EVErActive WL-600R Work Light User Manual
- June 9, 2024
- everactive
Table of Contents
EVErActive WL-600R Work Light User Manual
Product Overview
| 1 **** | Holder |
|---|---|
| 2 | Power input |
| 3,4 | Magnets |
| 5 | Charge indicator |
| 6 | Switch on |
| 7,8 | Light adjustment |
| 9 | Rotating arm |
| 10 | SMD LED |
| 11 | COB |
Specification
| Light sources | lx SMD LED 5W |
|---|
lx COB LED 10W
Light power| Max 550 Im
Operation modes| SMD LED dimmable (white)
COB LED dimmable (white)
COB LED dimmable (red)
COB LED flashing (red)
Power supply| Li-ion 3,7V 4000mAh
Charging type| Direct charging USB-C 5V
Station charging
Charging time| Approx 6h
Runtime| 100% – max 6h
Weight| 255g
Dimensions| 192 x 64 x 37mm
Waterproofness| IP 54
Material| PC, TPR, ABS, Aluminium
function| 5V DC 1A
**Symbols
** General information
The Everactive WL-600R rechargeable workshop torch has two light sources, is equipped with a clip with hook, two magnets and rotating arm for mounting. To turn on the flashlight press button located on the front of device. The torch has four operation modes: SMD LED in white, COB LED in white, COB LED in red, COB LED flashing in red. The flashlight is powered by 4000mAh Li-ion battery.
Using flashlight
Main button is used to turn on the torch and change operating modes, after going through all the light modes the torch will turn off. The function buttons are used to continuously adjust the light intensity, in flashing mode it allows you to change the flashing frequency. The torch can be used as a powerbank, the USB-A port is located on the back of the device under a rubber cap.
Charging
The device is equipped with a Li-ion battery, charging via USB-C port (charging cable is included). The torch can be also charged using the docking station from the kit. We recommend to charge the battery before first use.
Charging via USB-C port:
- Unplug the rubber cap,
- Connect the USB-C cable to a power source and plug it into the charging socket,
- The charging indicator will flash,
- When the battery is fully charged, the LEDs will light up continuously,
- Unplug the USB-C cable and plug the rubber cap.
Charging using the dock station:
- Set the docking station on a flat surface, then connect it to a power source,
- Install the torch in the docking station.
- The charging indicator will flash,
- When the battery is fully charged the LEDs will be on continuously.
- Remove the torch from the docking station and disconnect it from the power supply.
Package contents
- EverActive WL-600R, -Charging dock, -USB-C cable, -User manual.
Safety precautions
- Read user manual carefully before first use
- In case of prolonged inactivity, the device should be reacharged once every 3 months in order to maintain the battery life. Do not leave the device discharged.
- Protect the product from unsupervised use by children and ineligible persons.
- Do not disassembly, do not destroy, do not cause excessive shock and do not incinerate the device. Do not crush, protect against mechanical damage and fall. Do not place heavy objects on the unit.
- Avoid the sources of heat, flammable gases, protect against moisture and flooding.
- Do not allow foreign objects to enter the charger
- The device can heat up during the work and charging. Do not touch the heat sink. -Do not charge under pillows, blankets or on flammable surfaces.
- Do not operate device if it has beet wet or otherwise damaged. This could result in electrical shock or fire.
- Do not leave the device unattended during operation.
The product should be disposed of properly according to applicable law. At the end of life the product should be passed to the waste collection, electronic recycling point. It is not allowed to dispose the product with the regular household wastes. By proper disposal you contribute to the protection of the environment and natural resources. More on: www.everActive.pl/eco.
Warranty
Baltrade will repair or replace your device free of charge if it is proven to be defective within two years from the date of purchase. Baltrade shall not be held liable for any damage caused by misuse or not using the product in accordance with this manual. Warranty will be invalid if the device was modified in any way, disassembled, exposed to moisture, liquids, ingression of solid objects, extreme thermal or environmental conditions. If the device was proven to be defective, it will be repaired or replaced. In the event of a warranty claim, please contact the retailer from whom you purchased your device. You can also send it together with all accessories, to the address below:
Baltrade sp. z o.o. Kartuska 493 80-298 Gdansk, Poland
E-mail: support@baltrade.eu
Receipt or invoice as a proof of purchase should beprovided. This warranty does not affect and is in addition to legal (statutory) rights under applicable national laws relating to the sale of consumer products.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>