ALVIS AC7000-AE-25 Smart Home Series Wallbox AC Charging Station User Manual

ALVIS AC7000-AE-25 Smart Home Series Wallbox AC Charging Station User Manual

Safety and Warning

Save these instructions. Read all instruction before installing or using the charger.

1. Keep the charger away from explosive or flammable materials, chemicals, vapors and other hazard objects.
2. Keep the charger socket clean and dry. If it gets dirty, please wipe it with clean dry cloth.
3. Touching the socket core is strictly forbidden when power on.
4. Do not use the charger in case of any device defects, crack, abrasion, bare leakage and so on. Please contact the professional personnel if any of these conditions occurs.
5. Do not attempt to dissemble, repair, refit the charger. If necessary, please contact the professional personnel. Improper operation will result in device damage, electric leakage, etc.
6. In case any abnormal condition happens, please cut off all input and output power supplies immediately.
7. Please protect charging carefully from rain and lightning.
8. Keep children away from the charger.
9. During charging, do not drive the EV. Charge only when the EV is stationary. For hybrid cars, charge only when the engine is switched off.
10. Our packaging materials are environmentally friendly and can be recycled. Please put the packaging in applicable containers to recycle it. Do not dispose of this device with the household waste. It should be taken to a suitable facility for recycling of electrical and electronic devices. For more detailed information about recycling of this device, please contact your local city/town council office or your household waste disposal service.

Warning

The input and output voltages of this device are high voltage, which threaten human life safety. Please strictly observe all warnings on the device and user manual. Unauthorized and non-professional service personnel are forbidden to remove the cover of this device.

Introduction

Product Technical Specifications

protection, Surge protection, Over/Under voltage protection, Over/Under frequency protection, Over temperatureprotection
Certification| IEC 61851-1: 2017, IEC 61851-21-2: 2018
Warranty| 2 years
Environment| Installation| Wall-mount/Floor-mount
Working Temperature| – 30℃~+50℃
Working Humidity| 5%~95%
Work Altitude| <2000m
Package| Product Dimension| 328.07180.7386.84 mm (HWD)| 328.07180.7386.84mm (HWD)
Package Dimension| 415255190 mm (LWH)| 415255190mm (LWH)
Net Weight| 2.8kg| 3.2kg
Gross Weight| 3.3kg| 3.8kg

External Structure

Package Contents

Unpack the product. Please check and verify following items after receiving the charger:

• Visual inspection on charger’s external appearance. If there is any breakage or other damage, please notify the seller immediately.
• Check type and quantity of all accessories as follows. If there is a shortage in the quantity of any item or if any items are missing, please contact the seller at once.

| | |
---|---|---|---
Wallbox (x1)| φ6 Expansion Pipe(x6)| Self-tapping Screw (x6)| Installation Position Template (x1)
| | |
User Manual (x1)| M4 Wrench (x1)| Insulated Terminal for Single-phase(x3) for Three-phase(x5)| Cable Holder (x1)

Operation Instruction

Installation Preparation

Tools required

Cables & Materials

actual requirement
Insulated tape| 0.15mm*18mm, 0~600V,0℃~80℃| Depend on actual requirement
Connector for mains cable| RJ45| Depend on actual requirement
Insulating tape| 0.15 mm × 18mm; 0-600V;0°C-80°C| Depend on actual requirement
Cable tie| 4 × 200mm| Depend on actual requirement

