TELETEK SensoIRIS BSST Intelligent Analogue Addressable Fire Alarm Base Instruction Manual
- June 10, 2024
- Teletek
Table of Contents
TELETEK SensoIRIS BSST Intelligent Analogue Addressable Fire Alarm Base
Introduction
Intelligent analogue addressable fire alarm base with built-in sounder SensoIRIS BSST
DoP No: 079
Address: 14A Srebarna Str,
1407 Sofia, Bulgaria
EN 54-3: 2001/ A2: 2006
Installation
|
Indoor use
Outdoor use
ATTENTION: Read carefully this installation Instructions before installing the device! This manual is subject to change without notice
A-weighted sound level diagram
Installation Instruction
Senso IRIS BSST is аn addressable Fire Base with built-in Sounder and Strobe
in its body. The fire base is designed for installing in addressable fire
alarm systems which support operation via TTE communication protocol. The
device is powered on from the panel and can be controlled via the
communication protocol.
The addressable Senso IRIS BSST fire base supports 32 different tone types at
two sound levels. The tone type and sound level are programmed from the
control panel.
The Senso IRIS BSST is compatible for operation with Senso IRIS addressable detectors series: T110 (IS), S130 (IS) and M140 (IS). The device is designed for easy installation and consists from two parts: mounting plane basis and sounder and strobe combined in a common body with factory mounted fire base.
Installation Instructions
Attention: Power off the loop circuit before installing the SensoIRIS BSST addressable fire base!
-
Choose the proper place for installation of the device.
-
Set the device address using SensoIRIS Programmer or directly from addressable fire panel. The address must be in the range from 1 to 250.
-
Fix the mounting plane basis on the ceiling of the protected premises using fixings according the mounting surface.
-
Run the loop wires and fix the sounder and strobe common body to the mounting basis using the supplied screws in the spare parts kit.
-
Connect the fire base to the fire panel using the wiring diagram.
-
Insert a detector – SensoIRIS T110 (IS)/ S130 (IS)/ M140 (IS) – into the fire base and rotateclockwise until it drops into place – the short mark on the base fits with that on the sounder body. Continue to rotate the detector until its mark coincides with the long mark on the base – a click is heard.
Note: The mounted detector on the SensoIRIS BSST base is assigned at different address to the control panel! -
Program the sounder and strobe parameters. Refer to the Programming manual of the control panel for more details. The programming manuals for IRIS and SIMPO fire alarm panels are accessible for download from the site of the manufacturer: http://www.teletek-electronics.com
-
Test the sounder and strobe for proper operation.
Warranty
All devices carry on a warranty valid from the date of manufacture. The date of manufacture can be checked by the code sticker label on the back of the device. The date is printed with white numbers into a black area . The first two numbers represent the year and the last two – the month. For example: The date code “20 07”, means the detector is manufactured in July, 2020.
To return goods for warranty service, please contact with your local distributer for details.
TECHNICAL SPECIFICATIONS
Operating Voltage Range. . . . . . . . .
Maximal consumption at communication . . . . . . . . .
Maximal consumption: . . . . . .
– main tone type 27, low volume level . . .
– main tone type 27, high volume level . . . .
Power volume (main tone type 27): . . . . . .
– low volume (up to 100 pcs BSST(IS) to the loop) . . . .
– high volume (up to 30 pcs BSST(IS) to the loop) . .
Power volume (other tone types): . . . . . .
– low volume (up to 100 pcs BSST(IS) to the loop) . . .
– high volume (up to 30 pcs BSST(IS) to the loop) . . .
Frequency of the strobe flashing . . . . . .
Number of tone types. . . . .
Supported communication protocol . . .
Wire Gauge for terminals . . . . .
Relative humidity resistance . . . . .
Material (transparent), color . . .
Dimensions . .
Dimensions with mounted detector T110/S130 . .
Dimensions with mounted detector М140 . . . .
Mounting basis
Address programming
- Use the cable with 5-pin terminal.
Note: You may also program the address directly from the fire panel.
Installation
Wiring Diagrams
RI – Remote Indicator
+Loop – Positive loop wire
-Loop – Negative loop wire
Legend/ With detector with built-in isolator mounted on the BSST fire
base
With detector without built-in isolator mounted on the BSST fire base
Tone types and description
| Tone | Tone Type | Tone Description / Application |
|---|---|---|
| 1 |  |
970Hz
2| 
|
800Hz/970Hz @ 2Hz
3| 
|
800Hz – 970Hz @ 1Hz
4| 
|
970Hz 1s OFF/1s ON
5| |
970Hz, 0.5s/ 630Hz, 0.5s
6| 
|
554Hz, 0.1s/ 440Hz, 0.4s (AFNOR NF S 32 001)
7| 
|
500 – 1200Hz, 3.5s/ 0.5s OFF (NEN 2575:2000)
8| |
420Hz 0.625s ON/0.625s OFF (Australia AS1670 Alert tone)
9| |
500 – 1200Hz, 0.5s/ 0.5s OFF x 3/1.5s OFF (AS1670 Evacuation)
10| |
550Hz/440Hz @ 0.5Hz
11| 
|
970Hz, 0.5s ON/0.5s OFF x 3/ 1.5s OFF (ISO 8201)
12| |
2850Hz, 0.5s ON/0.5s OFF x 3/1.5s OFF (ISO 8201)
13| |
1200Hz – 500Hz @ 1Hz (DIN 33 404)
14| 
|
400Hz
15| |
550Hz, 0.7s/1000Hz, 0.33s
16| |
1500Hz – 2700Hz @ 3Hz
17| 
|
750Hz
18| |
2400Hz
19| |
660Hz
20| |
660Hz 1.8s ON/1.8s OFF
21| |
660Hz 0.15s ON/0.15s OFF
22| |
510Hz, 0.25s/ 610Hz, 0.25s
23| |
800/1000Hz 0.5s each (1Hz)
24| |
250Hz – 1200Hz @ 12Hz
25| 
|
500Hz – 1200Hz @ 0.33Hz
26| |
2400Hz – 2900Hz @ 9Hz
27| |
2400Hz – 2900Hz @ 3Hz ( 2500Hz – main sound frequency
28| |
800Hz – 970Hz @ 100Hz
29| |
800Hz – 970Hz @ 9Hz
30| |
800Hz – 970Hz @ 3Hz
31| |
800Hz, 0.25s ON/1s OFF
32| 
|
600Hz – 1100Hz, 2.6s/0.4s OFF
020776; RevD; 01/2022
Documents / Resources
|
TELETEK SensoIRIS BSST Intelligent Analogue Addressable Fire Alarm
Base
[pdf] Instruction Manual
SensoIRIS BSST Intelligent Analogue Addressable Fire Alarm Base, SensoIRIS
BSST, Intelligent Analogue Addressable Fire Alarm Base, Analogue Addressable
Fire Alarm Base, Addressable Fire Alarm Base, Fire Alarm Base, Alarm Base,
Base
---|---