camry CR 1168 Turntable User Manual
- June 9, 2024
- camry
Table of Contents
camry CR 1168 Turntable
IMPORTANT SAFETY INSTRUCTIONS
SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ
CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different if the device is used for commercial
purposes.
- Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
- The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
- The applicable voltage is 230V, ~50Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.
- Please be cautious when using it around children. Do not let the children play with the product. Do not let children or people who do not know the device to use it without supervision.
- WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
- After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
- Never put the power cable, the plug or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc.. Never use the product in humid conditions.
- Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
- Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
- Never put the product on or close to hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
- Never use the product close to combustibles.
- Do not let the cord hang over the edge of a counter or touch hot surfaces.
- Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, and unplug the power.
- In order to provide additional protection, it is recommended to install a residue current device (RCD) in the power circuit, with a residual current rating of not more than 30 mA. Contact a professional electrician in this matter.
- Avoid getting the radio wet.
- The radio may only be wiped with a dry cloth. Do not use water or cleaning fluids.
- To save energy, if there is no audio signal from Turntable /AUX IN / USB / SD for a period of over 10 minutes, then the unit will automatically switch to Standby Mode.
- The radio should be kept in a dry room.
DESCRIPTION OF THE DEVICE
- Turntable cover
- LCD display
- Power diode
- In-built speaker
- FUNCTION button
- SLEEP/TIMER button
- Headphone port
- REC/DEL button
- MODE/CLOCK button
- PLAY/PAUSE/TUNER SCAN button
- STOP/BAND button
- SKIP DOWN button
- SKIP UP button
- AUX port
- ALBUM/PRESET DOWN button
- ALBUM/PRESET UP button
- ON/OFF switch/volume control
- 45RPM disc adaptor
- Turntable lever
- Turntable arm lock
- Plate spin speed adjustment
- Turntable arm
- Turntable needle guard
- LINE OUT jack
- FM antenna cable
- Power cord
- STANDBY button
- PRESET/ALBUM DN button
- PRESET/ALBUM UP button
- SD card port
- MUTE button
- AUTO-STOP switch
- REC/DEL button
- FM ST. button
- FUNCTION button
- MODE/CLOCK button
- PLAY/PAUSE button
- STOP/BAND button
- SKIP DOWN button
- SKIP UP button
- VOLUME UP/DOWN buttons
- USB port
- SNOOZE button
- Timer/Sleep button
SETTING THE CLOCK
Before first use, unpack everything and remove all protective materials. Unwind the FM antenna cable and power cable. Do not cover the ventilation holes, make sure that there is a gap of a few centimeters around the radio, which is required for proper ventilation.
- In standby mode, press and hold the MODE/CLOCK button (9, 36). ’12H/24H’ will start flashing on the display (2). Using the SKIP DOWN button (12, 39) and SKIP UP button (13, 40) select either the 12-hour or 24-hour mode and confirm by pressing the MODE/CLOCK button again (9, 36). The device will enter the hour editing mode.
- Using the SKIP DOWN button (12, 39) and SKIP UP button (13, 40) set the current hour and confirm by pressing the MODE/CLOCK button (9, 36). The device will enter the minute editing/ mode.
- Using the SKIP DOWN button (12, 39) and SKIP UP button (13, 40) set the current minute and confirm by pressing the MODE/CLOCK button (9, 36). TIMER
FUNCTION
FUNCTION (AUTOMATIC SHUT-OFF)
- When the device is switched on, press the SLEEP/TIMER button (6,44) the appropriate number of times to select the time after which the device is to switch off (90, 80, 70…10 minutes).
- The word ‘SLEEP’ on the display informs you that the automatic shut-off function is activated.
- After the selected time has elapsed the device will turn off and enter standby mode.
FUNCTION BUTTON (5)
Used to change the operating mode of the device
- PHON (turntable operation mode)
- AUX (external device operation mode)
- FM radio mode
- MP3 (USB memory playback mode and SD card playback mode) — Bluetooth mode
LISTENING TO THE RADIO
- Turn the device on using the ON/OFF button (17, 27) and set the radio mode using the FUNCTION button (5).