Installation Process

1. Installation Notice
   • Electrical devices should only be installed, operated, and maintained by qualified personnel. No responsibility is assumed by the manufacturer for any consequences arising out of the use of this device. A qualified person is one who has certified skills and knowledge related to the construction, installation and operation of this type of electrical device and who has received safety training to recognize and avoid the hazards involved.
   • All applicable local, regional, and national regulations must be applied when installing, repairing and maintaining this device.
   • RCD of the charger is integrated 6mA DC, please install a Type A or Type B breaker outside.
2. Checks before starting the Installation Process
   • Ensure the charger’s location allows good operational access for normal use and repair & maintenance.
   • The AC input components within the premise’s power supply are correctly fitted with required protection items prior to installation of the charger.
3. Installation Procedure
   • Based on the installation position template, identify the installation position and mark the two holes for the wall screws, which will be inserted in the top rear of the charger.
   • Drill two holes with the 6mm diameter drill bit and insert the plugs horizontally into the holes, paying attention to the force and depth with which they are inserted (make sure the plug completely enters the hole).
   • Insert the two M4x32 screws into the wall plugs, allowing the heads of the screws to protrude by at least 5 mm.

• Provisionally position the charger by inserting the head of the screws into the upper holes at the rear.
• Open the front of the charger.
• Mark the position of the third fastening screw. The hole is located at the bottom of the charger.
• Remove the station and make the third hole, inserting the wall plug.
• Reposition the station and secure the third screw at the bottom.
  

Electrical Connection

Charger Appearance

Overview of Internal Structure

AC Wiring

Note: Before insert input power wire, please cut silicon sealed loop as required to maintain IP65.

1. Remove a length of 40mm of the cable jacket and strip the wire insulation to a length of 8~15mm.

2. Crimp the terminals as shown in the figure below.
   Single-phase Wiring
   
   Three-phase Wiring
   

3. Distinguish different input wires of three-phase and single-phase, then insert the wire into the corresponding wire slot.
   Single-phase Connection

Three-phase Connection

Note: If your charger is with PEN protection function, please connect the wires as follow.

Configuration and Operation

Power-on Checking

1. Checks before Power-on
   Please check/re-check the following items prior to initial Power-on:

   • The charger’s location allows good operational access tonormal use and repair & maintenance.
   • The AC input components within the premise’s power supply are fitted correctly with required protection items prior to installation of the charger.
   • Reconfirmthe charger is installed properly.
   • No componentsor other items have been left onthetop of thecharger.

2. LED status
   When powering on the charge point, the LED indicator should be in standby status.

green slowly,1second on; 3 seconds off;
Ready to charge| The charging connector is plugged in successfully| Flashing green fast, 200ms on; 1s off; 5 times;3s off;
Charging| Charging in progress| Breathing green, 1s on; 1s off
Fully charged| The electric vehicle is fully charged| Solid green
Unplug| The charging connector is unplugged| Return to standby mode
RFID card read| Put the RFID card on thereader and it is successfully read| Flashing yellow fast;100ms on; 100ms off; 5 times

Evchargo App

The Evchargo App is intended for everyday charging. In Evchargo, except the basic operating functions, you can also configure both network and the charger. Scan the QR code below to download and use the app.

Download Evchargo

Instructions for Evchargo

Configuring the charger
There are two ways to configure the charger. One way is by Evchargo app, another way is by AP (access point) mode.
For user, it is recommended to use Evchargo app to configure the network and the charger. AP mode is recommended to be used by the professionals or under the guidance of the professionals.

• By Evchargo App
  Please download Evchargo app (QR code as shown above), and follow the app user manual to configure the network and the charger.

• By AP (access point) mode
  The AP mode is used for the local network configuration of the charger, and a mobile device is required to connect your mobile device to the hotspot of the charge. You can initiate the hotspot interface by following the instructions below:

Preparation

1. Activate the hotspot

   • Activate the hotspot of the charger by restarting the power.
   • The hotspot of the charger remains available for 15mins since charger reboot.

2. Connect to Charger Hotspot

   • Turn on the smartphone Wi-Fi, and connect the hotspot of the charger. If unable to connect, try using Airplane mode.
   • The name of the hotspot Wi-Fi starts with the charger SN number, i.e. ”SN…” .
   • The password is “admin123’’.

