Cameo CLMBZ100 Moving Head with Zoom and Unlimited Pan and Tilt Rotation User Manual

CLMBZ100 Moving Head with Zoom and Unlimited Pan and Tilt Rotation
User Manual

YOU‘VE MADE THE RIGHT CHOICE!
We have designed this product to operate reliably over many years. Please read this User‘s Manual carefully, so that you can begin making optimum use of your Cameo Light product quickly. Learn more about Cameo Light on our website WWW.CAMEOLIGHT.COM.

PREVENTIVE MEASURES

1. Please read these instructions carefully.

2. Keep all information and instructions in a safe place.

3. Follow the instructions.

4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.

5. Use the equipment only in the intended manner and for the intended purpose.

6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain that wall mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.

7. During installation, observe the applicable safety regulations for your country.

8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain that the equipment is always installed so that is cooled sufficiently and cannot overheat.

9. Never place sources of ignition, e.g., burning candles, on the equipment.

10. Ventilation slits must not be blocked.

11. This appliance is designed exclusively for indoor use, do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment – in this case, observe the special instructions noted below). Do not expose this equipment to flammable materials, fluids or gases.

12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with liquids, such as vases or drinking vessels, on the equipment.

13. Make certain that objects cannot fall into the device.

14. Use this equipment only with the accessories recommended and intended by the manufacturer.

15. Do not open or modify this equipment.

16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.

17. During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries.

18. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or if it has been damaged in another way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualified personnel.

19. Clean the equipment using a dry cloth.

20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.

21. Plastic bags must be kept out of reach of children.
    FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS:
    

22. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.

23. If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature.

24. Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.

25. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the mains outlet and/or power adapter and the equipment connector.

26. When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.

27. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this can shorten the useful life of the equipment.

28. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an authorised service centre.

29.  To disconnect the equipment from the power mains completely, unplug the power cord or power adapter from the power outlet.

30. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be unlocked before it can be removed. However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be careful when laying cables.

31. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.

32. The device must only be installed in a voltage-free condition (disconnect the mains plug from the mains).

33. Dust and other debris inside the unit may cause damage. The unit should be regularly serviced or cleaned (no guarantee) depending on ambient conditions (dust etc., nicotine, fog) by qualified personnel to prevent overheating and malfunction.

34. Please keep a distance of at least 0.5 m to any combustible materials.

35. Power cables to power multiple devices must have a cross-section of at least 1.5 mm². Within the EU, the cables must correspond to H05VV-F, or similar. Suitable cables are offered by Adam Hall. With these cables, you can connect multiple devices via the power OUT connection to the power IN connection of an additional device. Make sure that the total current consumption of all connected devices does not exceed the specified value on all connected devices (label on the device). Make sure to keep power cable connections as short as possible.

CAUTION:
To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable parts inside. Maintenance and repairs should be exclusively carried out by qualified service personnel.
The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an electrical shock.
The warning triangle with exclamation mark indicates important operating and maintenance instructions.
Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot during operation. After use, wait for a cool-down period of at least 10 minutes before handling or transporting the device.
Warning! This device is designed for use below 2000 meters in altitude.
Warning! This product is not intended for use in tropical climates.
Caution! Intense LED light source! Risk of eye damage. Do not look into the light source.
CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS!

1. The product has been developed for professional use in the field of event technology and is not suitable as household lighting.
2. Do not stare, even temporarily, directly into the light beam.
3. Do not look at the beam directly with optical instruments such as magnifiers.
4. Stroboscope effects may cause epileptic seizures in sensitive people! People with epilepsy should definitely avoid places where strobes are used.

INTRODUCTION

The Cameo MovoBeam Zoom 100 is an ultra-fast moving head with zoom function, unlimited pan and tilt movement, 16-bit resolution and a 1000 Hz refresh rate. A 60-watt quad LED generates rich RGBW colours, fresh pastels and vibrant shades of white with a 4° to 30° beam angle and a light intensity of 8500 lux a distance of three metres.
CONTROL FUNCTIONS:
5-channel, 16-channel, 21-channel, 36-channel DMX control Master / slave mode Standalone functions
FEATURES:
1 x high-power 60 W COB RGBW LED. RGBW colour mix. Zoom function with 4° – 30° dispersion. 2 high-speed motors for pan and tilt. Endless pan and tilt motion. Suitable for TV and video due to 1000 Hz refresh rate. DMX-512 control. Master / slave mode. Standalone programmes. Operating voltage 100 – 240 V AC / 50 – 60 Hz. Power consumption 140 W. Omega mounting bracket included.
CONNECTIONS, OPERATING AND DISPLAY ELEMENTS

1. OWER IN
   Blue mains input socket. Operating voltage 100 – 240 V AC / 50 – 60Hz. Connection using the power cable supplied.

