FULHAM FHSCP-UNV-10P-S-SD Programmable Emergency LED Driver Instruction Manual

UNV-10P-S-SD Programmable Emergency LED Driver
Instruction Manual

Programmable Emergency LED Driver

• Emergency LED Driver
• Universal Voltage: 120-277V~
• Output Voltage Range: 15-55V
• Output Current: 55-666mA
• Output Wattage: 3W-10W (Factory default 10W)
• Output Type: LED Class 2, Class 2
• Number of Output Channels: 1 Channel

General Specifications

Ring Wave
Protections| Output Open Protection
Output Overload Protection
Output Short Circuit Protection
Output Temperature Protection
Emergency Mode| 90 Minutes  Min
RFI/EMI| FCC Part15A  EN55015
Ambient Operating Temperature Rang| 10°C To 55°C (50°F To 131F°) (>7W)
Sound Rating| 0°C To 55°C (32°F To 131F°) (≤7W)  A
Battery Type| Lithium
Battery Voltage| 11.1V
Pack Capacity| 2400mAh
Battery Rating| 25.92Wh
Battery Count| 3 Cells
Battery Recharge Time| 12 Hours
Battery Discharge Time| Min 1.5 Hours
Test Switch Remote Mounting Distance| 20′ (6m) Max.
Service Life| 50,000 hours
Warranty| 5 years
Safety Standard| UL924, CSA C22.2 No.141-10/cUL
EN61347-1, EN61347-2-7, EN62384, EN60598-2-22, EN50172
CEC, MSDS, DGM EEE C62.41.2-2002
EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3, EN61000-4-4
EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61000-4-29

Mechanical Data

Overall Dimension

Accessories

Wet Location Test Switch: FHS-TSTWL-BC (Optional)

Wall Plate: FHSWLPWH

Wall plate and screw color: white with black lettering| 1.“Charge push to Test”plate
2. (2) 6-32 x ½”LG mounting screws

Wiring Diagram

TOP VIEW

SELF-DIAGNOSTIC INSTRUCTIONS! OPERATION :
If the self-diagnostic feature is enabled: The emergency LED driver will conduct a self-check for thirty(30)seconds every thirty(30)days; and a ninety(90) minutes self-check every 12 months. After every self-check the LED indicator light will indicate a status signal. Check indicator status chart above to diagnose the status signal.
If the self-diagnostic feature Is disabled: User must conduct a manual test every thirty (30) days to ensure the emergency LED light source illuminates as intended. A full discharge test shall be conducted once a year: the LED light source shall illuminate for a minimum of ninety (90) minutes.
*Self Diagnostic feature is factory enabled

TEST SWITCH INDICATOR STATUS:

switch or connection
Flashing Red. 1s on/1s off| Battery Failure, replace battery
Flashing Green. 1s on/1s off| Self-Diagnostic test underway
Fast Flashing Red. 0.1s on / 0.1s off| Abnormal driver performance, replace driver
Slow Fleshing Green 0.15 on/3s off| Normal working in EM mode
Solid Red| No load or output over voltage protection triggered. Check LED connection
**** Slow Flashing Red, 0.5s on / 0.5s off| Charge circuit failure replace driver

TEST SWITCH OPERATIONS
EM Test: Press and hold the test button (>1s) to enter EM mode in normal AC powered.
Manual Self-Diagnostic: After charging twelve (12) hours or battery fully charged, quickly press the test button three(3) times within two (2) seconds to force the controller to enter Self-Diagnostic cycle. To quit the Self- Diagnostic cycle after engaged, press and hold the test button for ten (10) seconds.
Enable/Disable Self-Diagnostic Status: Fast click 2 times within 2s to query the Self-Diagnostic Enabled/Disabled status. The indicator would blink for current status for 3 cycles. 2.5s ON/0.5s OFF stands for Enabled. 0.5s ON/2.5sOFF stands for Disabled.
Load Test: When the test button is flashing red 4s orU4s off. press and hold the test switch for 10s, the unit will enter Self -Diagnostic mode.

Programming:
Unless otherwise programmed the output will self-program to the maximum rating of the battery. This EM driver can be programmed using the Fulham Smart Set TPSB100(E). Programming features include the following:
Output EM power – 3w to 10w
Enable/Disable Self- Diagnostic

• For more detailed programming instructions please see our Programming Instructions and Design Guide found on our website:
  https://www.fulham.com/PDFs/SpecSheets/Fulham-Design-Guide-Programmable- Drivers.pdf
  Guidelines
  

  • Driver must be grounded by means of the Driver case.

Over temperature protection

• The Fulham Hotspot Plus LED drivers are protected against thermal overload. If the temperature limit is exceeded, the output current is reduced.

LED load

• Fulham Hotspot Plus LED drivers are designed to drive passive LEDs, -COB’s and -LED assemblies Proper function is not guaranteed when (LED) loads with active components are used.

Mounting / Cooling

• Above an output power of 20W, the driver needs to be mounted on a heat conductive surface of at least 200cm². Always test if the surface is sucient enough before installing the driver.

Short-circuit protection

• In case of a short circuit the LED driver switches to protection mode. After the removal of the short-circuit the LED driver will recover automatically.

No-load Operation

• In no-load operation the output voltage will not exceed the specified open circuit output voltage.

Hot Swapping

• This driver does not support hot swapping of the LEDs
• Remote Mounting
• Up to 15ft with 18AWG. Contact Fulham for higher remote distance.

Battery Maintenance

• In order to maintain proper operation and warranty coverage, the battery must be recharged once per year prior to installation.

Warranty

• Reference Fulham’s limited Warranty: https://cdn.fulham.com/PDFs/Limited-Warranty.pdf

Part Number Matrix

Packaging

OUTER DIMENSION

Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250
Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.
Specifications subject to change without notice.
order@fulham.com
www.fulham.com
2020-858 Rev B

References

• Fulham: Lighting Solutions | LED Drivers | Ballasts | Emergency | Modules

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>