CRUX SWRTY-61P Interface for Select Toyota Models with JBL Instruction Manual
- June 4, 2024
- CRUX
Table of Contents
SWRTY-61P Interface for Select Toyota Models with JBL
Instruction Manual
Radio Replacement Interface with Steering Wheel Control and BL Amplifier Retention for Select Toyota Vehicles 2018-Up
PRODUCT FEATURES:
- Retains factory features in select Toyota vehicles while functioning with an aftermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- Retains the factory JBL amplifier.
- Retains factory backup camera and sensors.
- Retains factory bird’s eye view feature (if equipped).
- Retains factory Auxiliary Audio Input.
- Includes factory USB retention adapter cable.
- Includes antenna adapter.
PARTS INCLUDED:
INSTALLATION DIAGRAM:
INSTALLATION INSTRUCTIONS:
1. Connect the SWRTY-61P T-harness to the aftermarket radio harness. Refer to the diagram on page 1 for wire color codes.|
---|---
2. Remove the padded trim above the glove compartment.
| |
3. Carefully pull out the trim under the radio.| 4. Remove the small trim
next to the shifter.| 5. Remove the AC control panel below the radio.
| |
6. Unplug the connector behind the AC control panel.| 7. Pull out the radio
and unplug the connectors.| 8. Mate the factory radio connectors to the
SWRTY-61P T-harness. Test for functionality then install the aftermarket
radio.
Factory bird’s eye view and proximity sensors feature is retained.
The image on the left is from a 2019 Toyota Camry using a Sony radio.
DIP SWITCH SETTINGS:
AFTERMARKET RADIO DIP SWITCH SETTINGS:
| RADIO BRAND: | DIP: | 1 | 2 | 3 | 4 |
|---|
Atoto, Dual, Farenheit, Jensen, Pioneer
Power Acoustik, Soundstream
Blaupunkt, Most o -brand Radios
Alpine
Clarion
Kenwood
JVC
Boss, Old Sony
New Sony| | OFF| OFF| ON| ON
| OFF| OFF| ON| ON
| OFF| OFF| ON| ON
| OFF| OFF| OFF| OFF
| OFF| ON| ON| OFF
| OFF| ON| ON| ON
| OFF| ON| OFF| ON
| OFF| ON| OFF| OFF
| OFF| OFF| OFF| OFF
NOTE: For Auto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most off-brand radios, check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
TOYOTA STEERING WHEEL CONTROL DIP SWITCH SETTING:
| DIP: | 5 | 6 | 7 | 8 |
|---|---|---|---|---|
| Toyota | OFF | ON | OFF | ON |
3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.
NOTE: Insulate the Blue/Yellow wire or 3.5mm plug if not being used.
For aftermarket radios that have wires for SWC connections, cut off the 3.5mm plug on the Crux SWC Cable and connect the SWC wires per the diagram on the right:
Note that there are sthe ome radios that only have SWC1 and SWC2, in this case, “shield” does not need to be connected.
VEHICLE APPLICATIONS:
Toyota
| 2020-Up | 4Runner |
|---|---|
| 2019-Up | Avalon |
| 2018-Up | Camry |
| 2019-Up | CH-R |
| 2018-Up | Corolla |
| 2020-Up | Highlander |
| 2019-Up | RAV4 |
| 2020-Up | Sequoia |
| 2018-Up | Sienna |
| 2020-Up | Tacoma |
| 2020-Up | Tundra |
NOTE: For JBL amplified vehicles ONLY.
http://www.cruxinterfacing.com
Crux Interfacing Solutions • Chatsworth, CA 91311
phone:818-609-9299 •
fax: 818-996-8188 •
www.cruxinterfacing.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>