GERMAN GID-RS32T Free Standing Ceramic Cooktop User Manual

: June 10, 2024
: German

Table of Contents

GERMAN GID-RS32T Free Standing Ceramic Cooktop
Product Information
Product Usage Instructions
Safety Instructions
Product Structure
Operating Instructions
Cleaning & Maintenance
Error Code
Technical Specification
Warranty Terms & Conditions
Customer Service & Repair Centre
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GERMAN GID-RS32T Free Standing Ceramic Cooktop

Product Information

The product is a Free2-s-itna-1ndFirnege SCtearnadminigcSCteoaomktOovpen GGIDPU-R-6SS3S2LT GPNB-6SSL. It is an electric stove with a ceramic glass panel and a control panel.The stove has a silicon rubber ring that should not be touched or covered during use. The stove works with pots and pans made of high temperature resistant materials, with a diameter not exceeding 225mm. The product has safety instructions, technical specifications, warranty terms and conditions, and an error code for troubleshooting.

Product Usage Instructions

Before using the product, please read the safety instructions and warranty information carefully. Remove any plastic bags, poly foam, leaflets, etc., to ensure that the stove is clean, the bottom vent is not blocked, and the power cord or plug is not damaged. If the furnace surface is damaged, contact the Customer Service & Repair Center for replacement.

Use sockets with various technical indicators meeting the standards. Use a pot of suitable size and place it at the center of the furnace surface to avoid touching the silicon rubber ring. Make sure the furnace and bottom of the pot are dry and clean before heating. Do not heat an empty or dry pan. During cooking, do not leave for a long time.

The product must be used in a place that children cannot touch. Place the product on a level bench, avoid using it on a blanket, tablecloth or film to prevent the bottom vent from being blocked. Do not touch or move the product during the working process of the product and during flashing. The furnace surface is still hot during heating and after shutdown. Keep away from combustibles such as paper, rags, curtains or cleaners to avoid fire!

Do not heat paper, film, plastic and other inflammables on the furnace surface to avoid fire. Do not directly heat food on the furnace surface, especially the food with much oil and grease is easy to cause fire when heated! After shutdown, the fan is in normal operation when it is working for heat dissipation. Please do not pull out the plug immediately. Do not touch or clean the furnace surface during the display screen flashing.

When selecting a pot or pan, there are not too many restrictions. All pots and pans made of high temperature resistant materials can be used. It is recommended to use smooth flat-bottomed pots and pans with size not more than 225mm in diameter, and placed in the center of the furnace surface for heating, to avoid touching the silicon rubber ring. Before heating, make sure that the bottom of the pot is dry and clean, and there is no residue to avoid affecting the effectiveness of the product.

Safety Instructions

Before use, please remove the plastic bag, poly foam, leaflet, etc. to ensure that the body is clean, the bottom vent is not blocked, and the power cord or plug is not damaged. If the furnace surface is damaged, please contact our Customer Service & Repair Center for replacement to avoid danger.
When using the product, it is necessary to use sockets with vari-ous technical indicators meeting the standards.
Please use a pot of suitable size. The diameter of the pot shall not exceed 225mm and the pot shall be placed at the center of the furnace surface to avoid touching the silicon rubber ring.
Please make sure the furnace and bottom of pot are dry and clean before heating. Do not heat an empty or dry pan. During cooking, do not leave for a long time.
The product must be used in a place that children cannot touch.
The product shall be placed on the level bench, avoid being used on the blanket, tablecloth or film to prevent the bottom vent from being blocked.
The product will heat up quickly after opening. Please do not touch or move the product during the working process of the product and during “ ” flashing. The furnace surface is still hot during heating and after shutdown. Please keep away from combustibles such as paper, rags, curtains or cleaners to avoid fire!
Do not heat paper, film, plastic and other inflammables on the furnace surface to avoid fire!
Do not directly heat food on the furnace surface, especially the food with much oil and grease is easy to cause fire when heated!
After shutdown, the fan is in normal operation when it is working for heat dissipation. Please do not pull out the plug immediately. Please do not touch or clean the furnace surface during the dis-play screen flashing “ ” .

Product Structure

Body

Ceramic Glass Panel
Control Panel
Power Cord
Silicon rubber ring

Control Panel

Turn Knob
TIMER
ON/OFF + LED Display
HEAT ZONE

Operating Instructions

Utensil Selection

There are not too many restrictions on the selection of pots and pans. All pots and pans made of high temperature resistant materials can be used.
It is recommended to use smooth flat-bottomed pots and pans with size not more than 225mm in diameter, and placed in the center of the furnace surface for heating, to avoid touching the silicon rubber ring.
Before heating, please make sure that the bottom of the pot is dry and clean, and there is no residue to avoid affecting the effectiveness of the product.

Quick Start Guide

BUTTON	FUNCTION

TIMER

|

Set COUNTDOWN TIMER

|

HEAT ZONE

| Select DOUBLE RING, INNER RING ONLY or OUTER RING ONLY Mode
| ON/OFF + LED

Display

| Control ON/OFF and display selected mode
|

Turn Knob

|

Adjust power level

STANDBY MODE
After plugging in the power source, buzzer will beep once, LED Display will show “- -“, and the product will enter into STANDBY MODE.

to enter into COOKING MODE

In STANDBY MODE, press LED Display ****and then press , product will enter into DEFAULT COOKING MODE of DOUBLE RING, and LED Display will show “20” (2,200W).

Select HEAT ZONE

When product is in COOKING MODE, press to select among DOUBLE RING, INNER RING ONLY and OUTER RING ONLY modes.

