LUMBER JACK WB1520D4 Solid Wood Bench Instruction Manual
- June 6, 2024
- LUMBER JACK
Table of Contents
Safety & Operating Manual
Solid Wood Bench
WB1520D4
ORIGIMAL INSTRUCTIONS
Welcome to Lumberjack!
Dear Customer, Congratulations on your purchase. Before using the product for
the first time please be sure to read these instructions for use.
They provide you with all information necessary for using the product safely
and to ensure its long service life.
Closely observe all safety information in these instructions!
GENERAL TOOL SAFETY WARNINGS & SPECIFICATION
WARNING Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in serious injury. Save all warnings
and instructions for future reference.
a) Do not exceed weight capacities for the Workbench shelves and drawers. Be
aware of dynamic loading! Sudden load movement may briefly create excess load
causing product failure.
b) Use only on flat, level, and hard surfaces capable of supporting the
Workbench and any item(s) placed on Workbench. Evenly distribute load on Table
to avoid tipping.
c) Use as intended only. Do not use Workbench to perform task for which it was
not designed.
d) For indoor use only.
e) Assemble only according to these instructions. Improper assembly can create
hazards.
f) Wear ANSI-approved safety goggles and heavy-duty work gloves during
assembly and use.
g) Keep assembly area clean and well lit.
h) Keep bystanders out of the area during assembly.
i) Do not assemble when tired or when under the influence of drugs or
medication.
j) This product is not a toy. Do not allow children to play with, on, or near
Workbench.
k) Inspect before every use; do not use if parts are loose or damaged.
Specifications:
Vice Capacity: 7″ Inch
Top Shelf Weight Capacity: 113kg
Drawer Weight Capacity: 11kg
Bottom Shelf Capacity: 90kg
Dimensions (Including Vice): L) 1520mm x W) 620mm x H) 820mm
Drawer Inside Dimensions (x4): L) 365mm x W) 420mm x H) 70mm
Parts List
|
---|---
|
Number | Description | quantity |
---|---|---|
1 | Side Legs | 2 |
2 | Lower Support Brackets (Recessed: | 2 |
3 | Bottom Shelf | 1 |
4 | Upper Support Brackets | 2 |
5 | Table Top | 1 |
6 | Middle Drawer Runners | 1 |
7 | Vice | 1 |
8 | Left Drawer Side | 4 |
9 | Right Drawer Side | 4 |
10 | Drawer Back | 4 |
11 | Drawer Bottom | 4 |
12 | Drawer Front | 4 |
13 | Drawer Handle | 4 |
14 | Wooden Dogs (Image Below) | 4 |
15 | Metal Dogs (Image Below) | 4 |
--- | --- | |
Part No | Description | QTY |
---|---|---|
A | Allen Key | 1 |
B | Dowel Nut | 4 |
C | Long Bolt | 4 |
C1 | Washer | 8 |
D | Bronze Screw | 8 |
E | Heavy Duty Screw | 4 |
F | Silver Screw | 32 |
G | Drawer Handle Screw | 8 |
ASSEMBLY INSTRUCTIONS
Stage 1 Assembly of work bench frame.
Parts required for this section: A) x1, B) x4, C) x4, C1) x4, 1) x2, 2) x2 &
3) x1
Place the washer (C1) over bolt (C) and insert through the side leg (1) to
attach the lower support bracket (2). Place the dowel nut into the pre cut
hole on the support bracket (2) and tighten using the allen key (A)
Repeat this process again for the second side leg (1) for the bench to then look like the below image.
Insert bottom shelf (3) by sliding into the recess of the support bracket (2).
Then attach the second support bracket (2) to the side legs (1) using bolt
(C), washer (C1) & dowel nut (B)
Congratulations stage one is now complete.
Your bench should now look like the image below.
Stage 2 Attaching the drawer runners, upper support brackets & table top.
Parts required for this section: D) x8, E) x4, C1) x4, 4) x2, 5) x1 & 6) x1.
(You will also require a cross headed screwdriver & a 13mm spanner)
Attach upper support bracket (4) to the side leg (1) using screw (D)
Repeat this process for both support brackets (4) as per the image below.
To attach the middle drawer runner (6) use screw (D) ensuring the screw locates into the pilot hole on the middle drawer runner (6) as shown in below image.
Please ensure the middle drawer (6) match the side legs (1). Gap to the rear of the bench and flush to the front of the bench. As seen in image below.
Attach the table top (5), using screws (E) & washers (C1). Insert the screws from underneath the table top (5) to secure the bench frame.
Once you have secured the table top (5) Lastley add screw (D) underneath at the middle of the table top. (see below)
Your bench should then look like the image below.
Finally, attach the vice (7) to the front of the table top (5) into the pre drilled holes on the right.
Congratulations stage two is now complete.
Your bench should now look like the image below.
Stage 3 Assembly of the drawers.
Parts required for this section: 8) x4, 9) x4, 10) x4, 11) x4, 12) x4, 13) x4,
F) x32 & G) x8 (You will also require a cross headed screwdriver)
To assemble the drawer take both sides & back (8), (9) & (10). Place on the
table top (5). Ensure the rails for the drawer are facing outwards and the
recess to the bottom. Using screw (F) secure all three pieces together as
shown in the images below.
Next slide the drawer bottom (11) into the recess of the drawer sides and back (8), (9) & (10).
Attach the drawer handle (13) using screw (G) from the rear of the drawer front (12)
Attach the front of the drawer (12) to the sides of the drawer (8) & (9) using screws (F) Repeat this process for all four drawers.
When inserting the drawers please ensure the runner clip is facing forwards as seen in the image below.
Congratulations stage three is now complete. Your bench is now ready to use.
We wish you many years of enjoyment with your new bench.
|
---|---
Certificate of Registration
This is to certify that
HATY SRL
“the certified site” has been certified in accordance with the requirements of the Forest Stewardship Council® A.C. using the FSC® Chain of Custody standards* and that HATY SRL of
Calea lui Traian, Nr. 201, Babeni, Valcea, 245100, ROMANIA
is hereby licensed to use the FSC Logo on and sell as FSC certified all
products listed on the attached FSC product schedule as FSC 100%
CA-COC-006-17 Nav 2018 © Prepared by Soil Association Certification Lid FSC Licence Code PSC® A000525
“This certificate is only valid.for sale of PSC products when accompanied by a
current product schedule. Validity of this certificate shall alto be verified
by checking the FSC database: INFP.{scory or by contacting Soil Association
Certification: forestry@suilassociation.org This Certificate is the property
of Soil Association Certification Ltd and all copies or reproductions of the
certificate shall be destroyed or returned to the Sail Association
Certification Ltd immediately, on request:
A description of the products, sites, or services that are included in the
scope of the certificate may be obtained from Soil Association – Certification
on request.
‘This certificate itself does not constitute evidence that a particular
product seppiiedby the certificate holder is PSEC certified (or FSC controlled
wood }. Products offered, shipped, or sold by the certificate holder can only
be considered covered by the scope of this certificate when the required FSC
claim is clearly stated on invoices and shipping documents.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>