cameo PHANTOM F5 High Power Fog Machine User Manual

: June 10, 2024
: cameo

Table of Contents

cameo PHANTOM F5 High Power Fog Machine
Product Information
Usage Instructions
SAFETY INFORMATION
INTRODUCTION
CONNECTIONS, CONTROL, AND DISPLAY ELEMENTS
OPERATION
- OPERATION BY CABLE REMOTE
SETUP AND INSTALLATION
TECHNICAL SPECIFICATIONS
MANUFACTURER´S DECLARATIONS
DMX CONTROL
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

cameo PHANTOM F5 High Power Fog Machine

cameo-PHANTOM-F5-High-Power-Fog-Machine-FEA

YOU HAVE MADE THE RIGHT CHOICE!
This device was developed and produced under the highest standards of quality in order to ensure smooth operation for many years. Please read these operating instructions carefully so that you can use your new Cameo Light product quickly and optimally. You can find more information on Cameo Light on our website WWW.CAMEOLIGHT.COM.

Product Information

The PHANTOM F5 is a high-power fog machine designed for use with water-based fog fluid. It comes equipped with 1-channel and 3-channel DMX control, allowing for easy integration with other lighting and audio equipment. A cable remote is also included for added convenience.

This fog machine operates on a voltage of 230 V AC/50-60 Hz and has a power consumption of 1450 W.

Usage Instructions

Before use, make sure the power cord is in good condition and properly connected to a suitable power source.
Fill the fog machine with water-based fog fluid according to the manufacturer’s instructions.
Connect the fog machine to a DMX controller or use the cable remote provided to operate the machine.
Turn on the fog machine and allow it to warm up for the recommended amount of time before use.
Adjust the fog output using the DMX controller or cable remote.
After use, turn off the fog machine and unplug it from the power source. Allow it to cool down before handling or transporting.

Important safety precautions:

Do not use the fog machine with any fluids other than water-based fog fluid.
Do not operate the fog machine in tropical climates or at altitudes above 2000 metres.
Keep the fog machine out of reach of children and do not allow them to play with it.
If the power cord becomes damaged, do not use the fog machine. Contact an authorized service center for a replacement cord.
Maintenance and repairs should only be carried out by qualified service personnel.

SAFETY INFORMATION

Please read through these instructions carefully.
Store all information and instructions in a secure location.
Follow the instructions.
Heed all warnings. Do not remove any safety warnings or other information from the device.
Use the device only in the intended manner.
Use only stable and suitable stands and/or mounts (for fixed installations). Make sure that wall mounts are properly installed and secured. Make sure that the device is securely installed and will not fall.
During installation, heed all safety provisions that apply in your country.
Do not install and operate the device in the vicinity of heaters, heat reservoirs, ovens, or other heat sources. Make sure that the device is installed in such a way that it is sufficiently cooled and will not overheat.
Do not place any ignition sources, e.g. candles, on the device.
Do not block the ventilation slits.
The device was designed to be used only in interior spaces, do not operate the device in the direct vicinity of water (this does not apply to specialty outdoor devices – in this case, please note the special instructions given in the following). Do not bring the device into contact with combustible materials, fluids, or gases.
Make sure that no water can drop or splash into the device. Do not place any containers filled with fluids, such as vases or drinking vessels, onto the device.
Ensure that no objects can fall into the device.
Operative the device using only those accessories recommended and specified by the manufacturer.
Do not open the device, and do not modify it.
After connecting the device, inspect all cable paths in order to avoid damage or accidents, such as those caused by tripping over said cables.
During transport, ensure that the device will not fall and potentially cause material damage and personal harm.
If your device no longer functions properly, fluids or objects have made their way into the device interior, or the device is otherwise damaged, switch it off immediately and remove it from the power outlet (provided the device is active). This device is to be repaired only by authorized specialists.
Use a dry towel to clean the device.
Follow all laws on disposal applicable in your country. Please separate plastic and paper or cardboard when disposing of the packaging.
Plastic bags must be kept out of reach of children.
FOR DEVICES CONNECTED TO A POWER SUPPLY:
ATTENTION: If the device power cable is equipped with a ground pin, it must be inserted into an outlet with a grounding conductor. Never disable the grounding conductor of a power cable.
Do not immediately switch on the device when it has been exposed to stark temperature deviations (for example after transport). Humidity and condensation could damage the device. Switch on the device only when it has reached room temperature.
Before you connect the device to the outlet, first ensure that voltage and frequency of the power supply complies with the values given on the device. If the device has a voltage selector switch, connect the device to the outlet only if the device values comply with the values of the power supply. If the provided power cable or power adapter does not fit your power outlet, contact an electrician.
Do not step on the power cable. Make sure that live cables, in particular those at the power socket or at the power adapter and the device socket, are not bent.
With regard to the device cables, always make sure that the power cable or power adapter is always freely accessible. Always separate the device from the power supply when the device is not in use or when you would like to clean the device. Always unplug the power cable and power adapter from the power outlet using the plug or adapter, not the cord. Never touch the power cable and power adapter with wet hands.
If possible, do not switch the device on and off quickly because this may impair the service life of the device.
IMPORTANT INFO: Replace fuses only with fuses of the same type and value. If a fuse trips repeatedly, please contact an authorized service center.
In order to completely separate the device from the power supply, remove the power cable or power adapter from the outlet.
If your device is equipped with a Volex power cord, release the correct Volex device connector before removing the cord. However, this also means that the device may slide and fall when removing the power cord, which may cause personal harm and/or material damage. Therefore, always lay cables carefully.
Remove the power cable and power adapter from the outlet when there is a risk of lighting or when you no longer want to use the device.
The device may only be installed when it carries no voltage (separate the power plug from the power supply).
Dust and other debris within the device may damage it. The device should be serviced or cleaned regularly by qualified specialists depending on the environmental conditions (dust, nicotine, smoke, etc.) in order to avoid overheating.
The distance to combustible materials must be at least 0.5 m.
Power cables for powering multiple devices must have a core cross-section of at least 1.5 mm². In the EU, lines must be H05VV-F or similar. Adam Hall provides suitable cables. Using these cables, you can connect multiple devices via the Power Out connection with the Power In connection of another device. Ensure that the total power consumption of all connected devices does not exceed the specified value (printed on the device). Be sure to keep power lines as short as possible.
The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
Children must be instructed not to play with the device.
If the power cord of the device is damaged, do not use the device. The power cord must be replaced by an adequate cable or assembly from an authorized service center.

