh of electrical energy,
the battery runtime in Full On operation is calculated to be around 65
minutes.
With the F1FC model and a battery with 100 Wh of electrical energy, the
battery runtime in Full On operation is calculated to be around 45 minutes.
For batteries with a larger capacity, the runtime is extended accordingly.
The actual battery runtime depends on the ambient temperature and the
technical characteristics of the battery used (e.g. final discharge voltage).
TECHNICAL SPECIFICATIONS
| Article number: | CLF1VMOUNTAP |
|---|---|
| Product type: | Spotlight accessory |
| Type: | Adapter for mounting standard V-mount batteries on compatible |
spotlights
Compatible spotlights:| CL F1 Series
Components:| Mounting plate, battery adapter, connection cable, screw set
Battery requirements:| V-mount connection
14.4 or 14.8 volt nominal (min. 11 volt max. 17 volt)
F1T / F1D: load capacity up to 10 A
F1FC: load capacity up to 15 A
Pin assignment of connection cable (4-pin XLR plug):| pin 1 = negative (-)
pin 4 = positive (+)
Color:| Black
Material:| Metal / plastic
Dimensions of mounting plate (W x H x D):| 119.5 x 166.5 x 35.5 mm
Total weight:| 0.29 kg
PROPDR DISPOSAL OF THIS PRODUCT
(Valid in the European Union and other European countries with waste separation)
This symbol on the product or the associated documents indicates that the device must not be disposed of with normal household waste at the end of the product’s life, in order to prevent environmental damage or personal injury caused by the uncontrolled disposal of waste. Please dispose of this product separately from other waste and recycle it to promote sustainable economic cycles. Private customers can contact the dealer from whom the product was purchased or the relevant local authorities to obtain information on environmentally friendly waste management. Commercial users can contact their supplier and check the contractually agreed terms and conditions on the disposal of equipment. This product must not be disposed of with other commercial waste.
Subject to printing errors and mistakes, as well as technical or other changes!
MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY
Our currently valid warranty conditions and limitation of liability are
available at:
https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARATIONS_CAMEO.pdf
For servicing, please contact Adam Hall GmbH, Adam-Hall-Str. 1, 61267 Neu
Anspach
E-mail: Info@adamhall.com / +49 (0)6081 / 9419-0
Cameo® is a registered brand of the Adam Hall Group
Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu Anspach | Germany
Phone: +49 6081 9419-0 | adamhall.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>