FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current Instruction Manual

June 9, 2024
FULHAM

FULHAM logo VR44 Vizion LED Retrofit 0-10V Dimming Constant Current
Instruction ManualFULHAM logo LED HIGH-BAY KIT
RETROFIT KIT INSTALLATION MANUAL
FOR FLUORESCENT HIGH-BAY LUMINAIRES

VR44 Vizion LED Retrofit 0-10V Dimming Constant Current

INSTALLATION INSTRUCTIONS
1X4 High-Bay Refrofit Kit
VR44-MU-495-xyy-2400A
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250
Telephone: 1-323-779-2980
Fax: 1-323-754-9060
order@fulham.com
www.fulham.com
Installation Instructions subject to change without notice.
INS-VR44-1X4HIGHBAY, Rev B

INSTALLATION WARNINGS

  1. “THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND HAZARDS INVOLVED.”
  2. “WARNING – Risk of fire or electric shock. LED Retrofit kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.”
  3. “WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that has the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.”
  4. “WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.”
  5. “WARNING –Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.”
  6. “CAUTION – RISK OF FIRE. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.”
  7. “THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY THE AUTHORITIES HAVING JURISDICTION.”
  8. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

ORIGINAL LUMINAIRE DIMENSIONS

Original Luminaire
Mfr: Lithonia Lighting – Model: IBZT5 4LFULHAM logo Minimum Luminaire
Dimensions
Dimensions are inches (millimeters)
FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Featured
Image

  • Remove all the original luminaire parts, hardware, lamp, and ballast in order to begin the retrofit.
  • Original luminaire diffuser and original ground wire will need to be kept for this retrofit.
  • This Kit can be retrofitted into any luminaire with a similar length/height width greater than or equal to the Minimum Luminaire Dimensions described above.

RETROFIT KIT COMPONENTS

Retrofit kit components will be provided as listed below:FULHAM VR44 Vizion
LED Retrofit 0-10V Dimming Constant Current - Fig 2

RECOMMENDED TOOLS (Not Included)

RETROFIT KIT DESCRIPTION

FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Fig
4

ITEM DESCRIPTION QTY
A. LED Modules *4
B. LED Driver *1
C. LED Harness: TLC-HN04 1
D.  6-20 X 3/8”  Pan Head Self Drilling Screws *26
E. Retrofit Warning Label 1
F LED Module Lens: TLE-OPT-120-013 (Optional) *4
G. LED Module Lens End Caps: TLE-OPT-120-020 (Optional) *8
H. Name Plate Label 1

*Note: Item quantity will vary based on retrofit kit model purchased. Please refer to retrofit kit spec sheet for more details.

ORIGINAL LUMINAIRE DISASSEMBLY

  1. Start by removing the Lens from the luminaire. See Picture #1.
    FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Fig
5

  2. Remove the lamps and the ballast/driver channel cover from the luminaire. See Picture #2.

  3. Remove the original ballast from the luminaire. See Picture #3.

  4. FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Fig 6The original ground wire and ballast/driver channel cover will need to be kept for this retrofit.

  5. Luminaire should look like Picture #3 in order to begin the retrofit.
    FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Fig
7

RETROFIT KIT ASSEMBLY

  1. Start by Placing the LED Modules (A) onto the luminaire as shown on Figure 1.
    Note: If kit includes LED Module lens install the LED Module Lens before placing the LED Module onto the Luminaire.
    FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Fig
8

  2. Secure the LED Modules to the luminaire using the provided 6-20 x3/8”Pan Head Self Drilling Screws (D). See Figure 1.

  3. Affix the Retrofit Warning Label (E) in the area where it can be visible during the LED Driver (B) installation. See Figure 2A.
    FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Fig
9

  4. Place the LED Driver (B) on the location shown on figure 2-A.
    Note: If kit includes two LED drivers see Figure 2-B.

  5. Secure the LED Driver (B) to the luminaire using the original screw. If the original screw is not available, use the provided 620 x 3/8” Pan Head Self Drilling Screws (D). See Figure 2-A or Figure 2-B.
    FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Fig
10

  6. Wire the LED driver output wires to LED module input connectors using the provided LED Harness (C). See Figure 3.
    FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Fig
11

  7. Wire the LED driver input wires to the power source. See Figure 3 and refer to the “Connecting Power To The Retrofit Kit” section of Page 7 for appropriate wiring instructions.

  8. Place the provided Name Plate Label (H) on the luminaire in a readily visible location to anyone attempting to service the luminaire. See Figure 4.
    FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Fig
12

  9. Replace the ballast/driver channel cover and luminaire lens. See Figure 5-A.
    Note: if kit included Module Lens then the completed retrofit should look like Figure 5-B.
    FULHAM VR44 Vizion LED Retrofit 0-10V Dimming Constant Current - Fig
13

  10. Completed retrofit should look like Figure 5-Aor Figure 5-B.

Connecting Power to the Retrofit Kit:

  1. Connect the green wire (Ground) from the luminaire to the Ground that is being fed by the power source. Connect these two wires by using a wire connector with a minimum 18AWG rating.
  2. Connect the white wire (Neutral) from the LED Driver to the Neutral being fed by the power source. Connect these two wires by using a wire connector with a minimum 18AWG rating.
  3. Connect the Black wire (Line) from LED Driver to the Line being fed by the power source. Connect these two wires by using a wire connector with a minimum 18AWG rating.

WARRANTY

Please refer to LinearHO kit spec sheet for warranty information
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250
Telephone: 1-323-779-2980
Fax: 1-323-754-9060
order@fulham.com
www.fulham.com
Installation Instructions subject to change without notice.
INS-VR44-1X4HIGHBAY, Rev B

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

FULHAM User Manuals

Related Manuals