CAUTION: To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable parts inside. Maintenance and repairs should be exclusively carried out by qualified service personnel.
The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an electrical shock.
The warning triangle with exclamation mark indicates important operating and maintenance instructions.
Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot during operation. After use, wait for a cool-down period of at least 10 minutes before handling or transporting the device.
Warning! This device is designed for use below 2000 metres in altitude.
Warning! This product is not intended for use in tropical climates.

CAUTION! IMPORTANT INFORMATION ON FOG MACHINES!

The device is specially developed for professional use in the area of event technology and is not suitable for household use!
Use only Cameo fog fluid (water-based) and never fill the canister with combustible fluids! Risk of explosion!
Disconnect the fog machine from the power supply before changing or filling the canister with fog fluid!
Only use the fog machine in well-ventilated spaces!
Never operate the fog machine unattended!
Separate the fog machine from the power supply before setup and installation, and make sure that the fog machine has cooled completely.
The fog output nozzle becomes very hot during use. Do not touch the output nozzle during use and keep a minimum distance of 50 cm! Before cleaning and transport, make sure that the device has cooled completely!
The discharged fog is very hot! Never aim the output nozzle at people or animals! BURN HAZARD!
Ensure that no people and animals are located directly below the fog machines! BURN HAZARD!
Never aim the fog outlet nozzle at open flames or combustible materials!
Ensure that other electrical devices and outlets are never directly exposed to the fog jet.
Fluid may collect via condensation in front of the fog outlet nozzle during use. Caution, slipping hazard!
Occasionally, small amounts of fog may escape during use even when not triggered, as well as a short time after switching off the fog machine.
Never expose persons with respiratory diseases (such as allergies, asthma) to artificial fog.
When using fog machines, ensure that visibility within the room does not sink below approx. 2 meters so that people can still safely orient themselves within the space.
Empty the fluid canister before transport.
The fog released can trigger smoke alarms.
Keep away from children!

INTRODUCTION

PROFESSIONAL FOG MACHINE
CLPHANTOMF5
CONTROL FUNCTIONS
1-channel and 3-channel DMX control
Cable remote
PROPERTIES
Professional fog machine for water-based fog fluid. DMX control. Cable remote included. Operating voltage 230 V AC / 50-60 Hz. Power consumption 1450 W.

