RBROHANT JK0128-9 Bluetooth Deluxe Digital Thermostatic Shower System Instruction Manual
- June 17, 2024
- RBROHANT
Table of Contents
User’s Manual
JK0128-9 Bluetooth Deluxe Digital Thermostatic Shower System
INSTALLATION INSTRUCTIONS
Installation Manual
JK0128
BEFORE INSTALLATION
Precautions and Maintenance
-
In order to ensure the durability of the product, please be as gentle and slow as possible during operation.
-
Clean the filter regularly.
-
When the shower is used for a long time and water is found to flow out intermittently there must be debris blocking the water outlet. At this time, you only need to gently touch & clean the soft rubber tips on the shower, then the debris will be automatically
rushed out. -
If any dirt on surface, clean with soft liquid or transparent glass detergent, then rinse it with soft water, finally gently wipe it with a dry soft cloth.
-
Do not use any scrubbing detergent, polisher, sand-cloth, paper tissue, or scraper.
-
Do not use acid detergent, insoluble & grain-like detergent or soap.
-
If you will not use the shower for a long time, please close the main water inlet valve in your home.
-
When the ambient temperature is under 0° C/32° F, please take necessary measures to keep the water equipment warm.
Piping diagram and dimensional drawings
Note:These size are only for reference, please adjust the installation
height according to your needs.
The specific parameters is based on real item you get.
INSTALLATION STEPS
This product has been inspected and debugged by the factory to the best
condition. Please do not disassemble and assemble it yourself.
Before installing the product, please be sure to remove sundries and sludge
from the water pipe to prevent sundries from blocking the product.
1. lnsatallation Steps of Valve Body
-
Turn off the water supply. Determine pipe length and depth. Set up the waterlines properly based on the actual condition. The above digram for plumber reference (Must pay attention-left is hot, right is cold.)
-
Drill 4 positioning holes for the valve body.
The above digram for your reference.
-
Hammer the 4 expansion screws into the holes.
-
Fix the vale body with 4 positioning screws.
-
Use copper sleeve wrench to tighten the screws.
-
Connect the hot/cold inlets and outlets properly. Open the water supply to check and test, ensure there is no leakage or blockage at each connection.
-
Fill the installation slot with concrete and paste the tile, which is flush with the hidden box.
-
Use a phillips screwdriver to loosen the four M5 screws of the protection box at counterclockwise direction and then take out the protection box. And then turn the handles all upwards like the picture .
-
Tighten the 4 lengthening rods on the key spool, then set the positioning plate on the flat wall, and cut off the excess part of the outer plane of the lengthening rod extension positioning plate with the cutting machine or blade. Then remove the positioning plate and press the figure.
-
Rotate the spool rod to adjust the marking line on the spool so that the upper and lower marking lines are aligned. As is shown in.
-
Install the panel, rotate the switch handle, align the handle with the OFF on the panel, then install the panel on the main body.
-
Screw the handwheel into the handles. Install the shower holde. Connect the hand shower with the shower holder with the shower hose.
Installation Steps of Rain shower
-
Please screw the M5X20 screws out using the allen wrench.
-
Separate the shower assembly from the bracket.
-
Cut holes at a suitable position under the ceiling refer to the basic size of the product.
-
Refer to the basic size of the product, drill 4-010mm holes at a suitable position under the ceiling.
-
Play the explosion screw heads into the 4 hole with a hammer.
-
Use a socket wrench to remove the lock nut, spring washer, and flat washer counterclockwise
-
Move the bracket upwards so that the four expansion screw heads pass through the four holes of the bracket respectively.
-
Install the washer and spring washer with expansion screw heads, and then use the copper sleeve wrench locks the nut to the bracket, and the bracket is flush with the ceiling.
-
Remove the gypsum board of the ceiling if have, and then connect the 1/2 water inlet hoses (male side) through the hole on the side wall of the bracket to the water inlet hole on the ceiling.
-
Put elbow water hoses through the bracket crossbar and then connect it with the two-way joint. Insert connector 1 and connector 2 into controller and connector 3, respectively.
-
Connect connector 3 and connector 4 together and plug the power plug into the plug-in board.
-
Use a allen wrench to lock the shower panel on the bracket. Then test the rain and waterfall functions working normally or not. At last install the gypsum board.
lnsatallation Steps of Body Jets.
-
Attach the cover plate to body jets.
-
Apply Teflon tape to threaded tail of the body jets.
-
Use a wrench to screw the jet heads clockwise into the body spray outlets.
CLEANING CARE
In order to keep the appearance of product clean, bright and good performance, please take care of the product as follows;
- Rinse with water only and dry with soff cotton cloth;
- Use mild liquid and colorless glass cleaner to remove surface dirt and scale film, or use polish without abrasive effect;
- Do not use abrasive deterfgent, polish, emery cloth, paper towel or scraper, etc;
- Do not use acid cleaner, or cleaner and soap with insoluble gran etc;
- ln the process of use, mud my accumulate in the bubbler and make the water flow show,
The bubbler can be unscrewed, rinsed with water, and then installed back in
place.
Please feel free to contact us if you have any questions. We will help to
solve the issue together with you. OUR EMAIL:
services@rbrohant.com
Service Contact:
+1(801) 800-9309
services@rbrohant.com
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>