everActive UC800 Battery Charger User Manual

ever Active UC800 Battery Charger User Manual

Product Overview

1. LCD display LCD Nazaire fenster
2. Charging slots (1-8) Lade (1-8)
3. 1-4) Charging slots for 9V Lade Schacht fir 9V Giada ludomania dale 9V
4. MODE button Mod
5. SLOT button Lade  SLOT
6. DC power input DC /W

A Occupied charging slots
B Selected battery type
C Battery Voltage
D Charging Current
E Capacity
F Charging
percentage Blinking:
Continuous: fully charged

Technical data

Specifications

Supported battery types| Ni-MH: R03 AAA, R6 AA, R14 C, SC, 9V – blockLi-ion and Li-FePO4: 10340, 10440, 14500, 14650, 16340(R-CR123), 17500,17670, 18350, 18500, 18650, 20700,21700 22650, 25500, 26500, 26650maximum cell length: 76 mmNi-MH/Cd, Li-FePo4, Li-ion 6F22 / 9V battery
Termination voltage| Charge:Ni-MH: OAV/-AV (-1.48V), Li-ion: 4.2VLi-ion HV: 4 .35VLi-FePO4: 3.65V
Charge current| Ni-MH: 0.2A / 0.5A / 0.8A / 1A x8Li-ion/Li-HV/Li-FePO4: 0.2A/0.5A/0.8A x8; 1A x6; 2A x2 9V batteries: 60mA x2
Safety| microprocessor controlled, precise charging method, overcharge protection, damaged battery detection
Operating modes| charge
LCD Display| clear, vivid, large display with backlight
Buttons| 2
Operating temperature| 0-40°C
Power Supply| 110-230V AC/DC adapter: 12V DC, 3A Max (output)
Dimensions| 230 x 150 x 35 mm

General Information. Intended use.

Thank you for buying genuine everActive product. UC-800 is a smart Li-ion/Li- HV ,Ni-MH/Li-FePO4 battery charger. This product is intended to charge a wide range of rechargeable batteries including 3.0-3.3V Li-FePO4, 3.6-3.85V Li-ion, 1.2V Ni-MH and Ni-MH/Cd, Li-FePO4, Li-ion 6F22 / 9V battery. Supported battery sizes: 10340, 10440 (AAA), 14500 (AA), 14650, 16340 (R-CR123), 17500,17670, 18350, 18500, 18650, 20700, 21700, 22650, 25500, 26500 (C), 26650 and 9V batteries. UC-800 supports both unprotected and protected cells, which height does not exceed 76mm.

The charger is equipped with total of ten independent charging slots to provide the ultimate charging experience. Eight of them supports cylindrical batteries and two of them are only for 9V block type batteries. Professional LCD display shows a wide variety of information: charged capacity, voltage, charging current, status, battery type and more. The 9V slots only have an LED that shows charging status. UC-800 should be only used with the genuine or certified AC/DC adapters.

This product is in conformity with all provisions of Directive LVD 2014/35/EU, Directive EMC 2014/30/EU and it complies with relevant European Standards (EN).

• including protected 20700/21700 cells.

Package contents.

Each box contains:

• ever Active UC-800 charger,
• user’s manual,
• AC/DC adapter.

Safety instructions.

1. Read the instructions before using this charger.
2. The main socket outlet must be close to the equipment and easily accessible.
3. This appliance can be used by children from 8 years and above and people with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
4. Children must not play with the appliance. Cleaning and maintenance by the user must not be performed by children, unless they are over 8 years old and supervised.
5. Keep the appliance and its cord out of reach of children aged less than 8 years.
6. This charger is intended for use with cylindrical 3.0-3.3V Li-FePO4, 3.6-3.85V Li-ion, 1.2V Ni-MH and 9V rechargeable batteries only. Attempting to charge other types of batteries may cause personal injury, damage to the charger and batteries or lead to a fire.
7. The charger is intended for indoor use only. Exposure to any liquids or moisture can cause damage to the charger and batteries. Do not allow foreign objects to enter the charger. This could result in electrical shock or fire.
8. Disconnect the charger and its power adapter from power socket when not in use. Do not leave the charger unattended during operation.
9. Never use any extension cord or attachment not recommended by the manufacturer.
10. Do not operate the charger if it has been subjected to shock or damage. Take it to a qualified serviceman for repair.
11. Do not attempt to disassemble the charger or its power adapters as it may result in a risk of electric shock or fire.
12. Unplug the charger from power supply before attempting any cleaning. Use only a soft damp cloth. Do not use water, detergents or alcohol.
13. Do not attempt to charge batteries with visible defects or damage like rust, damaged isolation (wrapper), with dented or pierced casing as this could cause a fire.
14. Do not attempt to charge frozen cells.
15. Intended for use with original power adapters only.
16. Do not use batteries with their + (positive) and – (negative) ends (terminals) reversed.
17. Batteries can become hot during the charging process.

