thomann free solo Active Antenna Splitter User Manual
- June 4, 2024
- Thomann
Table of Contents
thomann free solo Active Antenna Splitter
General notes
This user manual contains important information on safe operation of the device. Read and follow all safety notes and all instructions. Save this manual for future reference. Make sure that it is available to all persons using this device. If you sell the device, include the manual for the next owner. Our products are subject to a process of continuous development. We therefore reserve the right to make changes without notice.
Symbols and signal words
This section provides an overview of the symbols and signal words used in this user manual.
Safety instructions
Intended use
This device is used in wireless transmission systems to distribute and amplify the incoming antenna signals. Use the device only as described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use. This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety
Safety
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard! Ensure that
children do not detach any small parts (e.g. knobs or the like) from the unit.
They could swallow the pieces and choke! Never let children unattended use
electrical devices.
Operating conditions
This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy
dirt, and strong vibrations. Only operate the device within the ambient
conditions specified in the chapter ‘Technical specifications’ of this user
manual. Avoid heavy temperature fluctuations and do not switch the device on
immediately after it was exposed to temperature fluctuations (for example
after transport at low outside temperatures). Dust and dirt inside can damage
the unit. When operated in harmful ambient conditions (dust, smoke, nicotine,
fog, etc.), the unit should be maintained by qualified service personnel at
regular intervals to prevent overheating and other malfunction.
External power supply
The device is powered by an external power supply. Before connecting the
external power supply, ensure that the input voltage (AC outlet) matches the
voltage rating of the device and that the AC outlet is protected by a residual
current circuit breaker. Failure to do so could result in damage to the device
and possibly the user. Unplug the external power supply before electrical
storms occur and when the device is unused for long periods of time to reduce
the risk of electric shock or fire.
Features and scope of delivery
- This appliance is used when multiple radio links are to be operated with a single antenna pair.
- The following features characterize the device:
- Amplifying the high frequency signal of a pair of antennas and distribution to 4 × 2 antenna outputs in the frequency ranges of 470 MHz to 608
- MHz, 614 MHz to 694 MHz and
- 823 MHz to 832 MHz.
- Central 12 V power supply for up to four units
- 19″ rack mountable
- Included accessories: 12 V power adapter, 2 UHF omni-directional antennas, 10 BNC cables.
Installation and starting up
Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively. Create all connections while the device is off. Use the shortest possible high-quality cables for all connections. Take care when running the cables to prevent tripping hazards.
Rack mounting
The unit has been designed for rack mounting in a standard 19-inch rack; it occupies one rack unit.
Notes on radio transmission
Before you start, make sure that the frequencies of the connected wireless systems are legitimate in the respective country and check whether the operation must be registered with the responsible authority. For further information on that refer to the manual of the wireless sys‐ terms.
Attaching and connecting antennas.
Attach the supplied antennas to appropriate positions, such as the PA rack. To improve the transmission quality and to adapt to the spatial conditions, the antennas are rotatable and swiveling. Position the antennas so that all used transmitters (e.g., wireless microphones, body-pack transmitters) are within radio range. Install a BNC cable from both antennas to one of the antenna inputs each of the device.
Setting up the radio connection
Connect one antenna output pair of the device each to the two antenna inputs of a wireless system. To do so, use the supplied BNC cables.
Connecting the power supply
External power supply
The device is powered by an external power supply. Before connecting the
external power supply, ensure that the input voltage (AC outlet) matches the
voltage rating of the device and that the AC outlet is protected by a residual
cur‐rent circuit breaker. Failure to do so could result in damage to the
device and pos‐ sibly the user. Unplug the external power supply before
electrical storms occur and when the device is unused for long periods of time
to reduce the risk of electric shock or fire. Connect the 12 V outputs of the
device to the 12 V power supply inputs of the wireless sys‐ items. To do so,
use the supplied power cords. Connect the power adapter to the unit and then
plug the power adapter into the power outlet.
Taking system in operation
Now switch on the device and the connected wireless systems.
Example
The following illustration shows how to connect the device to the optionally available paddles and to four wireless systems. Instead of the paddles, you can also connect the device to the antennas included in the delivery.
Connections and controls
Front panel
Rear panel
Technical specifications
Protecting the environment
Disposal of the packaging material
For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Disposal of your old device
This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose with your normal household waste. Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>