2. POWER OUT
   White power output socket. Facilitates power supply to other CAMEO lights. Ensure that the total current consumption of all connected
   devices does not exceed the value specified on the device in amperes (A).

3. DMX IN
   Male 3-pin XLR socket for connection to a DMX control device (e.g. DMX console).

4. DMX OUT
   Female 3-pin XLR socket for sending the DMX control signal.

5. ILLUMINATED GRAPHIC DISPLAY
   Displays the current operating mode and other system settings.

6. CONTROLS
   MODE
   Press MODE to access the system settings selection menu. Press repeatedly to go back to the main display.
   UP and DOWN
   Select individual items in the selection menu and sub-menus for system settings (DMX address, operating mode etc.). These controls allow changes to be made to the value of a menu item as required, e.g. the DMX address.
   ENTER
   Press ENTER to access sub-menus in the selection menu so as to be able to make changes to the settings. Confirm changes by pressing ENTER.

OPERATION

NOTE
When the lamp is correctly connected to the mains supply, “Welcome to Cameo” and the software version are shown on the display during start-up and motor reset. Once this process is complete, the spotlight is ready for operation and the previously selected operating mode is activated.
MAIN DISPLAY DMX MODE
The DMX mode (DMX 5 Ch, 16 Ch, 21 Ch, 36 Ch) is shown in the top line of the display with the DMX start address clearly visible at the centre (in the example: DMX 36 Ch and ADDRESS 001). As soon as the DMX signal is interrupted, the display begins to flash. When there is a DMX signal again, the display will stop flashing. MAIN DISPLAY SLAVE MODE
The preset DMX mode is shown in the top line of the display with “SLAVE” clearly visible at the centre. As soon as the control signal is interrupted, the display begins to flash. When there is a signal again, the display will stop flashing. MAIN DISPLAY STANDALONE MODE
The preset DMX mode is shown in the top line of the display with the currently activated auto mode (AUTO1 – AUTO8) or the static mode STATIC clearly visible at the centre.

SET DMX START ADDRESS (ADDRESS)
Press MODE to access the system settings selection menu. Now use UP and DOWN to select the menu item “ADDRESS” (shaded in colour) and confirm with ENTER. The sub-menu item “Set DMX Address” is then displayed. Press ENTER again to set the DMX start address as required using UP and DOWN. If the start address is changed, the colour of the address changes to red. Confirm with ENTER and press MODE twice to return to the main display.
The main display is activated automatically after approximately 30 seconds of no input. SET DMX MODE (DMX Mode)
Press MODE to access the system settings selection menu. Now use UP and DOWN to select the menu item “MODE” (shaded in colour) and confirm with ENTER. Use UP and DOWN once again to select the sub-menu item “DMX Mode” and confirm with ENTER. Now use UP and DOWN to select the required DMX mode (DMX 5 Ch, DMX 16 Ch, DMX 21 Ch, DMX 36 Ch) and confirm with ENTER. Press MODE twice to return to the main display . The main display is activated automatically after approximately 30 seconds of no input. Tables with the channel assignment of the different DMX modes can be found in these instructions under DMX CONTROL. SET SLAVE MODE (Slave)
Press MODE to access the system settings selection menu. Now use UP and DOWN to select the menu item “MODE” (shaded in colour) and confirm with ENTER. Use UP and DOWN once again to select the sub-menu item “Slave”, confirm with ENTER and press MODE twice to return to the main display. The main display is activated automatically after approximately 30 seconds of no input. Connect the slave and master units (same model) using a DMX cable, and enable one of the standalone modes on the master unit (Auto, Static). The slave unit will now follow the master unit. SET AUTOMATIC CONTROL MODE (Auto)
Press MODE to access the system settings selection menu. Use UP and DOWN to select the menu item “MODE” (shaded in colour) and confirm with ENTER. Use UP and DOWN once again to select the sub-menu item “Auto” and confirm with ENTER. Now use UP and DOWN to choose between two other sub-menu items – “Auto Prog” and “Auto Speed”. Select “Auto Prog”, press ENTER, choose one of the eight different auto programmes (Prog1 – Prog8) and confirm with ENTER. To set the programme speed, select the menu item “Auto Speed” using UP and DOWN, confirm with ENTER and then use UP and DOWN again to select the desired speed from 000 to 255 (000 = fastest speed, 255 = slowest speed). Confirm with ENTER and press MODE three times to return to the main display. The main display is activated automatically after approximately 30 seconds of no input. STATIC MODE (Static)
The static mode allows all functions such as pan, tilt, dimmer and stroboscope to be set directly on the device with values between 000 and 255, as with a DMX controller. In this way, an individual scene can be created without the need for an additional DMX controller. Press MODE to access the system settings selection menu. Use UP and DOWN to select the menu item “Static” (shaded in colour) and confirm with ENTER. Use UP and DOWN to select the moving heads function you wish to edit and confirm with ENTER. The value (pan position, dimmer etc., see list) of the function in question can now be set from 000 to 255 and confirmed with ENTER. Once all functions have been set as required, press MODE three times to return to the main display. The main display is activated automatically after approximately 30 seconds of no input.

