GERMAN GP13 Series Built In Gas Cooking Range User Manual

: June 9, 2024
: German

Table of Contents

GERMAN GP13 Series Built In Gas Cooking Range
WARNINGS & SAFETY PRECAUTIONS
PRODUCT STRUCTURE
INSTALLATION INSTRUCTIONS
OPERATION INSTRUCTIONS
CLEANING & MAINTENANCE
TROUBLESHOOTING
TECHNICAL SPECIFICATION
Warranty Terms & Conditions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GERMAN GP13 Series Built In Gas Cooking Range

GERMAN-GP13-Series-Built-In-Gas-Cooking-Range-product

WARNINGS & SAFETY PRECAUTIONS

WARNING!

Read all instructions carefully before using this product.
This product is not intended for use by children or persons with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of this product by a person responsible for their safety.
Mind your children and DO NOT let children play with this product.
Cleaning and user maintenance shall not be made by children without supervision.
Check the “Gas type”, “Gas working pressure”, “Rated heat input” indicated on the rating label before using this product.
This product is for domestic indoor use only.
If the gas connection piping is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazards.
Make sure the ignition knob is at “●” position and the gas cooker has completely cooled down before cleaning and maintenance.
Contact German Pool authorized service technician for repair or maintenance of this product.

Notice Before Use
Important
For safety purposes, you should read the instructions carefully before using the appliance for the first time. Save the instructions for future reference.
The appliance is designed for domestic use and may only be installed and operated in accordance with these instructions for use.

The cooking range must be installed by registered gas installers.
Ensure that the cooking range is used with good ventilation. Environment with insufficient oxygen should be avoided.
This built-in range is to be used for cooking only. DO NOT dry towels, clothes etc. over it.
During long period of use, open window or exhaust fan to ensure good ventilation.
Check that all control knobs have been set to “●” position after use.
If the flame is blown out during use, the safety valve will cut off gas supply. Ignite again after at least 1 minute.
Take extra care when cooking oil or fat. High temperature of oil or fat may cause fire hazard.
To avoid hazard, DO NOT use spray or compressed gas when the cooking range is in use.
After ignition, check if the flame is even and normal. Before removing cookware away from the flame, always set to small flame or “●” position.
To avoid damage to the cooking range, DO NOT place any hot mat between the range rack and the utensil.
DO NOT use burner rack other than the one provided. Otherwise, it will cause overheat to the range surface.
DO NOT use over-size or over-weight utensils. Or it will cause excessive heat to be reflected back onto the range surface.
Place the utensil steadily on the range rack. DO NOT tilt the utensil.
Contact German Pool Customer Service and Repair Centre for repair and parts replacement. During guarantee period, German Pool resrves the right to charge for spare parts and service fees if the damage is caused by misuse or improper installation.
When installing built-in gas hob on top of stove cabinet, please check that there is provision for ventilation at the cabinet to ensure proper operation of the gas hob.
DO NOT store any flammable materials, sprays or pressurised containers inside the stove cabinet.
The panel of this built-in hob is made of tempered glass which is safer than normal glass for this application. However, the following safety precautions for using built-in hob with glass top panel should also be noted in order to prevent the glass top panel from breaking:
Clean the burner assembly frequently to maintain a clear gas passage on the flame distributor.
Clean and tidy up the flame distributor after spillage of food and liquid once the burner assembly cooled down.
Turn off the gas appliance immediately if abnormal noise propagates from the gas appliance and contact gas supply company or gas hob importer for inspection.
DO NOT use oversized utensils for cooking, utensil size should be less than 34cm.
DO NOT impact the glass surface with hard objects or place heavy objects on the glass surface.
Maximum load weight for this gas hob is 10kg.

PRODUCT STRUCTURE

GERMAN-GP13-Series-Built-In-Gas-Cooking-Range-fig
2 GERMAN-GP13-Series-Built-In-
Gas-Cooking-Range-fig 4 GERMAN-GP13
-Series-Built-In-Gas-Cooking-Range-fig 5

INSTALLATION INSTRUCTIONS

WARNING!
The gas cooking range must be installed by registered gas installers (RGI). Otherwise, German Pool will not be held responsible for any damages.

Attention:

The use of a gas-cooking appliance produces heat and moisture. Please ensure that the kitchen is well ventilated. It is recommended to keep natural ventilation windows open or install a mechanical ventilation device (exhaust fan or range hood). For prolonged intensive use of the appliance, additional ventilation is required, for example opening windows or doors, or increasing the level of mechanical ventilation where present.
Install the built-in hob in a well ventilated room and keep it away from any combustible or inflammable objects such as paper or oil.
Place the built-in hob on a stable and level surface.
If the unit is to be installed close to combustible surroundings (such as wooden walls, wooden shelves), it should be installed at least 15 cm (6”) from the side walls. The unit should be installed with a distance of at least 15 cm away from surrounding combustible materials.
Leave at least 25 mm (1”) gap between the underside of the cooking range and the countertop/cabinet shelf board below.
External gas governor is not required.