- Using the BAND button (11) set the wavelength to FM.
- Using the SKIP DOWN button (12, 39) and SKIP UP button (13, 40) tune to the desired radio frequency. Pressing and holding these buttons for approximately 1-2 seconds will automatically search for the closest frequency. After it is found the search will stop.
- When the frequency of the selected station is found, press the MODE/CLOCK button (9, 36) to save the station.
- Repeat steps 3-4 to program selected stations (maximum of 30 programs – FM, maximum of 20 programs – AM ).
- You can switch between saved programs by using the PRESET DOWN button (15) and PRESET UP button (16).
- You can set the volume by turning the volume control knob (17) or using the buttons (40) on the remote control.
- The FM antenna (24) is located on the back panel. If the reception is poor, try to move the antenna and find a spot in which the signal is strongest. The AM antenna is located inside the radio receiver. If the reception is poor, try moving the receiver to a different place or turning it in another direction to catch the strongest signal.
- The TUNER SCAN button (10) is used to automatically find and save available radio stations.
PLAYBACK OF MP3 FILES FROM USB/SD MEMORY
CAUTION:
The device may not be compatible with all of the files due to coding
differences. The device may not work with some USB/SD memories. The device
supports 8GB of USB memory and SD cards.
- Turn the player on using the ON/OFF button (17, 27). Place the USB or SD memory in the port (USB port – 42, SD port – 30)
- Select the mode using the FUNCTION button (5, 35).
- The device will read the memory and show the number of recorded tracks on the display. The device will then begin playback of the first track.
- You can pause and resume playback of the given track using the PLAY/PAUSE button (10, 37).
- You can playback the previous or next tracks using the SKIP DOWN button (12, 39) and SKIP UP button (13, 40). Pressing and holding these buttons during the playback of a track will make it rewind or fast-forward.
- You can playback the previous or next track album using the ALBUM DOWN button (15, 28) and ALBUM UP button (16, 29).
- During the playback of a track press the MODE/CLOCK button (9, 36) once to activate the repeat of one track. Pressing the MODE/CLOCK button (9, 36) again will repeat the entire content of the USB memory/SD card.
- Before removing the USB memory/SD card from the port first turn off the player, or switch it to radio mode, turntable disc playback mode (‘PHON’) or external device mode (‘AUX’).
You are able to play music files saved on a mobile telephone equipped with Bluetooth, for playback on the power socket radio.
- Turn on the device, and press the „ FUNCTION” button to select Bluetooth mode. .
- Activate the Bluetooth connection of the media playback device. The media playback device will now search for devices to which it can connect.
- The media playback device should now be receiving the device code CR 1168
- Use the media playback device to connect to the radio. To do this, select CR 1168 on the media playback device.
USING DEVICE
USING A DEVICE CONNECTED THROUGH THE AUX IN THE UNIVERSAL ENTRY PORT:
- Connect the external device to the player by the AUX IN port (14).
- Switch the player to the AUX IN mode by pressing the FUNCTION button (5).
PLAYBACK OF VINYL DISCS
Prior to the first use of the turntable, remove the turntable needle guard
(23) and untie the knot protecting the turntable arm found next to the
turntable arm lock (20).
- Release the arm lock (20) and set the device to PHON mode by using the FUNCTION button (5, 35).
- Place the disc on the turntable plate. If necessary, use the adapter (18).
- Select the plate’s rotational speed (the rotational speed depends on the type of disc) by using the switch (21).
- By using level (19) lift the turntable arm – this will activate the turning of the plate with the turntable disc. Gently slide the arm onto the track you want to listen to. Lower the needle arm using the lever (19).
- You can set the volume by turning the volume control knob (17) or using the buttons (40) on the remote control.
- To stop the playback of the disc, lift the turntable arm using the lever (19).
- After completion of the playback of the disc lift the turntable arm using the turntable lever (19). Move the arm over the lock (20) and lower it using the lever (19).