CONNECTIONS, CONTROL, AND DISPLAY ELEMENTS

cameo-PHANTOM-F5-High-Power-Fog-Machine-7

POWER IN
Permanently connected power cable with CEE 7/7 power plug.
FUSE
Fuse holder for 5 x 20 mm micro fuses. IMPORTANT NOTE: Replace the fuse only with a fuse of the same type and values (see inscription on housing). If a fuse trips repeatedly, please contact an authorized service center.
ON / OFF
On or off switch for the device power supply.
REMOTE
Female 5-pin DIN jack for connection of the cable remote (included).
DMX IN
Male 3-pin XLR jack for connection of a DMX controller.
DMX OUT
Female three-pin XLR connector to transmit the DMX control signal.
LED DISPLAY
4-digit LED display for display of the DMX start address and other information.
CONTROL KEYS
- MODE – press MODE to go to the processing menu and press MODE again to show the DMX start address on the display.
- ENTER – press ENTER to go one level deeper in the processing menu and to confirm value or status changes.
- UP / DOWN – use the UP and DOWN buttons to change a value, such as the DMX start address or the status of a menu item.
WINDOW
Window to monitor the canister fill level. The canister is illuminated to make fill level monitoring easier. In the heating phase red LEDs are permanently on. Once the heating phase has been completed and the device is ready for use, blue LEDs light up.
CANISTER
Fluid canister with screw cap and intake hose. The sinter filter on the end of the intake hose ensures that contaminant particles do not get into the system and that the hose end is always at the lowest point of the canister. Completely disconnect the fog machine from the power supply (remove the power plug) before filling the canister. Let the fog machine cool down sufficiently to prevent burn injuries. Unscrew the lid of the canister and fill it with suitable fog fluid. Make sure that no fog fluid enters the device (take canister out of the fog machine). Put the intake hose back into the canister and carefully close it using the lid. Never operate the fog machine without fog fluid.
FOG OUTPUT NOZZLE
The fog output nozzle is located on the front side of the fog machine. Caution, very hot! When setting up and installing the fog machine, follow the information under “CAUTION! IMPORTANT INFORMATION ON FOG MACHINES!” in the safety instructions.
HANDLE SCREWS
Handle screws for adjustment of the mounting bracket.
VENTILATION SLOTS
Ventilation slots are located on the top of the device. Ensure that the ventilation slots are not covered and that air can circulate freely.
SECURING POINT
Securing point for attaching the device on crossbeam installations.

OPERATION

NOTES

Remove the protective film from the front of the fog machine before using it for the first time.
After connection to the power supply the fog machine’s heating phase will start (approx. 4 minutes). During this time the display will show “UP” and the fog output cannot be started. After the heating phase is completed the previously set DMX start address will be shown on the display when a DMX controller is connected to the device. In cable remote operation the green LED on the remote will light up. Operation by DMX controller has priority over operation by cable remote.
The fluid canister has a canister illumination to make fill level monitoring easier. In the heating phase red LEDs are permanently on. Once the heating phase has been completed and the device is ready for use, blue LEDs light up. Check the fill level regularly and refill with fog fluid as required (disconnect device from power supply before refilling).
Do not operate the fog machine without fog fluid! In order to remove fluid residue in the vaporizer system of your fog machine and thus ensure a long service life, clean the vaporizer system regularly (approx. every 60 operating hours). To do so, use the special Cameo cleaning fluid for fog machines and follow the instruction on the bottle label.

CONFIGURING DMX MODE
Press MODE to access the processing menu and press UP or DOWN until the display shows the menu item “Addr”. Confirm with ENTER then select the desired DMX start address by using the UP or DOWN buttons (hold down for fast value change) and confirm the selection by pressing ENTER.
SETTING DMX MODE
Press MODE to access the processing menu and press UP or DOWN until the display shows the menu item “chnd” (Channel Mode). Confirm with ENTER and then select the desired DMX operating mode by using the UP or DOWN buttons (1ch / 3ch). Confirm your selection with ENTER.

ACTIVATE / DEACTIVATE DARK MODE
In some situations the canister illumination and illuminated display can be disruptive. That’s why you have the option of activating dark mode, which deactivates canister illumination and the display. Press MODE to access the processing menu and press UP or DOWN until the display shows the menu item “dArK” (Dark Mode). Confirm with ENTER and use UP or DOWN to select “on” (activate dark mode) or “off” (deactivate dark mode). Confirm your selection with ENTER. When dark mode is activated the canister illumination will turn off immediately, the display after approx. 15 seconds. Press one of the control keys to reactivate the display.

OPERATION BY CABLE REMOTE

cameo-PHANTOM-F5-High-Power-Fog-Machine-11

Operation by cable remote is only possible if no active DMX controller is connected to the device. After connection of the cable remote to the appropriate REMOTE jack, the display will show the code that set last time. When the green LED display on the remote lights up the heating phase is completed and the fog machine is ready for operation.