STATIC

Pan| 0| –| 255| 0% to 100%
Pan fine| 0| –| 255| 0% to 100%
Endless Pan| 0| –| 5| No function
6| –| 126| Forward rotation fast -> slow
127| –| 128| Stop
129| –| 255| Backward rotation slow -> fast
Tilt| 0| –| 255| 0% to 100%
Tilt fine| 0| –| 255| 0% to 100%
Endless lilt| 0| –| 5| No function
6| –| 126| Forward rotation fast -> slow
127| –| 128| Stop
129| –| 255| Backward rotation slow -> fast
Dimmer| 0| –| 255| 0% to 100%
Strobe| 0| –| 5| Strobe open
---|---|---|---|---
6| –| 10| Strobe closed
11| –| 33| Puls Random, slow -> fast
34| –| 56| Ramp up Random, slow -> fast
57| –| 79| Ramp down Random, slow -> fast
80| –| 102| Random Strobe Effect, slow -> fast
103| –| 127| Strobe Break Effekt, 5s…..1s (Short burst with break)
128| –| 250| Strobe slow -> fast <1Hz – 20Hz
251| –| 255| Strobe open
Red| 0| –| 255| 0% to 100%
Green| 0| –| 255| 0% to 100%
Blue| | –| 255| 0% to 100%
White| 0| –| 255| 0% to 100%
Zoom| 0| –| 255| 0% to 100%
Ring Macro| 0| –| 5| Colour off
6| –| 13| Colour Macro 1 (Colour Jump)
14| –| 21| Colour Macro 2 (Red 1 Step)
22| –| 29| Colour Macro 3 (Green 1 Step)
30| –| 37| Colour Macro 4 (Blue 1 Step)
38| –| 45| Colour Macro 5 (Yellow 1 Step)
46| –| 53| Colour Macro 6 (Cyan 1 Step)
54| –| 61| Colour Macro 7 (Magenta 1 Step)
62| –| 69| Colour Macro 8 (2step Magenta Yellow)
70| –| 77| Colour Macro 9 (2step Red Green)
78| –| 85| Colour Macro 10 (2step Red Blue)
86| –| 93| Colour Macro 11 (2step Blue Yellow)
94| –| 101| Colour Macro 12 (2step Green Blue)
102| –| 109| Colour Macro 13 (2step Magenta Blue)
110| –| 117| Colour Macro 14 (2step Green Yellow)
118| –| 125| Colour Macro 15 (2step Cyan Magenta)
126| –| 133| Colour Macro 16 (2step Cyan Red)
134| –| 255| No function
Ring Macro Speed| 0| –| 255| slow -> fast

DEVICE SETTINGS (Setting)
Press MODE to access the system settings selection menu. Use UP and DOWN to select the menu item “Setting” (shaded in colour) and confirm with ENTER. This will take you to the sub-menu for configuring the sub-menu items (see list, select using UP and DOWN, confirm with ENTER). The main display is activated automatically after approximately 30 seconds of no input.

