ECHOMASTER CL-RPM Wiring Harness for Cargo Lighting 2015-2021 Promaster City and 2018-2021 Promaster Instruction Manual
- June 9, 2024
- Echomaster
Table of Contents
ECHOMASTER CL-RPM Wiring Harness for Cargo Lighting 2015-2021 Promaster
City and 2018-2021 Promaster
WHAT’S INCLUDED
- Vehicle Specific Wire Harness (CL-RPM)
COMPATIBLE ACCESSORIES
- LED Dome Lamp (STL40489-2)
- 1100mm Roof Bow Harness (P-HARRB1)
- 1570mm Roof Bow Harness (P-HARRB2)
- 2570mm Roof Bow Harness (P-HARRB3)
- 3470mm Roof Bow Harness (P-HARRB4)
- Adapter Harness (CL-ADP)
Note: Required when installing more than 4 lights in a vehicle
TOOLS REQUIRED
- Diagonal Cutters
- Panel Removal Tool
- Phillips #2 Drill Bit
- Drill
INSTALLATION INSTRUCTION
STEP 1
Remove the OEM cargo lamp that is located on the passenger side roof line
behind the slider door with a panel removal tool
Note: The factory light will no longer be used
STEP 2
Disconnect the OEM connector from the light and plug it into the CL-RPM
Harness
STEP 3
Install the STL40489-2 lights onto the center of each roof bow; leave the
light connector exposed
- Peel the red adhesive liners off of the STL40489-2 and stick the light in place
- Use the provided 3/4” screws to secure the light to the roof rib connectors.
STEP 4
Connect the appropriate P-HARRBx roof bow harness to each installed STL40489-2 light.
- Refer to the diagram on page 10 to confirm proper P-HARRBx for each roof bow
- Use the provided fir tree cable ties to secure the harness to the vehicle’s roof bow
- Trim off excess cable tie material after the harness is secure
STEP 5
Route all P-HARRBx roof bow harnesses alongside the OEM wire harnesses on the
passenger side roof line.
- Tuck the harnesses into place; inside vehicle cavities
STEP 6
Plug all installed P-HARRBx harnesses into the mating connectors on the CL-
RPM harness.
- Confirm all installed STL40489-2 lights are operational
STEP 1
Remove the OEM cargo lamp that is located on the passenger side roof line
behind the slider door with a panel removal tool
Note: The factory light will no longer be used
STEP 2
Disconnect the OEM connector from the light and plug it into the CL-RPM
Harness
STEP 3
Install the STL40489-2 lights onto the center of each roof bow; leave the
light connector
exposed
- Peel the red adhesive liners off of the STL40489-2 and stick the light in place
- Use the provided 3/4” screws to secure the light to the roof rib connectors.
STEP 4
Connect the appropriate P-HARRBx roof bow harness to each installed STL40489-2
light.
- Refer to the diagram on page 10 to confirm proper P-HARRBx for each roof bow
- Use the provided fir tree cable ties to secure the harness to the vehicle’s roof bow
- Trim off excess cable tie material after the harness is secure
STEP 5
Route all P-HARRBx roof bow harnesses alongside the OEM wire harnesses on the
passenger side roof line.
- Tuck the harnesses into place; inside vehicle cavities
STEP 6
Plug all installed P-HARRBx harnesses into the mating connectors on the CL-RPM
harness.
- Confirm all installed STL40489-2 lights are operational
Vehicle SIZE
Phone – 866-931-8021 (option 3)
E-Mail –
support@echomaster.fleetsolutions.
EchoMaster Fleet Solutions is a Power Brand of AAMP Global
EchoMaster.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>