SW-MOTECH HTA.11.955.11000 SLC Side Carrier Right Instructions
- June 4, 2024
- SW-MOTECH
Table of Contents
HTA.11.955.11000 SLC Side Carrier Right
Instructions
ANBAUANLEITUNG
mounting instructions
BC.HTA.11.955.20000
contains
HTA.11.955.11000, HTA.11.955.10000
BC.HTA.00.401.10100L, BC.HTA.00.401.10100R
Revision: 00 • Datum / Date: 07 – 2020
SLC side carrier
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required? e.g. ABE
certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety, SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore. BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behavior and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country: specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION : Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor/exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you.
MOUNTING : All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturer’s specifications or
replaced by parts delivered by SW- MOTECH. Secure all threads, unless
otherwise specified, with a medium-strength liquid thread locker. Torque
specifications undefined by SW-MOTECH must be obtained from the vehicle
manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation makes sure that all parts and
connections previously removed are properly replaced. Also, make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions. After the first 50 km and then
at regular intervals, check the tightening torque of all screw connections and
the proper fit of the product.
PARTS LIST
Step| No| Item No. / Descriptions3| Part| Quantity b|
N.mc
---|---|---|---|---|---
| | HTA.11.955.10000| SLC Side Carrier left| |
1| 1| HTA.11.955.901.01| Side Carrier; left| 1/1|
2| HTA.00.152.080| Side Carrier;| 3/3|
3| HTA.00.152.081| Lock Bolt| 1/1|
4| M6 x 20; DIN 6912| Hexagon Socket Screw, short| 1/1| 8
5| Mt x 20; DIN 79912| Countersunk Screw; black| 2/2| 8
| | | 2/2|
1| 6| M8 x 16; ISO 7380 0| Lionshead Screw; black| |
7| Ø 8,4; DIN 125| Washer; black| 2/2| 18
| | SLC Side Carrier right| |
| 1| HTA.11.955.10000| Side Carrier; right| 1/1|
| | HTA.11.955.902.01| Mounting parts see SLC Side Carrier left| |
Note :
a . All measurements in millimeters.
b . The second number indicates the total. quantity of the part in the
delivery.
c . No torque specifications: Use the torque defined by the vehicle
manufacturer! The standard torque in this table can be used as long as it is
within the vehicle manufacturer’s specifications. 
MOUNTING
NOTE: The following steps show the mounting of the left side carrier.
Mount the right side carrier in the same way. Attach the parts (2) to (5) to
the side carrier I I I, as shown in the drawing.
ATTENTION: Use a liquid thread locker! Tighten the screws as specified.
Remove the seat bench from the vehicle.
Remove the original screw and washer from the suspension strut. as shown in
the detailed drawing. Attach the side carrier (1) with the original screw and
washer 1060 to the vehicle, as shown in the drawing.
ATTENTION: Use a liquid thread locker! Tighten the screws (61 as specified.
Tighten the original screw (Orig.) with the manufacturer& specified torque.
Reattach the seat bench.
MOUNTINGS INSTRUCTIONS
Legend Gear Side Bag LC1 / LC2
Thank you for choosing this premium product from SW-MOTECH.
*Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. » www.sw-motech.com
Carefully follow all the directions given in the mounting instructions. Also,
pay attention to all relevant information in the vehicle manual during
assembly. Nonconformance can lead to vehicle damage or even endanger the
driver! Please keep the mounting instructions as a reference. SW-MOTECH
assumes no liability for damages caused by improper fixation and handling.
This product was developed for vehicles in their original condition.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Installed accessories can change the driving behavior
and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle
registration.
PREPARATION: Read the mounting instructions carefully and make sure that
all parts are included. Make sure that your vehicle is parked safely and
cannot fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Make sure to use only the appropriate
tools. During installation have another person help you.
FUNCTION CHECK: This is a universal product. For this reason make sure
BEFORE the first use, that the product can be fixed properly and used without
problems with your vehicle type.
ATTENTION: All components of the product must not contact any hot or moving
parts of the vehicle. All parts should also remain 5 cm away from hot parts of
the vehicle and remain clear of the exhaust stream. After mounting, make sure
there are no clearance issues while the suspension is both compressed and
extended.
ATTENTION: Before riding and at each stop (every 200 km) check the proper
fixation of the product!
After fixation also makes sure that no moving parts are obstructed and the
function of the vehicle is not hindered in any way. Lamps as taillight and
turn signals must not be limited in their function. Cables and hoses must not
rub and/or be pinched. Before starting to ride, perform a comprehensive check
of all functions.
LOADING INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving
and braking performance! Make sure weight is evenly distributed!
ATTENTION: Depending on the location of fixation, cornering and ground
clearance can be reduced by using this product! Never store pointy or sharp-
edged objects in the product, which could cause injury to persons or damage to
the vehicle/product. Use a waterproof inner bag/rain cover to protect your
luggage from moisture. Additionally protect sensitive Luggage (e.g.,
electronic equipment) from moisture with a plastic bag.
ATTENTION: Maximum load: 5 kg / 11 lbs! The maximum vehicle load
specified by the manufacturer must not be exceeded!
ATTENTION: Maximum speed with this product: 130 km/h!
PARTS LIST & CARE
CARE
Clean the product periodically or after each trip, as dust and dirt have a
worn effect and permanent stains can be prevented. Clean the product after
riding in salty conditions, to avoid damage from salt. First, remove dust and
encrustations with a soft dry brush. Remove stubborn deposits with a soft
cloth and warm soapy water. Do NOT use strong cleaning agents, rough cleaning
tools, or a high-pressure washer! Then rinse with clear water. Before re-use
dry the product for at least 24 hours in the air [not in direct sunlight). We
recommend impregnating the cotton textile surface of the product in regular
intervals or after intensive cleaning with a commercial wax impregnation (e.g.
from F011ravenl. ATTENTION: Because the textile surface material is a
natural fiber, it will experience color changes or fading when exposed to
direct sunlight for extended periods of time and by environmental factors
(e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this!
ATTENTION: Dirt on the product and vehicle has an abrasive effect and can
damage surfaces, such as the paint. Make sure that all areas of the vehicle,
which have contact with the product or parts of the product as straps, are
protected with an adhesive protection film from scratches and abrasions. SW-
MOTECH assumes no liability for paint damage and abrasions.
FIXATION
Fasten the Velcro closure of the side bag (l a/1 b). Revert the reinforced
opening of the side bag (lan b) twice completely.
Fix the shown loops with the side-mounted hook buckles. 
Tighten the straps of the hook buckle.
Secure the opening of the side bag flan b) with the shown strap.
Place the three openings of the quick release fastening system onto
the locating bolts of the mounted SLC side carrier.
Press the side bag (la/1b) slightly downward, until it properly
rests on the SLC side carrier. ATTENTION: Make sure that all three locating
bolts engage at the same time! Pay attention to the clearly audible snap sound
of the locking mechanism!
To release the side bag (la/1b)
simply press the shown slider of the locking mechanism downward.
Errors and omissions excepted. Technical. and design modifications
are subject to change.
SW-MOTECH GmbH & Co. KG Ernteweg 8/10
35282 Rauschenberg
Germany Tel. / phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
infolasw-motech.com
www.sw-motech.com
Copyright by SW-MOTECH GmbH & Co. KG
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>