FLASH F7300253 Logo 200W IP65 Projector User Manual

: June 9, 2024
: FLASH

Table of Contents

INTRODUCTION
SAFETY INFORMATION
PRODUCT INFORMATION
INSTALLATION
CONNECTION
DMX CHANNELS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FLASH F7300253 Logo 200W IP65 Projector

INTRODUCTION

THANK YOU FOR PURCHASING Logo 200W IP65. FOR SAFETY REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

WARNING!

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking its headonly, but always by taking its base.
Maximum ambient temperature is: +350C Don’t operate it where the temperature is higher than this.
In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light spot while the fixture is on.

WARNING!

WARNING! The Logo 200W IP65 has a powerful pan motor. The torque reaction when the head is panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do not apply power to the Logo 200W IP65 unless the baase is securely fastened to a surface or to rigging hardware.
WARNING! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 900 clockwise.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
WARNING! Position or shade the head so that the front lens will not be exposed to sunlight or any other strong light source from any angle – even for a few seconds. See Figure 2. The Logo 200W IP65 lens can focused the sun’s rays, creating a potential fire hazard and causing damage.
IMPORTANT! Do not point strong light output from other fixtures at the Logo 200W IP65, as intense illumination can damaged the display.

PRODUCT INFORMATION

Light Source: 1 pc LED 230W White
LED life: 50000 hours
Color Temperature: 6500-7000K
Angle: 10,20,30,45, 60 Optional
Light Spot: Circle/Splice Square
Dimmer: 0-100% linear dimmer.
Cooling system:Fan wind cooling
Display: LCD display
Focus: Manual
Electronic positioning function
Light source overheat protection and intelligent offline control mode
Smart off-line auto run mode. preprogram the effects in the fixture and when it is power ON, it will play automatically
Focus: Manual Focusing
Temperature: Light Source’s temperature is monitored real time
Angle adjust: Up/Down – 180°
Inner electronics with moisture-proof protection
Working environment: -25 to +35
Running Mode: Manual. Auto. Master/Slave
Protection IP65
Net Weight: 11 kg + (Case 14,2 kg)
Dimensions: H(34 )xW(30)xD(36) cm
Interchangeable Gobos: 37.3 mm diameter

INSTALLATION

fle unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

CONNECTION

The device is equipped with the following interfaces:

DMX (in/out): XLR 3-pin socket
Power (in/out): power CON socket

Connecting DMX signal

The connection is performed using cable with XLR-female -> XLR-Male plugs.

CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and signal (+) into a XLR plug and plug it in the DMX output of the last fixture.

Voltage specification

Input Voltage	Total Power	Frequency
110-240V	250W	50/60Hz

Connecting power supply

The connection is performed using power cable with PowerCon connector ( i n c l u d e d ) . T h e d e v i c e m u s t b e operated by qualified personnel Make sure that the power grid supply parameters are consistent with device parameters and limitations are not exceeded.

CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions.

Make sure that the power grid supply parameters are consistent with device parameters and limitations are not exceeded.
**** Using lamp, the change rate of power voltage should be within ± 10%, if the voltage is too high, it will shorten the light’s life; if it’s not enough, the lamp will be dark. Please restart it after turning off light for 20 minutes until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.

Menu Structure:

DMX CHANNELS

Setting	Mode	DMX
DMX address	001-512	enter to edit, up or down change, enter to save
Channels	5CH	Channels
No DMX	Keep	old state to continue



Screen Protection	Off	Backlight shut off
Overheat protection	085	0-99 range, exceed temperature, power reduce,