Room Ventilation
The kitchen should have no less than 20m³ air volume for regular gas combustion and be kept well ventilated at all time. Air must be able to naturally flow through the permanent opening in the walls (eg. windows and doors) of the room.
These openings must be able to vent the fumes outdoors and their openings must be at least 100cm², and ensure that they should never be blocked. Indirect ventilation by air drawn from an adjacent room is also permitted, in strict compliance with any local regulation in force.
Gas Ventilation
Attention:
According to the Gas Safety Regulations of Hong Kong, any gas installation works including the installation of appliances and connection tubing, must be undertaken by registered gas installers (RGI) who are registered for that appropriate classes and be employed by registered gas contractors. Before connecting the appliance, check that the specifications on the data label affixed to the underside of the hob correspond to those of the gas and electricity mains in the house. A label on the appliance indicates the regulating conditions: Type of gas and working pressure. Gas connection must comply with the pertinent standards and provisions in force. The size of the gas inlet is ½ inch.

A. LPG Connection
- Tubing Connection: please use copper piping or approved rubber tubing bearing EMSD approval marking (eg. EMSD APPROVAL GTXXXX), accessories and gas cock for connecting from ½ inch B.S.P. thread at back of the unit to the gas supply point.
- Stainless steel braided flexible hose connection: please use approved stainless steel braided flexible tubing bearing EMSD approval marking (eg. EMSD APPROVAL GTXXXX), accessories and gas cock for connecting from ½ inch B.S.P. thread at back of the unit to the gas supply point.
B. Town Gas Connection
Please use approved stainless steel braided flexible tubing bearing EMSD approval marking (eg. EMSD APPROVAL GTXXXX) and gas cock for connecting from ½ inch B.S.P. thread at back of the unit to the gas supply point.

Cut-out Dimensions

Model No.	W（mm）	D（mm）	R（mm）

GP13-3-TG

GP13-3-LG

| 815| 405| 50
GP13-2-TG

GP13-2-LG

| 665| 345| 50
GP13-2M-TG

GP13-2M-LG

| 463| 342| /
GP13-1-TG

GP13-1-LG

| 265| 490| /

Correct Position of Burner Rack & Burner Cap
Make sure that the following parts are fitted properly before use.

Burner Rack
Fit burner rack onto Drip Pan (Fig. 1). DO NOT tilt the placement, otherwise it will cause the fire to be abnormal.
Burner Head
Install the Burner Cap and Burner Ring onto Burner Head Base (Fig.2), DO NOT tilt or leave a gap during installation (Fig.3). If either is incorrectly placed, using the cooking range may cause the burner head to deform, or the glass may break, or increase the risk of releasing carbon monoxide (CO ).

OPERATION INSTRUCTIONS

WARNING!
All cooking ranges must be installed, tuned and connected by registered gas installers. DO NOT install or repair the cooking range yourself.
DO NOT use additional fitting, such as aluminium foil.
DO NOT clean the top of the sensor with a hard brush or sharp object, as they may damage the sensor.

While pushing the control knob, turn it to the left (towards the “ ” position) slowly until you hear a ‘clicking’ sound. Electronic spark will ignite burners. Release your hand after confirming the burners are ignited. The hob has automatic continuous ignition function, DO NOT continue pushing the control knob after ignition. ‘Click’ sound and spark will stop automatically after 6-8 seconds.
If the flame goes out when you release your hand, repeat the ignition procedure again but try releasing your hand slowly.
Turn Control Knob to adjust flame to desirable setting.
Turn the Control Knob slowly to adjust the flame intensity between “●” and “ ”. (Fig.4).
If the flame extinguishes during use, the safety device will automatically shut off the gas supply. When this happens, turn the Ignition Control Knob knob to “●” position.
Turning the knob backwards to the “●” position will extinguish the burner.(Fig.5)

Flame Failure Safety Device

If the flame extinguishes during use, the automatic flame failure safety device will shut off gas supply to the cooking range. When this happens, turn the knob to “●” position.
The safety sensor is very delicate –DO NOT use hard brushes or rough cleaning pads when cleaning it.
Aeration is preset at factory. DO NOT attempt to adjust it.

CLEANING & MAINTENANCE

WARNING!
DO NOT clean the unit when it is hot. Wait until the cooker range has completely cooled down before cleaning.

Cleaning The Cooker Range

Wipe the glass panel with a soft damp cloth and mild detergent.
Wash the burner racks and burner heads with warm water and detergent.

Changing The Battery

Battery Box is located on the underside of the product. Open the door of battery box and change the battery (DC1.5V x 1).
Ensure polarity connection (“+” and “ -”) of the battery is correct.

