ECHOMASTER EFS-AVL68 Asset Tracker with Inputs/Outputs Instruction Manual
- June 9, 2024
- Echomaster
Table of Contents
EFS-AVL68
INSTALLATION MANUAL
Thank you for purchasing the EchoMaster
EFS-AVL68
With EFS-AVL68, your mobile assets are in good hands. This 3 wire standard asset tracker will add GPS tracking and asset manager to fleet equipment, passenger vehicles, off-road vehicles and more. Please ensure you read and understand all aspects of the manual before installing or using the EchoMaster products.
WHAT’S INCLUDED:
- EFS-AVL68 Module
- Manual
. . . . . . . . . . . . .
FEATURES
- Autonomous over-the-air firmware updates
- Driver behavior detection to alert for harsh driving
- Internal Cellular and GPS antennas
- Accelerometer
- Low power conservation mode to protect your vehicle’s battery life
- 2 output triggers and 1 input
- Asset battery level monitoring
REQUIRED TOOLS
- Screwdriver set
- Wire cutters
- Wire strippers
- Terminal crimper
- Digital Multimeter
- Electrical Tape
- Soldering iron
PRIOR TO INSTALLATION
IMPORTANT: Prior to installation, please note the serial number located on the device.
Visit: ActivateMyEchoMaster.com
Click: Activate Asset Tracking
Enter your device’s information, and select your software plan. A member of M2M in Motion will be in touch to complete your setup.
EFS-AVL68
INSTALLATION GUIDE
STEP 1:
INSTALLATION PREPARATION INSTRUCTION
The EFS-AVL68 unit will need to be installed inside of the asset in an area where it will not get wet or damaged. Mount the module in a location that has a clear view of the sky with no metal objects between the device and the sky.
Note: Metallic objects between the GPS unit and the satellites will degrade the signal and reduce the overall performance.
STEP 2:
INSTALLATION
Main Power
Connect the RED wire to (+) 12 Volt constant power, or directly to the
asset’s battery.
Ignition Wire
Connect the BROWN ignition wire to a power source that has power when the
asset is turned on and running.
If the asset you are installing on does not have an ignition source available,
you can connect the BROWN ignition wire directly to the vehicle’s battery.
Note: the asset will always report in the application as it is on with no ignition state updates.
Chassis Ground
Connect the BLACK (-) Input wire to a solid chassis ground uninhibited by
paint or rust; do not use any floating grounds from the vehicle’s electrical
system. Always connect the ground wire directly to the asset’s chassis and
secure the connection with a factory bolt or aftermarket self-tapping screw.
I/O input and output function
The EFS-AVL68 has two configurable outputs that can be used to trigger an SPDT
automotive relay to trigger items like horns or light flash.
Pin Location
| Wire Color| Function
---|---|---
2| Orange|
Output number 1 (-)
4
| Red| Battery power (+12 Volts)
5| Black|
Chassis ground (-)
8
| Brown/White| Output number 2 (-)
18| Brown|
Ignition power or (+12V input)
Note: Outputs are low power and require a relay if used; if not it may result in damage to the device. The output will also need to be set up by M2M in Motion.
STEP 3:
TESTING THE EFS-AVL68
After installing the EFS-AVL68, move the asset outside and start the vehicle. Let it run for five minutes allowing time for the GPS receiver to receive a good signal from the GPS satellites.
Confirming the LED Lights
-
The EFS-AVL68 has LEDs located on the top of the module:
Flash RED at start-up
Flash GREEN when its location is received -
Log into The EM Fleet solutions website and confirm the vehicle location.
Note: The vehicle must be outside with an unobstructed view of the sky for its first location to be set in the application.
STEP 4:
ADD THE ASSET TO YOUR WEBSITE APPLICATION
1. Log in to emfleetmonitor.com
2. Click the settings gear in the upper right corner
3. Select “Vehicles” from the left menu
4. Select “Add Vehicle” from the upper right corner
5. Fill out the vehicle’s information and save
6. Select “Devices” from the left menu
7. In the list of devices, find the device you just installed. Click the “>” symbol on the right side to open that device, and assign it to the vehicle you just added.
8. Once the device has been assigned, click back to the map view to confirm that the location and status is correct for the vehicle that was just set up.
Specification Chart
Operating Voltage | 8V to 24V |
---|---|
Battery | 300mAh Li-ion polymer |
Current Capacity | 110uA sleep mode, 30mA Active |
Size | 2.55 in x 1.92 in x 1.02 in |
Band Operation | Dual band UMTS/HSDPA |
Host Protocol | AT commands, UDP |
Certifications | PTCRB |
IMPORTANT!
To access your GPS device on the
emfleetmonitor.com you must first register your
device at ActivateMyEchoMaster.com.
You will be asked for the devices serial number, and you will select your software options. A team member from our software partner M2M in Motion will reach out to once the application is received to get you started
email – support@aampglobal.com
tel – 866-931-8021
Phone –866-931-8021
E-Mail – support@aampglobal.com
Documents / Resources
|
ECHOMASTER EFS-AVL68 Asset Tracker with
Inputs/Outputs
[pdf] Instruction Manual
EFS-AVL68 Asset Tracker with Inputs Outputs, EFS-AVL68, Asset Tracker with
Inputs Outputs, Inputs Outputs
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>