Power supply.

This charger should be used with original or certified AC/DC 12V adapter. When the charger is powered up, LCD display turns on.

Button controls.

SLOT-when charging more than one battery at once, switches to next occupied battery slot 1-8 with each button press. It is used to view detailed, individual charging information for each rechargeable battery. This button also is used to change the Li-ion battery type when the charging process already started. Long press the SLOT button till the battery type flashes, then short press MODE button to swath the battery type.

MODE- short press after inserting the battery changes the Li-ion battery mode. It is also used to change the charging current.

Please note that the charger will charge all the inserted lithium batteries by default as a 3.6/3.7V Li-ion. The battery type selection is always individual for one slot.

Basic operations.

Immediately after inserting batteries the charger will carry the diagnostic procedure to determine the battery type and its condition.

Depending on the battery voltage it will automatically detect Ni-MH and Li-ion batteries. When Li-ion cell is detected it is possible to manually activate the Li-FePO4 or Li-HV charging mode as described in point 6. Battery type symbol is indicated on LCD display (Ni-MH, Li-ion 3.7V, LI-ion 3.8V (HV), Li- FePO4).

When inserting next batteries into the charger, the LCD will always show the status of the last inserted cell. The user can  manually review other battery compartments by pressing SLOT button.

If no further action is taken by the user, the charger will start the charge process with default settings — with 500 mA current.

Selecting battery type and adjusting charging current.

The default battery type for lithium cells is Li-ion 3.6/3.7V.The battery type can be changed right after inserting the battery by quickly pressing „MODE” button. If the charger already started default process and you want to change it, you have to long press „SLOT” button till the battery type on the LCD starts flashing, then short press the „MODE” button to switch between desired battery type. The battery type change works only for one slot at a time.

The default charging current is 500mA. It can be either set for individual slot or for all slots occupied. If you want to change charging current on a specific slot use the „SLOT” button to select the slot and then long press „MODE” button till the current section on the LCD starts flashing, then pres quickly „MODE” button to switch to the desired charging current. After couple of seconds the new charging current will be accepted by the charger. If you want to change the charging current on all slots quickly press twice the „MODE” button till the current section on the LCD starts flashing, you will also see that the numbers of all occupied slots are shown on the LCD. Now short press the „MODE” button to change to the desired charging current.

NOTE: we recommend that batteries with a capacity of less than 1000 mAh are charged only by using max 500mA. Charging with 1000 mA current may shorten battery’s life.

Charging.

The charger has ten independent charging slots. It allows to charge different cells, sizes, capacities in different (from 1pc to 10pcs) quantity at the same time.

For the 3.2V LiFePO4 and 3.85V LI-HV batteries you need to change the battery type manually, the charger cannot detect those cells automaticly. It will charge them by default as normal 3.6/3.7V Li-ion battery. This is very important to match the selection according to the inserted lithium battery as improper selection may cause damage to the battery and poses a risk of fire.

The charge process is strictly controlled and terminated with very good precision (the termination method depends on battery type). Slots 1-8 are designed to charge cylindrical batteries and the battery type or charging current can be changed manually by the user. The two 9V battery slots are treated automatically and there is only one charging current — 60mA.

The charger has a OV cell reactivation. The charger will try to reactivate the OV cell with low current and if the voltage won’t increase on the battery within 3minutes all indicators will blink on the LCD and an “ERR” will be displayed.

NOTE: The charger shows the charged capacity — it is not the same as cell’s rated capacity, the value displayed one the charger LCD depends on the discharged state of the inserted batteries. The true capacity can be only measured in chargers with discharge function.

Product disposal.

The crossed-out wheeled-bin symbol on your product, battery, literature or packaging, reminds you that all electrical and electronic products, batteries and accumulators must be taken to separate collection at the end of their working life. This requirement applies in the European Union. Do not dispose any of these products as unsorted municipal waste. By proper disposal you contribute to the protection of the environment and natural resources. More on: www.everActive.pl/eco.

Warranty.

Baltrade will repair or replace your charger free of charge if it is proven to be defective within two years from the date of purchase. Baltrade shall not be held liable for any damage caused by misuse or not using the product in accordance with this manual. Warranty will be invalid if the charger was modified in any way, disassembled, exposed to moisture, liquids, ingression of solid objects, extreme thermal or environmental conditions, rapid changes in such conditions that result in damage to the charger’s electronics.

If the charger was proven to be defective, it will be repaired or replaced. In the event of a warranty claim, please contact the retailer from whom you purchased your charger.

You can also send it together with all accessories, to the address below:

Baltrade sp. z 0.0. Kartuska 493 80-298 Gdansk, Poland
E-mail: support@baltrade.eu

Receipt or invoice as a proof of purchase should be provided. This warranty does not affect and is in addition to legal (statutory) rights under applicable national laws relating to the sale of consumer products.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>