Milesight 5MP AI 23X PTZ Mini Bullet Plus Camera User Guide

: June 9, 2024
: Milesight

Table of Contents

5MP AI 23X PTZ Mini Bullet Plus Camera
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

5MP AI 23X PTZ Mini Bullet Plus Camera

Quick Start Guide

QUICK START GUIDE
Megapixel Network Camera for Video Surveillance

www.milesight.com

V6.1

Table of Content

1. Package Contents …………………………………………………………………………………………………………………………… 3

2. Cautions ………………………………………………………………………………………………………………………………………… 3

3. System Requirements ………………………………………………………………………………………………………………………3

4. Hardware Overview …………………………………………………………………………………………………………………………4

4.1 AI Color+ Vandal-proof Mini Bullet Network Camera …………………………………………………………………….. 4

4.2 AI IR Mini Dome Network Camera ………………………………………………………………………………………………. 5

4.3 AI Vandal-proof Mini Dome Network Camera ………………………………………………………………………………. 6

4.4 AI Weather-proof Mini Dome Network Camera …………………………………………………………………………….7

4.5 AI 3X AF Motorized Dome Network Camera ………………………………………………………………………………… 8

4.6 AI Motorized Dome Network Camera …………………………………………………………………………………………..9

4.7 AI Weather-proof Mini Bullet Network Camera ………………………………………………………………………….. 10

4.8 AI Vandal-proof Mini Bullet Network Camera …………………………………………………………………………….. 11

4.9 AI Motorized Bullet Network Camera …………………………………………………………………………………………12

4.10 AI Motorized Pro Bullet Network Camera ………………………………………………………………………………… 13

4.11 AI Motorized Pro Bullet Plus Network Camera …………………………………………………………………………..14

4.12 (Radar) AI (LPR) 4X/12X Pro Bullet Plus Network Camera ……………………………………………………………15

4.13 AI Motorized Pro Dome Network Camera ………………………………………………………………………………… 16

4.14 AI Pro Box Plus Network Camera …………………………………………………………………………………………….. 18

4.15 AI 12X/20X/23X PTZ Dome Network Camera ……………………………………………………………………………. 19

4.16 AI 12X PTZ Bullet Network Camera …………………………………………………………………………………………..20

4.17 AI 5X/20X/23X PTZ Bullet Plus Network Camera ………………………………………………………………………..21

4.18 AI 23X/30X/36X/42X Speed Dome Network Camera …………………………………………………………………. 22

4.19 AI 180° Panoramic Mini Bullet Network Camera …………………………………………………………………….. 23

4.20 AI 180° Panoramic Mini Dome Network Camera ……………………………………………………………………..24

4.21 AI 360° Panoramic Fisheye Network Camera …………………………………………………………………………..25

4.22 5G AI Motorized Pro Bullet Plus Network Camera …………………………………………………………………….. 26

4.23 5G AI 4X/12X Pro Bullet Plus Network Camera …………………………………………………………………………. 27

4.24 AIoT 12X Pro Bullet Plus Network Camera ……………………………………………………………………………….. 28

4.25 5G AIoT 4X/12X Pro Bullet Plus Network Camera ……………………………………………………………………… 29

