COSMO UMC30 Under Cabinet Range Hood User Manual

COSMO UMC30 Under Cabinet Range Hood

Under Cabinet Range Hood

UC & UMC series

Installation Guide
Thank you for purchasing our Under Cabinet Range Hood. This appliance is intended for normal indoor residential use. Please note that it is not approved for commercial use, outdoor
installation, installation over an outdoor BBQ grill, or any other application not specifically allowed by this manual. Damage from improper installation or use of this appliance is not covered by the product warranty. Please read and save these instructions.

Parts Included

The package includes all the necessary parts for installation. Please refer to the parts diagram for your specific model:

• UC30 / UMC30
• UC36 / UMC36

Pre-Installation Requirements

Please ensure that you have the following before starting the installation process:

• Electrical power supply with grounding
• Screwdrivers (Phillips and flathead)
• Tape measure
• Pencil or marker
• Drill with 1/8″ bit
• Jigsaw or reciprocating saw

Installation Instructions

Please follow the instructions carefully to ensure proper installation:

1. Turn off the electrical power supply.
2. Remove the old range hood (if applicable).
3. Attach the mounting bracket to the wall using screws and a drill.
4. Run electrical wiring through the bracket and connect it to the hood’s electrical wiring.
5. Install the hood onto the mounting bracket and secure it in place with screws.
6. Connect the ductwork to the hood and route it to the outside of the house.
7. Turn on the electrical power supply and test the range hood.

Operating Instructions

To operate the range hood, follow these instructions:

1. Turn on the electrical power supply.
2. Select the desired fan speed.
3. Use the light switch to turn on/off the hood’s lights.

Recirculating Charcoal Filters

If you are using recirculating charcoal filters, follow these instructions:

1. Remove the ARC-FLOW Baffle Filters.
2. Locate the motor and align one of the filters with the right side of the motor.
3. Twist and lock the filter into place.
4. Repeat steps 2-3 on the left side of the motor.
5. Reinstall the ARC-FLOW Baffle Filters back into place.

Note: Chimney vent holes must be open and visible for the filtered air to recirculate.

Maintenance

We recommend replacing the charcoal filter every 4-6 months. Charcoal filter replacements are available for purchase on our website. Please refer to Charcoal Filter Kit Part# CFK1-TM.

Troubleshooting

If you experience any issues with your range hood, please refer to the troubleshooting section of this manual or contact our customer service department for assistance.

Technical Information

Please refer to the technical information section of this manual for more details about our UC & UMC series range hoods.

STAINLESS STEEL BAFFLE FILTERS

About Your New Filters
Stainless Steel Baffle Filters do not need linings or mesh inside of the filters and are completely constructed out of stainless steel. The stainless steel construction allows them to be used again after being cleaned or going through the dishwasher.

How do Baffle Filters Work?
They function by forcing the grease filled air to quickly and continuously change direction as it passes through the filter. The grease is unable to change direction as fast as the air carrying them, they end up getting caught on the metal blades and then trapped into the filter tray. These filters are both efficient and require less maintenance.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this appliance. Save these instructions for future references Approved for residential appliances For residential use only

CAUTION
TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS CAUTION To reduce risk of fire and to properly exhaust air, do not vent exhaust air into spaces within walls, ceilings, attics WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL
CAUTION
FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPORS.
CAUTION
This product is designed for indoor residential use only.
CAUTION
To reduce risk of fire and to properly exhaust air. do not vent exhaust air into spaces within wans, ceilings. attics. craw spaces, or garages.
WARNING
TO REDUCE THE RISK OF FIRE. USE ONLY METAL DUCT WORK. Install this hood in accordance with all requirements specified

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

• Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer
• Before servicing or cleaning the unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
• Installation Work and Electrical Wiring Must Be Done By Qualified Person(s) In Accordance With all Applicable Codes & Standards, Including Fire-rated Construction.
• Sufficient air is needed for proper combustion and exhausting of gases through the flue (Chimney) of fuel burning equipment to prevent back- drafting. Follow the heating equipment manufacturers guideline and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
• When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
• Ducted systems must always be vented to the outdoors.

WARNING
To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Hood With Any External Solid State Speed Control Device.

WARNING
GROUNDING INSTRUCTIONS: This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

WARNING – IMPROPER GROUNDING CAN RESULT IN A RISK OF ELECTRIC SHOCK
Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance.

WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:

• SMOTHER FLAMES with a close – fitting lid, cookie sheet, or other metal tray, then turn off the gas burner or the electric element. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
• NEVER PICK UP A FLAMING PAN – you may be burned. DO NOT USE ,WATER including wet dishcloths or towels a violent steam explosion will result.

Always leave safety grills and filters in place. Without these components, operating blowers could catch onto hair, fingers and loose clothing. The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance.

WARNING
Unplug or disconnect the appliance from the power supply before servicing.