Setthvg

Display Rev| =| Flip display| ON| = Rotate display by 180° (e.g. for overhead installation)
OFF| = No display rotation
Display| =| Display lighting| ON| = Permanently on
OFF| = Deactivation after one minute of inactivity
DMX Fail| =| Operating status with DMX
signal fault| Hold| = Last command is retained
---|---|---|---|---
or black- out,| = Activates blackout
Auto| = Activates auto mode
Dimmer Curve| =| Dimmer curve| Linear| = Light intensity increases linearly with DMX value
rvn 1| = Light intensity can be finely adjusted at lower DMX values and broadly adjusted at higher DMX values
1 nn Lo| = Light intensity can be broadly adjusted at lower DMX values and finely adjusted at higher DMX values
S Curve| = Light intensity can be finely adjusted at lower and higher DMX values and broadly adjusted at medium DMX values
Pan Rev| =| Pan Reverse| Normal| = No reversal of pan direction
Reverse| = Reversal of pan direction
lilt Rev| =| lilt reverse| Normal| = No reversal of tilt direction
Reverse| = Reversal of tilt direction
Feedback| =| Position correction| ON| = Automatic position correction activated
OFF| = Automatic position correction deactivated
Fan Control| =| Fan speed| Regular| = Maximum brightness with normal fan function
Silent| = If necessary, reduced brightness with quiet fan
Mov Blackout| =| Automatic blackout in the
event of head movement| ON| = Blackout in the event of head movement
OFF| = No blackout in the event of head movement
Calibrate| | Correction of head position
forpan and tiff| Pan| Position correction from -128 to +127
Tilt| Position correction from -128 to +127
TEST| =| Function test| OFF| = Stop function test
ON| = Step-by-step function test of LEDs and motors (approx. 30 seconds)
Reset| =| Reset| Pan & Tilt| Reset pan and tilt motors
Head| = Reset the device head
All| = Reset all motors and settings

DIMMER CURVES DEVICE INFORMATION (System Info)
Press MODE to access the system settings selection menu. Now use UP and DOWN to select the menu item “System Info” (shaded in colour) and confirm with ENTER. This will take you to the sub-menu for displaying the device information. Use UP and DOWN again to select the required sub-menu item, then access the information with ENTER.

System Info

Software Ver| =| Displays device software version| | VR. xx
Temp info| =| Displays temperature of LED unit| LED Temp| xxC / xxF
Temp Unit| Celsius (= temperature in Celsius)
Fahrenheit (= temperature in Fahrenheit)
Time info| =| Operating time display| Power on| Displays total operating time in hours
Last Run Hrs| Displays operating time since the last time the device was switched on

Press MODE several times to return to the main display. The main display is activated automatically after approximately 30 seconds of no input.

INSTALLATION AND MOUNTING

Thanks to its integrated rubber feet, the spotlight can be positioned in a suitable location on the stage floor etc.
The device can be installed on a traverse using the Omega bracket supplied (only use the original mounting bracket); attach the device securely at the specified position (A) using a suitable safety cable. Important: Overhead installation may only be carried out by qualified personnel. DMX TECHNOLOGY
DMX-512
DMX (Digital Multiplex) is the designation for a universal transmission protocol for communications between corresponding devices and controllers. A DMX controller sends DMX data to the connected DMX device(s). The DMX data is always transmitted as a serial data stream that is forwarded from one connected device to the next via the “DMX IN” and “DMX OUT” connectors (XLR plug-type connectors) that are found on every DMX-capable device, provided the maximum number of devices does not exceed 32 units. The last device in the chain needs to be equipped with a terminator (terminating resistor).
DMX CONNECTION
DMX is the common “language” via which a very wide range of types and models of equipment from various manufacturers can be connected with one another and controlled via a central controller, provided that all of the devices and the controller are DMX compatible. For optimum data transmission, it is necessary to keep the connecting cables between the individual devices as short as possible. The order in which the devices are integrated in the DMX network has no influence on the addresses. Thus the device with the DMX address 1 can be located at any position in the (serial) DMX chain: at the beginning, at the end or somewhere in the middle. If the DMX address 1 is assigned to a device, the controller “knows” that it should send all data allocated to address 1 to this device regardless of its position in the DMX network.
SERIAL CONNECTION OF MULTIPLE LIGHTS

1. Connect the male XLR connector (3-pin or 5-pin) of the DMX cable to the DMX output (female XLR socket) of the first DMX device (e.g. DMX-Controller).
2. Connect the female 3-pin XLR connector of the DMX cable connected to the first projector to the DMX input (male 3-pin socket) of the next DMX device. In the same way, connect the DMX output of this device to the DMX input of the next device and repeat until all devices have been connected. Please note that as a rule, DMX devices are connected in series and connections cannot be shared without active splitters. The maximum number of DMX devices in a DMX chain should not exceed 32 units. The Adam Hall 3 STAR, 4 STAR, and 5 STAR product ranges include an extensive selection of suitable cables.