MANUAL – press the button down for as long as you want the fog output to continue. The fluid pump will be operated at maximum output.
CONT – switch for continuous fog output. The fog quantity is preset using the VOLUME controller. The red display LED is lit up when this operating mode is activated.
TIMER – switch for time-controlled fog output. The fog quantity is preset using the VOLUME controller, the time interval is set using the INTERVAL controller and the fog output duration is set using the DURATION controller. The yellow display LED is lit up when this operating mode is activated.

The continuous fog output function CONT has priority over the time-controlled function TIMER. Manual control MANUAL has priority over both other functions.

SETUP AND INSTALLATION

Place the fog machine in a suitable location on its preinstalled rubber feet. Install on a crossbeam using an optionally available transverse clamp that is attached to the fog machine mounting bracket. Make sure that the device is firmly attached and secure it using a suitable safety cable on the provided point (A). The maximum permitted incline of the fog machine is 30°. During setup and installation, follow the information under “CAUTION! IMPORTANT INFORMATION ON FOG MACHINES!” in the safety instructions. Important safety information: Overhead installation requires extensive experience, including the calculation of workload limits and installed equipment, and periodic safety checks of all installation materials and devices. If you do not have these qualifications, do not attempt to carry out the installation yourself; contact a professional company. cameo-PHANTOM-F5-High-Power-Fog-
Machine-10

TECHNICAL SPECIFICATIONS

Product type: Fog machine
Type: Fog generator per vaporization principle
Heat-up time: Approx. 4 minutes
Heating element power: 1400 W
Output volume: Approx. 509 m³/min
Fog output range: Approx. 5-6 m
Output duration: Approx. 8-12 s
Reheating time: Approx. 15 s
Fluid consumption: Approx. 90 ml/min
Canister volume: 1.8 l
Controller: DMX512, cable remote with 10 m cable
DMX input: 3-pin XLR, male
DMX output: 3-pin XLR, female
DMX mode: 1-channel, 3-channel
DMX functions: Fog output, timer interval, timer duration
System settings: Dark mode on / off (display and canister illumination on / off)
Connection for cable remote: 5-pin DIN, female
Cable remote functions: Timer (interval, duration, volume), continuous fog output, manual fog output
Cable remote display elements: Fog machine ready for use (green LED), continuous fog output (red LED), timer function (yellow LED)
Display elements: 4-digit LED display
Power supply connection: Permanently connected power cable with CEE 7/7 power plug
Operating voltage: 230 V AC / 50 – 60 Hz
Fuse: F8AL 250 V (5×20 mm)
Power consumption: 1450 W
Ambient temperature (running): 5 °C – 40 °C
Relative humidity: < 85 %, non-condensing
Housing material: Metal
Housing color: Bi-color black / gray
Dimensions (W x H x D): 250 x 150 x 420 mm
Weight (without canister): 7.9 kg
Accessories (included): 4 rubber feet. Canister and cable remote included.

MANUFACTURER´S DECLARATIONS

MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY
You can find our current warranty conditions and limitations of liability at: https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERSDECLARATIONS_CAMEO.pdf. To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1, 61267 Neu Anspach / Email: Info@adamhall.com / +49 (0)6081 / 9419-0.

CORRECT DISPOSAL OF THIS PRODUCT
(valid in the European Union and other European countries with a differentiated waste collection system) This symbol on the product, or on its documents indicates that the device may not be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other waste and have it recycled to promote sustainable economic activity. Household users should contact either the retailer where they purchased this product, or their local government office, for details on where and how they can recycle this item in an environmentally friendly manner. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial waste for disposal.

FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation

CE Compliance
Adam Hall GmbH states that this product meets the following guidelines (where applicable): R&TTE (1999/5/EC) or RED (2014/53/EU) from June 2017
Low voltage directive (2014/35/EU)
EMV directive (2014/30/EU)
RoHS (2011/65/EU)
The complete declaration of conformity can be found at www.adamhall.com.
Furthermore, you may also direct your enquiry to info@adamhall.com.

DMX CONTROL

1-CH Mode

CH1| Output volume| 000| –| 005| No output
006| –| 255| 1 – 100 % output
3-CH Mode

CH1| Output volume| 000| –| 005| No output
006| –| 255| 1 – 100 % output
CH2| Timer interval| 000| –| 005| No interval (permanent on)
006| –| 255| 0,1 – 60 sec interval
CH3| Timer duration| 000| –| 255| 0,1 – 60 sec duration