HEAT ZONE

|

DEFAULT POWER LEVEL

| INDICATOR LIGHT DISPLAY
---|---|---

DOUBLE RING

| Display Shows “20” 2,200W Power Output|

Light On

INNER RING ONLY

| Display Shows “41” 1,100W Power Output|

Light Off

OUTER RING ONLY

| Display Shows “71” 1,100W Power Output|

Light On

Adjust POWER LEVEL

When product is in COOKING MODE, rotate TURN KNOB ****to adjust desired POWER OUTPUT:

In DOUBLE RING mode, turn knob to adjust 01-20 (300W-2,200W);
In INNER RING ONLY mode, turn knob to adjust 30-41 (100W-1,100W);
In OUTER RING ONLY mode, turn knob to adjust 60-71 (100W-1,100W).

Set TIMER COUNTDOWN

When product is in COOKING MODE, press to set TIMER COUNTDOWN. Rotate TURN KNOB clockwise one click to add 1 minute to Timer (maximum 99 min., minimum 1 min.) 3 seconds after Timer is set, product will automatically start countdown, Timer and Powel Level will display in alternation. To cancel Timer, ****press for 3 seconds.

WARNING:

When product is in use, DO NOT allow children near product to avoid danger!
When product is in use, DO NOT touch or move product to avoid getting burnt!
DO NOT unplug the product immediately after use, because the built-in fan system is still dissipating residual heat!
Even after product is turned off, the product is still hot to the touch. DO NOT touch the product for at least 1 hour, to allow product to cool down completely. DO NOT touch, move or clean the product until it has completely cooled down!
UNDER NO CIRCUMSTANCES should food be cooked directly on the cooktop surface. This product should be used with appropriate cookware at all times!
DO NOT place any flammable items on top or around the vicinity of the product, such as paper, film, plastic, cloth, curtain etc. to avoid fire hazard!

Cleaning & Maintenance

Before cleaning and maintenance, make sure product has been unplugged and the furnace surface has cooled to normal temperature!
Do not wash product directly with water or immerse product in water.
If there is cooking residue on the furnace surface, gently scrape off with a ceramic hob scraper at a 45 degree angle, and then wipe clean with a soft wet cloth. It can also be wiped with neutral detergent. Do not use corrosive liquid or steel scrubber for cleaning to avoid damaging the surface of the ceramic glass panel.

Error Code

ERROR CODE|

ANALYSIS

|

SOLUTION

---|---|---

E1

|

Voltage lower than 90V

| Check power supply first; if problem remains, contact Customer Service and Repair Centre

E2

|

Voltage higher than 280V

| Check power supply first; if problem remains, contact Customer Service and Repair Centre

E3

| Sensor detects temperature higher than

750°F

| Contact Customer Service and Repair Centre

E4

| 1. Temperature sensor is short circuited or open circuited during operation

2. Heating plate is burnt out and product cannot heat up

3. Fuse is cut

4. PCB power board malfunction

|

Contact Customer Service and Repair Centre

E5

|

PCB power board overheated

| Restart the product; if problem remains, contact Customer Service and Repair Centre

E6

|

Sensor detects short circuit or open circuit

| Contact Customer Service and Repair Centre

E7

|

Fan malfunction

| Contact Customer Service and Repair Centre

ATTENTION:
If problem remains unsolved, please contact Customer Service and Repair Centre. Disassembly and repair of this product must only be conducted by qualified professionals.

Technical Specification

Model	GID-RS32T
Rated Voltage/Frequency	220V / 50Hz – 60Hz
Rated Power	2,200W
No. of hob	1
Product Dimensions	(H)80 (Φ)280 mm
Net Weight	Approx. 1.9kg
Gross Weight	Approx. 2.2kg
Power Range	100W – 2,200W

All information in this manual is for reference only. If there are any errors or omissions, the specifications produced by the factory shall prevail. Specification is subjected to change without prior notice.
If there is any inconsistency or ambiguity between the English version and the Chinese version of this manual, the Chinese version shall prevail.
Refer to www.germanpool.com for the most up-to-date version of the Operating Instructions.

Warranty Terms & Conditions

Under normal operations, the product will gurantee a 1-year full warranty provided by German Pool (effective from the date of purchase).

This warranty is not valid until customer registration information is received by our Service Centre within 10 days of purchase via one of the following means:
1. Visit our website and register online: www.germanpool.com/warranty
2. Complete all the fields on the attached Warranty Card and mail it back to our Customer Service Centre.

Please fill out the form below. This information and the original purchase invoice will be required for any repairs. Warranty will be invalidated if information provided is found to be inaccurate.

Model No. : GID-RS32T
Serial No. :
Purchased From :
Invoice No. :
Purchase Date :

Customer who fails to present original purchase invoice will not be eligible for free warranty service.
Customer should always follow the operating instructions. This warranty does not apply to:
- labour costs for on-site installation, check-up, repair, replacement of parts and other transportation costs;
- damages caused by accidents of any kind (including material transfer and others);
- operating failures resulting from applying incorrect voltage, improper usage, and unauthorized installations or repairs.
This warranty is invalid if:
- the purchase invoice is modified by an unauthorized party;
- the product is used for any commercial or industrial purposes;
- the product is repaired or modified by unauthorized personnel, or unauthorized parts are installed;
- the serial number is modified, damaged or removed from the product.
German Pool will, at its discretion, repair or replace any defective part.
This warranty will be void if there is any transfer of ownership from the original purchaser.