Login

• Open the browser on your smartphone and enter 192.168.4.1 in the address bar.
• Log in using the four-digit PIN code located on the last page of the manual. After login, the function menu will be displayed.
  

Configuration

Network setting

Click “Network setting”, you’ll see the following:
1. Communication types
The default type will be Wi-Fi. Other options include: 4G / Ethernet.
2. Wi-Fi name
Select the Wi-Fi or enter the Wi-Fi name and enter the password.
3. Server address
The default address will be shown here. You can also enter a new address.
4. Grid type
The default Grid type will be shown here. If the default is wrong, click the dropdown button and select the right type from IT / TT / TN.

Notice:
When the configuration is complete, reconnect your smartphone to the charger’s hotspot, return to the web page, and the login page will be shown to you automatically, and login again to begin configuring the charging.

Charger setting

Click “Charger setting” to configure the charger.
1. Load balance
The function of Load Balance is ONLY available when power meter or CT is installed.
If both power meter and CT are installed, both ratio of transformation and maximum current can be set properly according to the CT specification.
If only one installed, either power meter or CT, ONLY maximum current can be set.
2. Charging mode switch
Click “mode switch” and choose the “Internet mode” or “Plug & Charge mode”. Then click “Confirm” to complete mode switching.

Charging & Operation

WARNING!
Observe the safety instructions on page 1 before using the product.
Make sure that the following requirements are met before using the charger:

• The authorized electrician has set up the electrical connection properly.
• The charger is properly configured.

Connect the charger to electric vehicle

1. Plug the charging connector to the electric car.
2. After plug-in, please check the connector is connected correctly and tightly.
3. When the connection is correctly established, the charger’s LED indicator will flash green fast, which indicates that the charger is ready for charging.

Start charging & stop charging

1. By RFID card: Put the RFID card on LCD screen to start or stop charging.
2. Plug & Play mode: After plug in connector, will begin charging, and will stop charging after plug out connector from car side.
3. By APP: Scan the QR code on the charger by APP, and follow the instruction of APP to operate.

If the car does not start charging, check that charging is activated in your car and that the connectors are properly plugged in. If charging still does not start, check what might be the cause on page 11.

Troubleshooting

Cycle
Leakage current loop abnormal| Flashing red, 500ms on, 500ms off, 5 times, 3S off, Cycle
Input terminal overtemperature| Flashing red, 500ms on, 500ms off, 6 times, 3S off, Cycle
Relay overtemperature| Flashing red, 500ms on, 500ms off, 7 times, 3S off, Cycle
Over/Under voltage fault| Solid yellow light blocks for 2S and flashing red, 500ms on, 500ms off, 1 time, 3S off, Cycle
Over/Under frequency fault| Solid yellow light blocks for 2S and flashing red, 500ms on, 500ms off, 2 times, 3S off, Cycle
Meter comm abnormal| Solid yellow light blocks for 2S and flashing red, 500ms on, 500ms off, 3 times, 3S off, Cycle
Smart meter comm abnormal| Solid yellow light blocks for 2S and flashing red, 500ms on, 500ms off, 4 times, 3S off, Cycle
CT fault| Solid yellow light blocks for 2S and flashing red, 500ms on, 500ms off, 5 times, 3S off, Cycle
Charging connector lock abnormal| Solid yellow light blocks for 2S and flashing red, 500ms on, 500ms off, 6 times, 3S off, Cycle
Charging connector current abnormal| Solid yellow light blocks for 2S and flashing red, 500ms on, 500ms off, 7 times, 3S off, Cycle

Note: If the problem occurs, please contact customer service.

PIN CODE

Documents / Resources

| ALVIS AC7000-AE-25 Smart Home Series Wallbox AC Charging Station [pdf] User Manual
AC7000-AE-25 Smart Home Series Wallbox AC Charging Station, AC7000-AE-25, Smart Home Series Wallbox AC Charging Station, Wallbox AC Charging Station, AC Charging Station, Charging Station, Station
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>