FULHAM VPR-22-MU-25-9TW-A LED Luminaire Retrofit Kit Instruction Manual

June 9, 2024
FULHAM

FULHAM VPR-22-MU-25-9TW-A LED Luminaire Retrofit Kit

FULHAM-VPR-22-MU-25-9TW-A-LED-Luminaire-Retrofit-Kit-
PRODUCT

Installation Warnings

  • To reduce the risk of death, personal injury, property damage from fire, electric shock, falling parts, cuts/abrasions,
    and other hazards make sure to read all warnings and instructions included with and on the fixture box and all fixture labels.

  • Follow these general precautions before installing, servicing, or performing routine maintenance upon this equipment.

  • Commercial installation, service, and maintenance of luminaires should be performed by a qualified licensed
    electrician.

  • LED Retrofit kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.

  • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

  • Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

Warnings

  • Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
  • Turn off the power prior to performing any maintenance
  • Verify that the supply voltage is correct by comparing it with the luminaire label information.
  • All wiring connections should be capped with UL approved wire connectors.

Risk of fire or electric shock. The electrical rating of these products are 120-277 VAC, the installer must determine whether they have 120-277 V at the luminaire before installation.

Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and /or drawings.
Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.

Caution

  • Avoid direct eye exposure to the light source while it is on.
  • Account for small parts and properly dispose of packing material, as these may be hazardous to children.
  • Risk of burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture. NOTE: The green ground screw is installed in its proper location.
  • Do not Relocate.

NOTE: Please use minimum 90°C rated supply conductors.
NOTE: Specifications and dimensions subject to change without notice.
NOTE: Suitable for Dry and Damp location, Type IC.

Retrofit Kit Components

FULHAM-VPR-22-MU-25-9TW-A-LED-Luminaire-Retrofit-Kit-
FIG-1

  • A: End Brackets…………………………..2pcs
  • B: Side Brackets………………………….2pcs
  • C: Retrofit KitHousing…………………..1pcs
  • D: #8 x 1/2” Self-Taping Screws…….4pcs
  • E: Wire Caps………………………………3pcs
  • F: Retrofit Label…………………………..1pcs\

NOTE: The existing fluorescent luminaries housing shall be larger than dimensions described in below table:

General Wiring Diagram

FULHAM-VPR-22-MU-25-9TW-A-LED-Luminaire-Retrofit-
Kit-FIG-2

Field-Adjustable Wattage & CCTFULHAM-VPR-22-MU-25-9TW-A-LED-Luminaire-
Retrofit-Kit-FIG-3

Part Number Power Level CCT Level
VPR22-MU-25-9TW-A 18W / 22W / 25W 3500K – 5000K
VPR24-MU-36-9TW-A 23W / 30W / 36W 3500K – 5000K

Installation

FULHAM-VPR-22-MU-25-9TW-A-LED-Luminaire-Retrofit-Kit-
FIG-4

  • Prior to installation, disconnect all incoming power to the fixture. Remove existing hardware (lens/lens frame, parabolic louver, reflector/ballast covers, brackets, lamps/lamp holders). Leave supply and grounding leads. (Fig. 1)
    NOTE: Follow all federal and local regulations when disposing of lamps and removed components.

  • Install the end brackets to each end of the existing fixture by gently lifting the fixture and placing the end brackets between the fixture and T-grid. (Fig. 2)

  • If you are not pleased with the side gap between the fixture and T-grid, you may install the side brackets between the fixture and T-grid. There are two tabs to allow for placing the side brackets into the slots on the end brackets. (Fig. 3)

  • Secure the end brackets to the existing fixture using the provided #8 x 1/2” self-drilling screws. (Fig. 2A)

  • Place the retrofit kit housing into the slotted keyholes of the end brackets, and the slide it horizontally to the end of the slots. (Fig. 4 & 4A)

  • Hook the safety cables onto the holes positioned on the end brackets. (Fig. 5)

  • Use the provided wire caps to connect the wire leads of the retrofit kit housing to the main power leads.
    (Black-Live, White-Neutral, Green-Grounding) (Fig. 5B)

  • Place the provided Retrofit Label on the original luminaire housing in a readily visible location for anyone attempting to service the luminaire. (Fig. 5-A)

  • Secure the retrofit kit housing by locking the latches onto the end brackets. (Fig. 6)

Additional Accessories (Sold Separately)

Emergency Battery Back-up: FHSCP-UNV-4W-L

  • 4W Constant Power Emergency Back-up
  • 500lm
  • 90 min.Runtime.

Wiring Diagram 1: 3500K Emergency OutputFULHAM-VPR-22-MU-25-9TW-A-LED-
Luminaire-Retrofit-Kit-FIG-6
Wiring Diagram 2: 5000K Emergency OutputFULHAM-VPR-22-MU-25-9TW-A-LED-
Luminaire-Retrofit-Kit-FIG-7

Fulham Co. Inc.: 1 2705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 order@fulham.com
www.fulham.com Installation Instructions subject to change without notice. Page 6 of 6 11/17/2022 INS-VPR, Rev A

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

FULHAM User Manuals

Related Manuals