WATTECO FlashO 50-70-071 LoRaWAN Counter Interface for Pulses User Guide
- June 10, 2024
- WATTECO
Table of Contents
FlashO 50-70-071 LoRaWAN Counter Interface for Pulses
Product Information
The Flash’O is an IoT device manufactured by WATTECO. It is a wireless optical sensor that provides readings of energy consumption through the measurement of light flashes from utility meters. The device has a LoRaWAN network connectivity and comes with three internal probes made of ASA/PC material with IP55 protection level. The device has a red LED for switching off and a green LED for association. It is available in two models, namely, 50-70-071 and 50-70-206 with different probe quantities and transmission power levels.
Product Usage Instructions:
To set up the Flash’O device, follow the instructions below:
- Unclip the optical sensor base and remove the protective film from the base without dirtying the double-sided tape.
- Position the hole in the base concentrically over the flash light to ensure good adhesion of the double-sided tape.
- Position the sensor on the baseplate and clip it by turning it on the baseplate until you hear a click sound.
- Check the radio coverage with Netw’O and make sure that the sensor is paired to the LoRaWAN network. For 60 seconds, the light flashes with each light flash from the meter.
To open or close the device, hold the device for more than one second or more than five seconds, respectively. When turning off the device, wait for a few seconds for the red LED to switch off. If the green LED flashes for three seconds, it indicates that the device is associating. Wait for this process to complete before proceeding with further actions. The device can be mounted on a wall or a RailDin installation. For more detailed instructions, visit the product’s support website at https://support.watteco.com/.
START
Provision the device on your LoRaWAN® network with the keys available on the secure platform.
POWER ON/ OFF
ON
OFF
Setting up of the box
Opening / Closure
Wall mounting
RailDIN
Please note that after installation of the railDIN kit, the protection rating of the housing will change to IP50
Installation Setting up
- cloth and isopropyl alcohol. Any other degreaser is strongly discouraged
- Unclip the optical sensor base. Remove the protective film from the base only. Do not dirty the double-sided tape.
- Position the hole in the base concentrically over the flash light.
- Press firmly on the base plate to ensure good adhesion of the double-sided tape.
- Position the sensor on the baseplate
- Clip the sensor onto the base plate by turning it. Pass the hard point. Click!
- First start-up / Checking the position of the optical sensor: The sensor must be paired to the LoRaWAN network. For 60 seconds the light flashes with each light flash from the meter
- Repeat with probes 2 and 3 (see page 2)
Radio propagation
Check the radio coverage with the Netw’O
Characteritics
| Référence / Reference | 50-70-071 | 50-70-206 |
|---|---|---|
| Classe / Class | A | A |
Niveau de puissance /
Power Level
| +14 dBm| +14 dBm
Sondes / Probes :| 1| 3
Antenne / Antenna| Interne
Internal
| Interne
Internal
Matériaux du boîtier /
Casing materials
| ASA/PC| ASA/PC
Indice de protection /
IP rating
| IP55| IP55
SITE SUPPORT
CERTIFICATIONS
Watteco represented by JC LE BLEIS, declares that the radio equipment type 50-70-071 / 50-70-206 is in conformity with Directive 2014/53/EU (RED) and UKCA. The full text of the EU and UKCA Declaration of Conformity is available at the following web address: https://www.watteco.com/assistance/download- center/
Thanks for choosing WATTECO devices
Documents / Resources
|
WATTECO FlashO 50-70-071 LoRaWAN Counter Interface for
Pulses
[pdf] User Guide
50-70-071, 50-70-206, 33-70-040-002, FlashO 50-70-071 LoRaWAN Counter
Interface for Pulses, FlashO 50-70-071, LoRaWAN Counter Interface for Pulses
---|---
References
- support.watteco.com/
- Concepteur et fabricant de capteurs transmetteurs radio connectés IoT - WATTECO
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>