DMX CABLES
When fabricating your own cables, always observe the illustrations on this page. Never connect the shielding of the cable to the ground contact of the plug, and always make certain that the shielding does not come into contact with the housing of the XLR plug. If the shielding is connected to the ground, this can lead to short-circuiting and system malfunctions.
Pin Assignment
DMX TERMINATORS (TERMINATING RESISTORS)

• To prevent system errors, the last device in a DMX chain needs to be equipped with a terminating resistor (120 ohm, 1/4 Watt).
• 3-pin XLR connector with a terminating resistor: K3DMXT3
• 5-pin XLR connector with a terminating resistor: K3DMXT5

Pin Assignment
DMX ADAPTER
The combination of DMX devices with 3-pin connectors and DMX devices with 5-pin connectors in a DMX chain is possible with suitable adapters.
Pin Assignment
DMX Adapter 5-pin XLR male to 3-pin XLR female: K3DGF0020 Pins 4 and 5 are not used. Pin Assignment
DMX Adapter 3-pin XLR male to 5-pin XLR female: K3DHM0020 Pins 4 and 5 are not used.

TECHNICAL DATA

auto programmes, stroboscope, RGBW, dimmer, dimmer fine, colour macros, zoom, colour ring colour macros, colour ring colour macro speed, stroboscope colour ring, dimmer curves
Standalone functions:| auto programmes, static mode, master/slave

MANUFACTURER’S DECLARATIONS
MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY
Adam Hall GmbH, Adam-Hall-Str. 1, 61267 Neu Ansbach, Germany / E-mail Info@adamhall.com / +49 (0)6081 / 9419-0.
Our current warranty conditions and limitation of liability can be found at:
https://cdn-shop.adamhall.com/media/pdf/Manufacturers-Declarations- CAMEO_DE_EN_ES_FR.pdf.
Contact your distribution partner for service.
UKCA- CONFORMITY
Hereby, Adam Hall Ltd. declares that this product meets the following guidelines (where applicable)
Electrical Equipment (Safety) Regulations 2016
Electromagnetic Compatibility Regulations 2016 (SI 2016/1091)
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation 2012 (SI 2012/3032) Radio Equipment Regulations 201 7(SI 2016/2015)
UKCA- DECLARATION OF CONFORMITY
Products that are subject to Electrical Equipment(Safety)Regulation 2016, EMC Regulation 2016 or RoHS Regulation can be requested at info@adamhall.com.
Products that are subject to the Radio Equipment’s Regulations 2017 (SI2017/1206) can be downloaded from www.adamhall.com/compliance/

DMX CONTROL

5 CH Mode|
---|---
Ch.| Function| Values| Sub-Group
1| Dimmer| 000 – 255 0% to 100%| Dimmer
2| Strobe| 000 – 005 Strobe open| Strobe
006 – 255 Strobe slow -> fast <1Hz – 20Hz
3| Zoom| 000 – 255 0% to 100%| Zoom
4| Auto Program| 000 – 005 off| Auto Program
006 – 036 Auto Program 1
037 – 067 Auto Program 2
068 – 098 Auto Program 3
099 – 129 Auto Program 4
130 – 160 Auto Program 5
161 – 191 Auto Program 6
192 – 222 Auto Program 7
223 – 255 Auto Program 8
5| Pan/Tilt Speed (Set Speed
Auto Programs)| 000 – 255 Pan/Tilt Fast -> Slow| Pan/Tilt speed
16 CH Mode

