RAIN HARVESTING TSEF27 Low Profile Tank Screen 360 Hood Kit w Screw Down Ring Installation Guide
- June 10, 2024
- Rain Harvesting
Table of Contents
RAIN HARVESTING TSEF27 Low Profile Tank Screen 360 Hood Kit w Screw Down
Ring Installation Guide
PRODUCT DETAILS
Maximum water throughout, easy debris management, simple maintenance, and minimal splashing. The Tank Screen 360 with the Hood is one of the best tank inlet solutions.
Effortlessly capture huge amounts of water in your tank – even as debris loads build on the screen.
The Low Profile design keeps any inbound pipes close to the top of your tank.
| Code | Size | Country |
|---|---|---|
| TSEF27 | 4OOmm | Global |
Installation
WHAT’S IN THE BOX?
- Low Profile Tank Screen 360
- Tank Screen 360 Hood
- Easy Fit Screw Down Inlet Ring
TOOLS/MATERIALS YOU MAY REQUIRE
- Drill
- Screws
HOW IT WORKS
The Tank Screen 360 is a high flow inlet solution for rainwater tanks. Its unique design keeps out sunlight, pests, and debris and offers simple maintenance.
INSTALLATION
- Secure your Inlet Ring by installing screws at 3 points around the perimeter. Make sure to use a screw that is appropriate for your tank material
- To secure your Low Profile Tank Screen 360, place it over the ring so that the 3 clips on the Tank Screen 360 align with the clips on the Inlet Ring. Push down firmly on each of the 3 clips until you hear them click into place. Ensure all 3 clips are secured.
- To install your Hood, secure it to the Tank Screen 360 by aligning the clips and pushing down firmly. Once again ensure that all 3 clips are secured
- Install your inlet pipes so that they sit in the opening between the Tank Screen 360 and the hood. The opening will allow for up to two 100mm pipes (Figure 1). Ensure the pipes are inserted into the unit fully to avoid splashing.
- To remove a Tank Screen 360 or Hood, lift each of the release tabs until they disengage, and the screen or hood can be lifted off.
Product Specifications
Low Profile Tank Screen 360 Hood Kit w/ Screw Down Ring
| COUNTRY | CODE | TANK HOLE SIZE | A | B | C | D |
|---|---|---|---|---|---|---|
| Global | TSEF27 | 348-382 | 420 | 165 | 100 | 346 |
| 13?’15.04” | 16.54″ | 6.5″ | 3.9″ | 13.62” |
All dimensions are in mm unless otherwise stated.
Maintenance
You should regularly inspect your Low Profile Tank Screen 360 and remove any leaves or debris. For a more thorough clean, simply unclip your Low Profile Tank Screen 360 and hose it off before reattaching to your tank.
A common misconception about collecting rainwater is that all you need is a roof, a tank and some rain. This ‘tanking’ approach cannot always be relied on to deliver the volume — or quality — of water that you require. That is where we can help.
With some thought, your rain harvesting system can provide you with cleaner water and lots of it. Whether you’re completely reliant on tank water or wanting to keep the garden green, our simple steps will help you achieve your goal.
The Rain Harvesting approach to rainwater collection involves using tested and proven products to make quality rainwater available for use in and around your property. You don‘t need much to get started and you will be surprised how easy it is to get the most out of your rainwater system.
How can we heIp_you?
DISCLAIMER This product specification is not a comolete guide to oroduct usage. Further information is available from Rain Harvesting Pty Ltd and *rom the Installation and Operating Instructions. This specification sheet must be read in conjunction with the Installation and Operating Instructions and all applicable statutory requirement. Product specifications may change without notice. Rain Harvesting Pty Ltd
For more information or to find out how we can help. just give us a call on
+61 7 3248 9600
Or visit our website at
rainharvesting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>