TYGER TG-LX3D82358 LanderX Running Board Instruction Manual
- June 1, 2024
- TYGER
Table of Contents
TYGER TG-LX3D82358 LanderX Running Board
BEFORE INSTALLATION
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT:
TORQUE VALUES
Fastener Size| Class 8.8 Torque (ft-lbs)| Class 10.9 Torque (ft-
lbs)
---|---|---
6mm| 6-7| 6-7
8mm| 15-16| 22-23
10mm| 31-32| 44-45
12mm| 54-55| 78-79
14mm| 87-88| 125-126
Parts List
x1 Driver/Left TYGER LanderX
x1 Passenger/Right TYGER LanderX
x4 Front/Rear Upper Mounting Brackets
x4 Front/Rear Lower Mounting Brackets
x2 Center Mounting Brackets
x2 Center Support Brackets
x8 8mm x 25mm Hex Bolts
x12 8mm x 25mm Combo Bolts
x20 8mm x 24mm OD x 2mm Flat Washers
x16 8mm x 16mm OD x 1.6mm Flat Washers
x28 8mm Nylon Lock Nuts
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. USE WIRE BRUSH TO
CLEAN MOUNTING STUDS OF PAINT AND DEBRIS.
INSTALLATION INSTRUCTION
STEP 1
Start the installation under the Driver/Left side of the vehicle. Locate
the front (3) factory studs along the inner side of the body panel (Fig 1).
STEP 2
Select (1) Front Upper Mounting Bracket. Attach the Mounting Bracket to the
(3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts
(Fig 2). DO NOT tighten hardware.
STEP 3
Select (1) Front Lower Mounting Bracket. Attach the Lower Bracket to the
short side of the Upper Bracket with (2) 8mm Hex Bolts, (4) 8mm x 16mm Flat
Washers and (2) 8mm Nylon Lock Nuts (Fig 3). DO NOT tighten hardware.
STEP 4
Move to the center location (Fig 4). Select (1) Center Support Bracket.
Attach the Support Bracket to the (2) lower threaded studs with (2) 8mm x 24mm
Flat Washers and (2) 8mm Nylon Lock Nuts (Fig 5). Select (1) Center Mounting
Bracket and attach to the Support Bracket and upper threaded stud with (2) 8mm
x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts (Fig 6). DO NOT tighten
hardware.
STEP 5
Repeat STEPS 2-3 to attach (1) Rear Upper Mounting Bracket and (1) Rear Lower
Mounting Bracket to the rear mounting location (Fig 7). DO NOT tighten
hardware.
STEP 6
Select the Driver/Left TYGER LanderX. With assistance, place the TYGER
LanderX onto the (3) Mounting Brackets. Attach the TYGER LanderX to the
Mounting Brackets with (6) 8mm Combo Bolts (Fig 8). DO NOT tighten hardware.
STEP 7
Level and adjust the TYGER LanderX as necessary, then fully tighten all
hardware.
STEP 8
Repeat STEPS 1-7 to attach the Passenger/Right TYGER LanderX.
STEP 9
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>