TROUBLESHOOTING

Problem	Possible cause	Solution

No ignition

| Gas valve not open or gas is used up| Open gas valve or change gas supply
Air in the gas tubing| Prolong ignition time and repeatedly ignite till air is vented out
Gas hose is bent| Straighten gas hose
Injector is clogged| Contact Customer Service & Repair Centre or

registered gas installer (RGI) to clear blockage

Ignition plug has soot or is in wrong position| Contact Customer Service & Repair Centre or RGI to clear or adjust the plug
Flame holes of burner cap are

blocked by water or filth

| Clean and dry burner cap

Gas smell

| Gas tubing has aged| Contact Customer Service & Repair Centre or RGI to change a new gas tubing
Main fire of burner not lighted| Re-ignite after the gas has dispersed
Valve leak| Contact Customer Service & Repair Centre or RGI to change a new valve

Weak flame

| Gas pressure too low| Contact Customer Service & Repair Centre or RGI to check gas supply or whether gas regulator is clogged
Ports of burner cap are clogged| Clean ports
Air hole is not properly adjusted| Contact Customer Service & Repair Centre or RGI

to re-adjust air hole for proper air flow

WARNING! If the cooking range still fails to ignite after following the above suggested solutions, DO

NOT attempt to ignite by other means. Please contact German Pool Customer Service & Repair Centre.

TECHNICAL SPECIFICATION

Model	GP13-3-TG	GP13-3-LG
Gas Type	H.K. Towngas	H.K. LP Gas
Gas Working Pressure	1500 Pa	2900 Pa
Rated Heat Input	(L) 6.0kW / (M) 1.6kW / (R) 6.0kW	(L) 5.0kW / (M) 1.6kW /

(R) 5.0kW
Voltage| DC 1.5V x 1
Ignition Method| Impulse Ignition System
Safety Device| Yes
Product Dimensions (mm)| 125(H) x 860(W) x 450(D)
Weight| 18 kg
Model| GP13-2-TG| GP13-2-LG
---|---|---
Gas Type| H.K. Towngas| H.K. LP Gas
Gas Working Pressure| 1500 Pa| 2900 Pa
Rated Heat Input| (L) 6.0kW / (R) 6.0kW| (L) 5.0kW / (R) 5.0kW
Voltage| DC 1.5V x 1
Ignition Method| Impulse Ignition System
Safety Device| Yes
Product Dimensions (mm)| 125(H) x 750(W) x 450(D)
Weight| 15 kg
Model| GP13-2M-TG| GP13-2M-LG
---|---|---
Gas Type| H.K. Towngas| H.K. LP Gas
Gas Working Pressure| 1500 Pa| 2900 Pa
Rated Heat Input| (L) 6.0kW / (R) 1.6kW| (L) 5.0kW / (R) 1.6kW
Voltage| DC 1.5V x 1
Ignition Method| Impulse Ignition System
Safety Device| Yes
Product Dimensions (mm)| 125(H) x 580(W) x 380(D)
Weight| 10.8 kg
Model| GP13-1-TG| GP13-1-LG
---|---|---
Gas Type| H.K. Towngas| H.K. LP Gas
Gas Working Pressure| 1500 Pa| 2900 Pa
Rated Heat Input| 6.0kW| 5.0kW
Voltage| DC 1.5V x 1
Ignition Method| Impulse Ignition System
Safety Device| Yes
Product Dimensions (mm)| 130(H) x 315(W) x 515(D)
Weight| 7.8 kg

Warranty Terms & Conditions

Under normal operations, the product will gurantee a 1-year full warranty provided by German Pool (effective from the date of purchase).

This warranty is not valid until customer registration information is received by our Service Centre within 10 days of purchase via one of the following means:

Visit our website and register online: www.germanpool.com/warranty
Complete all the fields on the attached Warranty Card and mail it back to our Customer Service Centre.

Model No. :
Serial No. :
Purchased From :
Invoice No. :
Purchase Date :

Customer who fails to present original purchase invoice will not be eligible for free warranty service.
Customer should always follow the operating instructions. This warranty does not apply to:
- labour costs for on-site installation, check-up, repair, replacement of parts and other transportation costs;
- damages caused by accidents of any kind (including material transfer and others);
- operating failures resulting from applying incorrect voltage, improper usage, and unauthorized installations or repairs.
This warranty is invalid if:
- the purchase invoice is modified by an unauthorized party;
- the product is used for any commercial or industrial purposes;
- the product is repaired or modified by unauthorized personnel, or unauthorized parts are installed;
- the serial number is modified, damaged or removed from the product.
German Pool will, at its discretion, repair or replace any defective part.
This warranty will be void if there is any transfer of ownership from the original purchaser.