Ch.| Function| Values| Sub-Group
1| Pan| 000 – 255 0% to 100%| pan
2| Pan fine| 000 – 255 0% to 100%
3| Endless Pan rotation| 000 – 005 no function| Endless Pan
006 – 126 clockwise pan rotation (fast to slow)
127 – 128 no movement
129 – 255 counter clockwise pan rotation (slow to fast)
4| Tilt| 000 – 255 0% to 100%| Tilt
5| Tilt fine| 000 – 255 0% to 100%
6| Endless Tilt rotation| 000 – 005 no function| Endless lilt
006 – 126 clockwise tilt rotation (fast to slow)
127 – 128 no movement
129 – 255 counter clockwise tilt rotation (slow to fast)
7| Dimmer| 000 – 255 0% to 100%| Dimmer
8| Strobe functions| 000 – 005 Strobe open| multifunctional strobe
006 – 010 Strobe closed
011 – 033 Pulls Random, slow -> fast
034 – 056 Ramp up Random, slow -> fast
057 – 079 Ramp down Random, slow -> fast
080 – 102 Random Strobe Effect, slow -> fast
103 – 127 Strobe Break Effect, 5s…..1s (Short burst with break)
128 – 250 Strobe slow -> fast <1Hz – 20Hz
251 – 255 Strobe open
9| Red| 000 – 255 0% to 100%| Red
10| Green| 000 – 255 0% to 100%| Green
11| Blue| 000 – 255 0% to 100%| Blue
12| White| 000 – 255 0% to 100%| White
13| Zoom| 000 – 255 0% to 100%| Zoom
14| Device settings| 000 – 005 no function| Device settings
---|---|---|---
006 – 032 Blackout while Moving on (Hold 3s)
033 – 059 Blackout while Moving off (Hold 5s)
060 – 086 Invert Pan on (Hold 3s)
087 – 113 Invert Pan off (Hold 55)
114 – 140 Invert Tilt on (Hold 35)
141 – 167 Invert Tlt off (Hold 5s)
168 – 194 Silent Fan on (Hold 3s)
195 – 221 Silent Fan off (Hold 5s)
222 – 255 Reset All Functions (Hold 3s)
15| Colour Ring Macro| 000 – 005 Colour off| Colour Ring Macro
006 – 013 Colour Macro 1 (Colour Jump)
014 – 021 Colour Macro 2 (Red 1 Step)
022 – 029 Colour Macro 3 (Green 1 Step)
030 – 037 Colour Macro 4 (Blue 1 Step)
038 – 045 Colour Macro 5 (Yellow 1 Step)
046 – 053 Colour Macro 6 (Cyan 1 Step)
054 – 061 Colour Macro 7 (Magenta 1 Step)
062 – 069 Colour Macro 8 (2step Magenta Yellow)
070 – 077 Colour Macro 9 (2step Red Green)
078 – 085 Colour Macro 10 (2step Red Blue)
086 – 093 Colour Macro 11 (2step Blue Yellow)
094 – 101 Colour Macro 12 (2step Green Blue)
102 – 109 Colour Macro 13 (2step Magenta Blue)
110 – 117 Colour Macro 14 (2step Green Yellow)
118 – 125 Colour Macro 15 (2step Cyan Magenta)
126 – 133 Colour Macro 16 (2step Cyan Red)
16| Colour Ring Macro Speed| 000 – 255 slow > fast| Colour Ring Macro Speed
21 CH Mode|
---|---
Ch.| Function| Values| Sub-Group
1| Pan| 0| –| 255| 0% to 100%| Pan
2| Pan fine| 0| –| 255| 0% to 100%
3| Endless Pan rotation| 0| –| 5| no function| Endless Pan