WARNING
This appliance is intended for normal indoor residential use. It is not approved for commercial use, outdoor installation, installation over an outdoor BBQ grill, or any other application not specifically allowed by this manual. Damage from improper installation or use of this appliance is not covered by the product warranty.

PARTS DIAGRAM

PARTS INCLUDED

Parts Required

PRE-INSTALLATION REQUIREMENTS

1. Do not install the Range Hood where there are many doors or windows in order to avoid effecting the exhaust efficiency caused by air convection.
2. Install the Range hood directly above the cooking surface. The recommended distance between the cooking surface and the bottom of the range is minimum 24″ and Maximum 30″.
3. In order to get the optimum performance, do not extend the vent pipe too far , adjust the vent pipe, and make sure the hood is level and vertical.
4. The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must not be connected to ventilation ducts for rooms in which fuel-burning appliances are installed.

SAFETY WARNING
HOOD MAY HA VE SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF ITS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING, OR SERVICING.

INSTALLATION INSTRUCTIONS

1. Drill two 8mm holes in position for Wall Anchor (Part B) placement. (See Page 5 for placement location).

2. Tap Wall anchors securely into each of the drilled holes.

3. After Wall anchors have been tapped in place. Insert 4×30 screws, but leave 1/4of the screw sticking out of the wall. (This will give your Range Hood something to hang onto).
   

4. Take the hood unit along with the Round Aluminum duct (Part D). Secure the round aluminum duct to the vent hole at the top of the hood unit using HVAC Aluminum foil tape. If mounting to a cabinet, skip step 5 and proceed with steps 6-11.

5. If mounting to the wall only, drill a 6-1/4 round hole on the back wall above the hood, OR into the ceiling directly above the hood. 5a. Remove baffle filters from underneath the hood and set them aside. 5b. Lift the hood and hang the hood unit on the back wall using the screws drilled in Step 3. Once the hood is securely hung on the wall, tighten the screws from the interior of the hood. 5c. Pull round aluminum duct through the newly drilled hole in the wall. Plug unit into power outlet. Reinstall baffle filters.

6. Drill a 6 – 1/4Round Hole into the bottom of the cabinet. Drill a 1 – 1/2hole into the bottom of the cabinet for the Electrical Access hole. See Page 5 for hole location according to the diagram (Top View). 6a. Pull the round duct & power cord through the bottom of the new cabinet holes.

7. Lift the hood and hang the hood unit on the back wall using the screws drilled in Step 3.

8. Once the Hood is hung to the back wall, Remove the baffle filters from underneath the hood.

9. Drill each of the five pieces of 4×30 screws (Part C) into the bottom of the cabinet using the five screw holes at the top of the hood. 10. Once the hood is secured into the cabinet, tighten the wood screws located in the back of the hood. Install Baffle filters back into place. Make sure hood is secure by pressing on it. Plug unit into power outlet.

IMPORTANT SAFETY INSTRUCTIONS

• Please always supervise children and any other individuals that should be monitored while using this appliance.
• Do not connect the air outlet to chimney fuels or combustion gas ducts.
• Do not leave unattended open flames under this hood.
• In case of any damage to power cable, replace the broken cable with a new one by a qualified professional.
• Clean the hood as instructed in this manual. If the hood is not cleaned or cleaned improperly, it may cause fire, or the range hood may function incorrectly.
• The LED lamp should be replaced by a qualified professional. Always use a 2W LED light or less.
• Do not wash the control switch with water, as it will cause electrical issues for the range hood.
• Do not pull the plug from the power supply with wet hands to avoid electrical shock.
• Disconnect the hood from the power supply if the appliance will not be used for an extended period of time.

OPERATING INSTRUCTIONS
Push Button Controls COMPATIBLE MODELS: UC30 / UC36

How to use the Push Button:
Press to select on/off.
Press to select the low speed.
Press to select the medium speed.
Press to select the high speed.
Press to turn on /off the light.

Soft Touch Controls
COMPATIBLE MODELS: UMC30 / UMC36

• A. Light. Press to turn light on / off.
• B. Timer Button
• C. Minus Button (Fan Speed)
• D. Plus Button (Fan Speed)
• E. Fan Power Button (Starts Max Fan Speed)
• F. Power Button. Press to turn unit On/Off

Note: When Fan is ON + or – button will go to Min or Max Settings

Setting the Clock
Clock is in Military Time and cannot be changed.

1. Hold Timer Button for 3 Seconds Use Light Button (A) to set Minutes Use Fan Speed Button (E) to set Hours
2. Once time is set, Press Timer button to complete.
3. After setting the time, leave the unit alone for 5 seconds for the changes to save.

Setting the Timer

1. Turn fan on and set to desired fan speed.
2. Press the Timer Button (B). Continue tapping the Timer Button (B) to set the time duration before the fan should automatically turn off.
3. After setting the timer, leave the unit alone for 5 seconds for the changes to save and the timer will start counting down.