- To turn the AUTO-STOP function on or off use the AUTO-STOP switch (32).
RECORDING ONTO A USB DISC/SD CARD
-
Recording from the radio – place the USB disc/SD card in the appropriate port (42 or 30). Press the FUNCTION button (5, 35) to select the radio mode. Using the BAND button (11) set the wavelength to AM or FM. Using the SKIP DOWN button (12, 39) and SKIP UP button (13, 40) tune to the desired radio frequency. Press the REC/DEL button (8, 33). Within a few seconds, the device will read the available USB/SD memory media. Using the SKIP DOWN button (12, 39) and SKIP UP button (13, 40) select whether you want to record to the USB memory or the SD card. Confirm by pressing the REC/DEL button (8, 33) again. After a few seconds, the device will record to the selected portable memory (if only the USB memory or the SD card is connected, the first press of the REC/DEL button will activate the recording function after a few seconds). The REC icon will flash during recording. To stop recording press the STOP/BAND button (11, 38).
CAUTION: Activation of the process of recording from the radio will occur with a several-second delay. There may be interference/noise during radio recording. -
Recording from a vinyl disc – place the USB disc/SD card in the appropriate port (42 or 30). Press the FUNCTION button (5, 35) to select the ‘PHON’ mode. Place the vinyl disc on the plate and begin playback of the track you want to record by placing the turntable arm in the appropriate spot. The remaining steps are identical to that of recording from the radio.
-
Recording from an external device (AUX mode) – place the USB disc/SD card in the appropriate port (42 or 30). Press the FUNCTION button (5, 35) to select the ‘AUX’ mode. Connect the external device to the AUX IN port (14) and select the track you wish to record from the external device. The remaining steps are identical to that of recording from the radio.
DELETING TRACKS FROM A USB DISC/SD CARD
Deleting one recording – place the USB disc/SD card in the appropriate port
(42 or 30). Select the track you want to delete using the SKIP DOWN button
(12, 39) and SKIP UP button (13, 40) and begin playing back. Press and hold
the REC/DEL button (8, 33) for approximately 3 seconds.
SNOOZE FUNCTION
PRESS “SNOOZE”(43) BUTTON ON THE REMOTE CONTROL WHEN ALARM IS ACTIVE, ALARM
WILL BE SiLENT FOR AROUND 9-10 MINUTES. AFTER A 10-MINUTE SNOOZE INTERVAL, THE
ALARM WILL BE ACTIVE AGAIN. SNOOZE CAN BE USED FOR REPEATEDLY WITHIN THE
1-HOUR ALARM ACTIVE INTERVAL.
CLEANING AND MAINTENANCE
- Disconnect the device from the main power.
- The device may only be wiped with a dry cloth.
- The device should be kept in a dry room.
CAUTION: Do not use water for cleaning – this may damage the device.
TECHNICAL DATA
- Power source: 230V ~50Hz
- RMS output power: 2x 1.5W
- FM: 87,5-108 Mhz
- Bluetooth: 4.2V
To protect your environment: please separate carton boxes and plastic bags and dispose of them in corresponding waste bins. The used appliances should be delivered to the dedicated collecting points due to hazarsous components, which may affect the environment. The electrical appliance must be returned in order to reduce its reuse and utilization. If the device contains batteries they should be delivered to dedicated points separately.
Specification
- Model identifier THX-120100KDV
- Input voltage 220-240V
- Input AC frequency 50/60Hz
- Output voltage ⎓12V
- Output current 1 A
- Output power 12.010 W
- Average active efficiency 84,22%
- Efficiency at low load (10 %) 78,28%
- No-load power consumption 0,069 W
Available Product
AFTER-SALE SERVICE NOTICE
If you want to buy spare parts or make any complaints, please contact the
seller who issued the receipt directly.
Adler Sp. z o.o.
Ordona 2a, 01-237 Warsaw, Poland hereby declares that the CR 1168 device
complies with Directive 2014/53 / EU. The full text of the EU declaration of
conformity is available at the following internet address:
http://www.adler.com.pl/dane/deklaracje/.