6| –| 126| clockwise pan rotation (fast to slow)
127| –| 128| no movement
129| –| 255| counter clockwise pan rotation (slow to fast)
4| Tilt| 0| –| 255| 0% to 100%| Tilt
5| Tilt fine| 0| –| 255| 0% to 100%
6| Endless Tilt rotation| 0| –| 5| no function| Endless Tilt
6| –| 126| clockwise tilt rotation (fast to slow)
127| –| 128| no movement
129| –| 255| counter clockwise tilt rotation (slow to fast)
7| Dimmer| 0| –| 255| 0% to 100%| Dimmer
8| Strobe Functions| 0| | 5| Strobe open| Multifunctional
Strobe
---|---|---|---|---|---|---
6| | 10| Strobe closed
11| –| 33| Pulse Random, slow -> fast
34| –| 56| Ramp up Random, slow -> fast
57| –| 79| Ramp down Random, slow -> fast
80| –| 102| Random Strobe Effect, slow -> fast
103| –| 127| Strobe Break Effect, 5s…..1s (Short burst with break)
128| | 250| Strobe slow -> fast <1Hz – 20Hz
251| | 255| Strobe open
9| Red| 0| –| 255| 0% to 100%| Red
10| Green| 0| –| 255| 0% to 100%| Green
11| Blue| 0| | 255| 0% to 100%| Blue
12| White| 0| –| 255| 0% to 100%| White
13| Zoom| 0| –| 255| 0% to 100%| Zoom
14| Device settings| 0| –| 5| no function| Device settings
6| | 32| Blackout while Moving on (Hold 3s)
33| | 59| Blackout while Moving off (Hold 5s)
60| | 86| Invert Pan on (Hold 3s)
87| –| 113| Invert Pan off (Hold 5s)
114| –| 140| Invert Tilt on (Hold 3s)
141| –| 167| Invert Tilt off (Hold 5s)
168| –| 194| Silent Fan on (Hold 3s)
195| –| 221| Silent Fan off (Hold 5s)
222| –| 255| Reset All Functions (Hold 3s)
15| Dimmer Colour Ring| 0| –| 255| 0% to 100%| Dimmer
16| Strobe Colour Ring| 0| | 5| Strobe open| Strobe
6| | 255| Strobe slow -> fast <1Hz – 20Hz
17| Colour Red| 0| | 255| 0% to 100%| Colour Ring
18| Colour Green| 0| –| 255| 0% to 100%
19| Colour Blue| 0| –| 255| 0% to 100%
20| Colour Ring Macro| 0| –| 5| Colour off| Colour Ring Macro
6| –| 13| Colour Macro 1 (Colour Jump)
14| –| 21| Colour Macro 2 (Red 1 Step)
22| –| 29| Colour Macro 3 (Green 1 Step)
30| –| 37| Colour Macro 4 (Blue 1 Step)
38| | 45| Colour Macro 5 (Yellow 1 Step)
46| | 53| Colour Macro 6 (Cyan 1 Step)
54| | 61| Colour Macro 7 (Magenta 1 Step)
62| | 69| Colour Macro 8 (2step Magenta Yellow)
70| –| 77| Colour Macro 9 (2step Red Green)
78| | 85| Colour Macro 10 (2step Red Blue)
86| | 93| Colour Macro 11 (2step Blue Yellow)
94| –| 101| Colour Macro 12 (2step Green Blue)
102| –| 109| Colour Macro 13 (2step Magenta Blue)
110| –| 117| Colour Macro 14 (2step Green Yellow)
118| –| 125| Colour Macro 15 (2step Cyan Magenta)
126| –| 133| Colour Macro 16 (2step Cyan Red)
21| Colour Ring Macro Speed| 0| –| 255| slow > fast Colour Ring Macro| Speed
36 CH Mode

