Simply Retrofits Canopy Parking LED Light Installation Guide

June 10, 2024
Simply Retrofits

Simply Retrofits Canopy Parking LED Light Installation Guide
Simply Retrofits Canopy Parking LED Light

Installation Instruction

Cautions:

  1. Can not use the electric generator to test the LED lamp.
  2. Please abide by related country, regional and local law and regulations when install this fixture.
  3. Please turn off the power before installation or maintenance.
  4. Proper earth grounding is required to ensure safety.

Notice:

  1. To avoid possibility of electrical shock or fire, the installation personnel must have professional electric knowledge.
  2. Please wear gloves to avoid injury before installation.
  3. If any smoke or spark of the wire happened, please turn off the power immediately and notify relevant personnel.

Special functions instruction:

  1. Photocell and CCT adjustment integrated controller CCT adjustment 1. The color temperature of the lamp turns to 3000K when the DIP switch is set to 3K.
  2. The color temperature of the lamp turns to 4000K when the DIP switch is set to 4K.
  3. The color temperature of the lamp turns to 5000K when the DIP switch is set to 5K.

Photocell function

  1. Turn the DIP switch to ON means the photocell is turned on.
  2. Turn the DIP switch to OFF means the photocell is turned off .
    ADJUSTMENT

Wattage adjustable
Turn the DIP switch to different position, the power of the lamp will change to the corresponding wattage.
ADJUSTMENT

Color temperature adjustable

  1. The color temperature of the lamp turns to 3000K when the DIP switch is set to 3K.
  2. The color temperature of the lamp turns to 4000K when the DIP switch is set to 4K.
  3. The color temperature of the lamp turns to 5000K when the DIP switch is set to 5K.
    ADJUSTMENT

Photocell sensor
sensor

Wattage adjustable
Wattage adjustable

Microwave sensor
Microwave sensor

Attention:

  1. Please check if there is any damage during shipping. If so, please contact manufacturer timely.
  2. Please read the installation instruction carefully to check whether all the accessories are complete. After confirmation, then install the fixture according to installation steps.

Wiring Diagram:
Wiring daigram

  1. Recommended dimmer: Brand: LUTRON, model: NTSTV-DV; Brand: LEVITON, model: DS710-10Z; Brand: LEVITON, model: IP710; Brand: Legrand, model: RH4FBL3PW;
  2. If other dimmers are used, they must be passive dimmers, and the turn-off voltage should be between 0.6V-0.65V;
  3. Please use the dimming+, dimming- (DC 10V) marking leads to connect to outside dimmer, Class T Wiring Only. Please assure a cumulative leakage current of less than 3.5mA on the control circuit.

Installation Method I :

  1. Connect the wring to the local power supply in the 3/4″NPT Stem (Figure 1).
    INSTALLATION

  2. Screw the fixture to the 3/4″NPT Stem(Figure 2).

Installation Method :

  1. Take off the plate of the led fixture

INSTALLATION

  1. Drill the holes on the ceiling accordingly to fit the plate (Figure 4).
    (Figure 3).
    INSTALLATION

  2. Drill the rubber plug into the ceiling, then fix the plate to the ceiling. (Figure 5).

  3. Hang the fixture by the plate (figure 6), then connect to local power supply with necessary wiring protection .
    INSTALLATION

  4. Install the fixture by the plate, then fasten the screws on both sides of the fixture (Figure 7) .
    INSTALLATION

Wiring diagram

  1. Photocell and CCT adjustment integrated controller ,Wattage adjustable switch and Microwave sensor(The maximum power of the lamp is subject to the setting of the wattage adjustable controller. When the setting power is lower than the stand-by dimming level of the motion sensor, the stand-by dimming level is subject to the setting of the wattage adjustable controller.)
    WIRING DIAGRAM

  2. Color temperature adjustable switch,Photocell sensor,and Microwave sensor
    WIRING DIAGRAM

  3. Wattage adjustable switch,Color temperature adjustable switch,and Microwave sensor(The maximum power of the lamp is subject to the setting of the wattage adjustable controller. When the setting power is lower than the stand-by dimming level of the motion sensor, the stand-by dimming level is subject to the setting of the wattage adjustable controller.)
    WIRING DIAGRAM

Warning /Avertissement

MIN 75°C SUPPLY CONDUCTORS THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

LES FILS D’ALIMENTATION 75°C MIN CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHERENTS.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Simply Retrofits User Manuals

Related Manuals