RAIN HARVESTING RHCL61 Leaf Eater Commercial w The Hood (PP) Installation Guide
- June 10, 2024
- Rain Harvesting
Table of Contents
RAIN HARVESTING RHCL61 Leaf Eater Commercial w The Hood (PP) Installation
Guide
PRODUCT DETAILS
Keep leaves and insects out of your rainwater system while capturing more rainwater by minimising splashing with The Hood.
Code | Size | Country |
---|---|---|
RHCL61 | J5Omm/6 | Glob |
Instaurations
WHAT’S IN THE BOX?
- Leaf Eater Commercial Body
- Leaf Eater Commercial Screen
- Leaf Eater Commercial Hood Screws
TOOLS/MATERIALS YOU MAY REQUIRE
- Tape measure
- Marker pen
- Saw
- Pipe Brackets
- Screws for mounting
- Screwdriver or drill
INSTALLATION
- Locate the position at which you will be installing your Leaf Eater Commercial with The Hood. Whether this is directly under your eave or midway down your downpipe, it should be a minimum of 500mm above your tank inlet and tank overflow pipe.
- Cut and bracket your bottom downpipe to the wall, being sure to offset it 3Omm from the wall, if it isn’t already offset.
- Insert your Leaf Eater Commercial with The Hood into the pipe and mark the top and bottom flange fastening holes. Remove your rain head and prepare the necessary fastening points. Then reinsert your rain head and fasten it to the wall, ensuring it‘s adequately supported by the wall structure.
- Cut your upper pipe so that it will sit at least 20mm below the top of the hood when installed.
- Slide The Hood cover up the top section of pipe and lower the bottom skirt into the corresponding channel on the screen.
HOW IT WORKS
Product Specifications
Leaf Eater Commer cial with The Hood (PP)
Country | Code | A | B | D | E | F | G | H | |
---|---|---|---|---|---|---|---|---|---|
Global | RHCL61 | 164mm (For attaching a flexible coupling) | 149 mm (Fits inside | ||||||
ISO DWV, 6″ SCH4O,& 6″ SDR35) | 1A0mm (Fitsinside 150 Pressure Pipe) | ||||||||
369mm(14.5″) | 367mm(14.4“) | 488mm(19.2′ |
528mm(20.8“)
|
568mm(22.4″)
AI! dimensions are in mm unless otherwise stated.
Fitting guide:
F = Female / Socket Fitting
M = Male / Spipot Fitting (Pipe size)
IP = In-Pipe Fitting
Maintenance
- Slide The Hood cover up your inlet pipe and undo the screws to remove The Hood screen.
- With the screen removed, either brush off or wash the debris from the screen.
- Reinsert the screen into the Leaf Eater Commercial body, making sure it is fully seated all the way around and flush with the body. Secure the screen to the body using the screws.
- Reinstall the cover, making sure that the skirt around the edge is fully seated in the corresponding channel on the screen
A common misconception about collecting rainwater is that all you need is a roof, a tank and some rain. This ’tanking’ approach cannot always be relied on to deliver the volume — or quality — of water that you require. That is where we can help.
With some thought, your rain harvesting system can provide you with cleaner water and lots of it. Whether you’re completely reliant on tank water or wanting to keep the garden green, our simple steps will help you achieve your goal.
The Rain Harvesting approach to rainwater collection involves usinp tested and proven products to make quality rainwater available for use in and around your property. You don’t need much to get started and you will be surprised how easy it is to get the most out of your rainwater system.
How can we heIp_you?
DISCLAIMER This product specification is not a comolete guide to oroduct usage. unher information is available rom Rain Harvesting Pty Ltd and from the installation and Ooerating instructions. This specification sheet must be read in conjunction with the installation and Operating Instructions and all applicable statutory requirement. Product specifications may change without notice. Oc Rain Harvesting Pty Ltd
RAIN HARVESTING
by Blue Mountoin Co
For more information or to find out
Or visit our website at
+61 7 3248 9600
RAIN HARVESTING
by Blue Mountoin Co
how we can help, just give us a call on
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>