Ch.| Function| Values| Sub-Group
1| Pan| 000 – 255 0% to 100%| Pan
2| Pan fine| 000 – 255 0% to 100%
3| Endless Pan rotation| 000 – 005 no function| Endless Pan
006 – 126 clockwise pan rotation (fast to slow)
127 – 128 no movement
129 – 255 counter clockwise pan rotation (slow to fast)
4| Tilt| 000 – 255 0% to 100%| Tilt
5| Tilt fine| 000 – 255 0% to 100%
6| Endless Tilt rotation| 000 – 005 no function| Endless Tilt
006 – 126 clockwise tilt rotation (fast to slow)
127 – 128 no movement
129 – 255 counter clockwise tilt rotation (slow to fast)
7| Dimmer| 000 – 255 0% to 100%| Dimmer
8| Dimmer fine| 000 – 255 0% to 100%
9| Strobe functions| 000 – 005 Strobe open| multifunctional strobe
006 – 010 Strobe closed
011 – 033 Pulls Random, slow -> fast
034 – 056 Ramp up Random, slow -> fast
057 – 079 Ramp down Random, slow -> fast
080 – 102 Random Strobe Effect, slow -> fast
103 – 127 Strobe Break Effect, 5s…..1s (Short burst with break)
128 – 250 Strobe slow -> fast <1Hz – 20Hz
251 – 255 Strobe open
10| Red| 000 – 255 0% to 100%| Red
11| Green| 000 – 255 0% to 100%| Green
12| Blue| 000 – 255 00/0 to 100%| Blue
13| White| 000 – 255 00/0 to 100%| White
14| Colour Macro (override RGBW)| 000 – 005 Colour off| Colour Macro
006 – 013 Red
014 – 021 Amber
022 – 029 Yellow warm
030 – 037 Yellow
038 – 045 Green
046 – 053 Turquoise
054 – 061 Cyan
062 – 069 Blue
070 – 077 Lavender
078 – 085 Mauve
086 – 093 Magenta
094 – 101 Pink
102 – 109 Warm White
110 – 117 White
118 – 125 Cold White
126 – 127 Colour Jumping Stop
128 – 191 Colour Jumping Speed slow -> fast / Colour 1 -> 12
192 – 255 Colour Fading Speed slow -> fast / Colour 1 -> 12
15| Zoom| 000 – 255 0% to 100%| Zoom
16| Auto Program| 000 – 005 off| Auto Program
---|---|---|---
006 – 036 Auto Program 1
037 – 067 Auto Program 2
068 – 098 Auto Program 3
099 – 129 Auto Program 4
130 – 160 Auto Program 5
161 – 191 Auto Program 6
192 – 222 Auto Program 7
223 – 255 Auto Program 8
17| Pan/Tilt Macro| 000 – 005 off| Auto Movement
006 – 040 PAN „small > big”
041 – 075 TILT „small > big”
076 – 110 PAN / TILT „small > big”
111 – 145 PAN / TILT (invers) „small > big”
146 – 180 Circle „small > big”
181 – 215 Circle (invers) „small > big”
216 – 255 Random „small > big”
18| Set dimmer curve| 000 – 005 no function| Set dimmer curve
006 – 063 Linear Dimmer Curve
064 – 127 Exponential Dimmer Curve
128 – 191 Logarithmic Dimmer Curve
192 – 255 S-Curve Dimmer Curve
19| Pan/Tilt Speed (Set Speed of
Pan Tilt / Auto Programs /
Pan Tilt Macros)| 000 – 255 Pan/Tilt Fast -> Slow| Pretilt speed
20| Device settings| 000 – 005 no function| Device settings
006 – 032 Blackout while Moving on (Hold 3s)
033 – 059 Blackout while Moving off (Hold 5s)
060 – 086 Invert Pan on (Hold 3s)
087 – 113 Invert Pan off (Hold 5s)
114 – 140 Invert Tilt on (Hold 3s)
141 – 167 Invert Tilt off (Hold 5s)
168 – 194 Silent Fan on (Hold 3s)
195 – 221 Silent Fan off (Hold 5s)
222 – 255 Reset All Functions (Hold 3s)
21| Dimmer Colour Ring| 000 – 255 0% to 100%| Dimmer
22| Strobe Colour Ring| –
000 005 Strobe open| Strobe
006 – 255 Strobe slow -> fast <1Hz – 20Hz
23| Red1| 000 – 255 0% to 100°/0|
24| Green1| 000 – 255 0% to 100%
25| Blue1| 000 – 255 0% to 100%
26| Red2| 000 – 255 0% to 100%
27| Green2| 000 – 255 0% to 100%
28| BIue2| 000 – 255 0% to 100°/0
29| Red3| Colour Ring 000 – 255 0% to 100%
30| Green3| 000 – 255 0% to 100%
31| BIue3| 000 – 255 0% to 100°/0
32| Red4| 000 – 255 0% to 100°/0
33| Green4| 000 – 255 0% to 100%
34| BIue4| 000 – 255 0% to 100%
35| Colour Ring Macro (override RGB)| 000 – 005 Colour off| Colour Ring Macro
---|---|---|---
006 – 013 Colour Macro 1 (Colour Jump)
014 – 021 Colour Macro 2 (Red 1 Step)
022 – 029 Colour Macro 3 (Green 1 Step)
030 – 037 Colour Macro 4 (Blue 1 Step)
038 – 045 Colour Macro 5 (Yellow 1 Step)
046 – 053 Colour Macro 6 (Cyan 1 Step)
054 – 061 Colour Macro 7 (Magenta 1 Step)
062 – 069 Colour Macro 8 (2step Magenta Yellow)
070 – 077 Colour Macro 9 (2step Red Green)
078 – 085 Colour Macro 10 (2step Red Blue)
086 – 093 Colour Macro 11 (2step Blue Yellow)
094 – 101 Colour Macro 12 (2step Green Blue)
102 – 109 Colour Macro 13 (2step Magenta Blue)
110 -117 Colour Macro 14 (2step Green Yellow)
118 – 125 Colour Macro 15 (2step Cyan Magenta)
126 – 133 Colour Macro 16 (2step Cyan Red)
36| Colour Ring Macro Speed| 000 – 255 slow > fast| Colour Ring Macro Speed

Adam Hall GmbH
Adam-Hall-Str. 1 | 61267 Neu-Ansbach | Germany
Phone: +49 6081 9419-0
adamhall.com
Adam Hall Ltd.
The Seedbed Business Centre
SS3 9QY Essex
United Kingdom

References

• Eventtechnik Lösungen | Adam Hall Group
• Cameo® | For Lumen Beings
• Eventtechnik Lösungen | Adam Hall Group
• Cameo® | For Lumen Beings
• cdn-shop.adamhall.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>