RECIRCULATING CHARCOAL FILTERS

Skip this page if you are installing a Ducted Range Hood. Charcoal Filters are only included with Ductless Models

Step 1: Remove the ARC-FLOW Baffle Filters.
Step 2: Locate the motor (pictured below\ and align one of the filters with the right side of the motor.

Step 3: Twist and lock the filter into place.
Step 4: Repeat Steps 2-3 on the left side of the motor.

Step 5: Reinstall the ARC-FLOW Baffle Filters back into place.
NOTE: Chimney vent holes must be opera and visible for the filtered air to recirculate.

A. Chimney hole                                     A. Roof cap
B. 6″ (15.2 cm) round vent                  B. 6″ (15.2 cm) round vent

It is recommended that the charcoal filter be replaced every 4-6 months. Charcoal filter replacements are available for purchase at: www.cosmoannliances.com Charcoal Filter Kit Part# CEK1_TM

MAINTENANCE
CAUTION
Never put your hand inside the unit while it is operating. For the best performance clean your unit frequently.

CLEANING

1. Use only mild soap or cleaning solutions to clean the range hoods outer surface. Dry surfaces using a soft cloth.
2. Stainless Steel cleaner may be used on the external surface.
3. Cleaning the Baffle Filters: For daily cleaning, use hot, soapy water and a soft cloth. Wipe dry and finish with a damp micro- fiber cloth. Baffle filters can also be cleaned in the dishwasher.
4. Clean the Range Hood assembly once every 6 months.
5. DO NOT clean motor or electrical components with water or any other liquid.

REPLACING LIGHT BULBS

CAUTION: LED LAMP UNIT IS HOT! WAIT BEFORE ATTEMPTING BEFORE ATTEMPTING TO REPLACE LED LAMPS. PLEASE BE SURE THE UNIT IS POWERED OFF & UNPLUGGED.
NOTE: INDIVIDUAL LED BULBS CANNOT BE REPLACED. ONLY LED LAMPS.

1. Remove the baffle filters
2. Find the wire connection of the lamp and unplug.
3. Remove old LED lamp.
4. Plug in new LED lamp.
5. Reinstall the baffle filters.

TROUBLESHOOTING
CAUTION: ALWAYS UNPLUG UNIT FROM POWER BEFORE SERVICING

and remove.
If your range hood is still noisy after checking, please call 1-888-784-3108.| Phillips Screwdriver
My range hood has poor performance|

• A.  The range hood and cooktop are too far away from each other.
  Optimal distance is 24″ to 36″

• B.  There are too many open windows or doors in the area. Close some doors or windows.

• C.  The motor performance has decreased due to wear. Replace motor.

• D.  Check and make sure the tape holding down the damper flaps at the vent hole are removed before use.

• E.  The filters are clogged and need to be cleaned.

| Phillips Screwdriver
My range hood shakes|

• A. The installation is not secure. Check again and make sure the installation hardware is securely mounted.
• B. The fan is broken or not balanced. Re-align or replace fan.
• C. The motor is loose. Check and make sure the motor is solidly mounted to the unit.
• D. Baffle filter is loose and is not installed correctly. Read page 12 for installation instructions.

| Phillips Screwdriver
Range Hood does not turn on|

• A. Make sure that range hood is plugged into powered outlet. Test outlet with other device if not working.
• B. Remove baffle filters, reach inside behind the control panel and locate the wire with clip. Make sure control panel is securely plugged in.

| Phillips Screwdriver
Light bulbs went out|

• A.  Replace with a new LED lamp assembly.
• B.  Remove baffle filters, reach inside behind the control panel and locate the wire with clip behind the light housing. Make sure the light is securely plugged in.

| Phillips Screwdriver

IF YOU HAVE TRIED ALL SOLUTIONS AND STILL EXPERIENCE ISSUES, PLEASE CALL SUPPORT: 1-888-784-3108.

TECHNICAL INFORMATION

IMPORTANT
Do Not Return This Product To The Store If you have a problem with this product, please contact Cosmo Customer Support at +1(888)784-3108 DATED PROOF OF PURCHASE, MODEL #, AND SERIAL # REQUIRED FOR WARRANTY SERVICE

Correct Disposal of this product
****This marking indicates that this appliance should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

WARRANTY AND SERVICE
For full warranty details on this product please visit: http://www.cosmoappliances.com/warranty TO RECEIVE WARRANTY SERVICE, YOUR PRODUCT MUST BE REGISTERED. TO REGISTER, VISIT: WWW.COSMOAPPLIANCES.COM/WARRANTY SCAN TO REGISTER
Electronic version of this manual is available at: www.cosmoappliances.com

References

• Cosmo Appliances | Luxury Ranges, Cooktops, Range Hoods

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>