anslut 018977 RGB Strip LED User Manual
- June 9, 2024
- anslut
Table of Contents
018977 RGB Strip LED
RGB STRIP LED
OPERATING INSTRUCTIONS
Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions)
Jula reserves the right to make changes.
For latest version of operating instructions, see
www.jula.com
JULA AB, BOX 363, SE-532 24 SKARA
2022-11-30
© Jula AB
1
2
3
4
5
SAFETY INSTRUCTIONS
Carefully read the instructions before use!
Save them for future reference.
-
FOR INDOOR USE ONLY.
-
Not suitable as room light.
-
Do not connect the string light to the supply while it is in the
packaging or wound onto a reel. -
Do not use the string light when it is covered or recessed into
a surface. -
Do not attempt to dismantle or cut the string light.
-
The electrical installation should be carried out by an
authorised electrician in compliance with national regulations. -
Do not use the product if it any part of it is damaged. Discard
the product, or have it repaired by an authorised electrician. -
Only use the supplied mains adapter. Do not dismantle the
product or attempt to modify, or repair it. -
Never cover the mains adapter – fire risk.
-
The bulbs are not replaceable.
-
Do not connect this string light to another string light.
-
The power cord for this string light is not replaceable; if
damaged discard the complete product. Do not run the
power cord over sharp edges. -
This string light must only be used together with a
transformer with the same output as the one supplied, and
must never be connected directly to the mains. -
Make sure the type plate is in good condition and legible.
-
The mains adapter is intended to supply a maximum of 3
flexible string lights RGB (9 LED bulbs per string) + 2
connection leads (3 LED bulbs per lead).
SYMBOLS
|
Read the instructions.
---|---
|
Safety class II
|
For indoor use only
C E
|
Approved in accordance with the relevant directives.
|
Recycle discarded product in accordance with local regulations.
TECHNICAL DATA
Transformer (In) 220-240 V~ 50/60 Hz
Transformer (Out) 12 V DC, 1 A
Output (LED) 3 x 2.4 W
Protection rating IP20
Life span (nominal) 25000 h
Number of on/offs 60000
Colour temperature (LED) RGB
Cord length (transformer) 150 cm
Size L 300 x W 10 x H 3 cm
DESCRIPTION
Flexible LED strips with RGB diodes and remote control. Each strip
contains nine red/green/blue changing diodes and is 30 long.
The strips are supplied together with two 90° angles for very
flexible installation. With the remote control you can dim, switch
between colours and lighting effects, and a lot more. Supplement
with add-on strip 018978 for more effects. Powered by 230/12 V
transformer (12 W).
The supplied adapter can supply up to 6 strings
The pack contains
- 3 flexible string lights RGB (9 LED bulbs per string)
- 2 connection leads
- 6 connectors
- 1 12V adapter
- 1 remote control
- 1 RGB LED control unit
- 16 optional colours
- Alternating or fixed colour
- Dimmer with two modes
ASSEMBLY
-
Fit the connectors on the ends of the strings.
BILD 1 -
Connect the strings BRG to BRG as shown in figure.
BILD 2 -
Connect the string to the adapter. Align the arrow on the
adapter connection to the arrow on the string.
BILD 3 -
Do not bend the string light at a sharper angle than shown
in the figure.
Min radius 30 mm
Max 60°
BILD 4
USE
Control the alternating colours with the remote control. The
remote control has a range of up to 7 m.
Remote control buttons
-
Dimmer (increase brightness)
-
Dimmer (reduce brightness)
-
Switch off
-
Switch on
-
Colour buttons
-
FLASH: The colours flash, each colour is shown for about 1
second. -
STROBE: The colours flash, each colour is shown for about 3
seconds. -
FADE: The colours change slowly, the full cycle takes about 18
seconds. -
SMOOTH: The colours change slowly, the full cycle takes about
9 seconds.
BILD 5
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>