4.26 Supplement Light AI LPR Motorized Pro Bullet Plus Network Camera …………………………………………. 30

4.27 Supplement Light AI LPR 4X Pro Bullet Plus Network Camera …………………………………………………….. 31

4.28 A01 Pole Mount & A03 External Corner Bracket ……………………………………………………………………….. 32

4.29 A43 Junction Box …………………………………………………………………………………………………………………… 33

4.30 A78 Recessed Mount ………………………………………………………………………………………………………………34

4.31 A81 & A82 Recessed Mount …………………………………………………………………………………………………….35

4.32 A83 Junction Box …………………………………………………………………………………………………………………… 36

5. Hardware Installation ……………………………………………………………………………………………………………………. 37

5.1 AI IR Mini Dome Network Camera …………………………………………………………………………………………….. 37

5.2 AI Vandal-proof Mini Dome Network Camera ……………………………………………………………………………..38

5.3 AI Weather-proof Mini Dome Network Camera …………………………………………………………………………..39

5.4 AI 3X AF Motorized Dome Network Camera ………………………………………………………………………………. 41

5.5 AI Motorized Dome Network Camera …………………………………………………………………………………………43

5.6 AI Weather-proof Mini Bullet Network Camera ………………………………………………………………………….. 45

5.7 AI (Color+) Vandal-proof Mini Bullet Network Camera ………………………………………………………………….47

1

Network Camera Quick Start Guide

5.8 AI Motorized Bullet Network Camera …………………………………………………………………………………………49 5.9 AI Motorized Pro Bullet Network Camera ………………………………………………………………………………….. 50 5.10 (5G/Radar/Supplement Light) AI (LPR) Pro Bullet Plus Camera …………………………………………………… 54 5.11 AI Motorized Pro Dome Network Camera ………………………………………………………………………………… 56 5.12 AI Pro Box Plus Network Camera …………………………………………………………………………………………….. 59 5.13 AI 12X/20X/23X PTZ Dome Network Camera ……………………………………………………………………………. 60 5.14 AI 12X PTZ Bullet Network Camera …………………………………………………………………………………………..63 5.15 AI 5X/20X/23X PTZ Bullet Plus Network Camera ………………………………………………………………………..65 5.16 AI 23X/30X/36X/42X Speed Dome Network Camera …………………………………………………………………. 67 5.17 AI 180° Panoramic Mini Bullet Network Camera …………………………………………………………………….. 69 5.18 AI 180° Panoramic Mini Dome Network Camera ……………………………………………………………………..71 5.19 AI 360° Fisheye Network Camera …………………………………………………………………………………………..73 5.20 A01 Pole Mount & A03 External Corner Bracket ……………………………………………………………………….. 76 5.21 A43 Junction Box …………………………………………………………………………………………………………………… 76 5.22 A78 Recessed Mount ………………………………………………………………………………………………………………80 5.23 A81 & A82 Recessed Mount …………………………………………………………………………………………………….84 6. Recommended method of outdoor installation ……………………………………………………………………………….. 88 7. How to do Hardware Reset ……………………………………………………………………………………………………………. 89 8. How to Connect to Alarm Interface ………………………………………………………………………………………………… 90 9. How to Connect the Water-proof Connector …………………………………………………………………………………… 91 10. Accessing the Milesight Network Camera ……………………………………………………………………………………… 92 10.1 Assigning an IP Address …………………………………………………………………………………………………………..92 10.2 Accessing from the Web Browser ……………………………………………………………………………………………. 98 10.3 Accessing from Milesight Back-end Software …………………………………………………………………………….98

2

Network Camera Quick Start Guide

Thank you for purchasing Milesight Network Camera. This Guide provides basic instructions on installing and accessing Milesight Network Camera. For more details, please refer to the User Manual.

1. Package Contents

Before installation, please verify that all the necessary items are supplied in the gift box as the package contents listed below. If any item is missing or damaged, please contact the shipper and your Milesight sales representative.

Default Optional

Items Milesight Network Camera Power Adapter Quick Start Guide Warranty Card Lens Bracket& Screw Pack

Quantity

Description

1 PC The purchased model

1 PC DC 12V (optional for part of devices) 1 PC Printed material 1 PC Printed material
If purchased If purchased

2. Cautions

Do not expose the product to rain or moisture Make sure the device is firmly fixed when mounting them on the wall or ceiling Make sure that the power supply voltage is correct before using the camera Do not use a third party power adapter Never attempt to disassemble or modify the camera

3. System Requirements

Operating System: Windows XP/Vista/7/8/10/Server 2000/Server 2008 CPU: 1.66GHz or higher RAM: 1G or higher Graphic memory: 128MB or more Internet protocol: TCP/IP (IPv4/IPv6) Web Browsers: Internet Explorer 8.0 and above version, Mozilla Firefox, Google Chrome and Safari

3

Network Camera Quick Start Guide

4. Hardware Overview 4.1 AI Color+ Vandal-proof Mini Bullet Network Camera
Junction Box Version:

Cable Out Version:

Note: Only PoE is available for power supply.

4

Network Camera Quick Start Guide

4.2 AI IR Mini Dome Network Camera

Note: 1) Error LED Indicator: Error LED Indicator is on when the device starts up or runs error; 2) Only PoE is available for power supply.

5

Network Camera Quick Start Guide

4.3 AI Vandal-proof Mini Dome Network Camera

Note: Default Version: Only PoE is available for power supply. Multi-interface Version: Both PoE and DC12V are available for power supply.

6

Network Camera Quick Start Guide

4.4 AI Weather-proof Mini Dome Network Camera
Junction Box Version:

Cable Out Version:

Note: Only PoE is available for power supply.

7

Network Camera Quick Start Guide

4.5 AI 3X AF Motorized Dome Network Camera

Note: DC 12V and PoE are available for power supply.

8

Network Camera Quick Start Guide

4.6 AI Motorized Dome Network Camera

Note: DC 12V and PoE are available for power supply.

9

Network Camera Quick Start Guide

4.7 AI Weather-proof Mini Bullet Network Camera

Note: Default Version: Only PoE is available for power supply. Multi-interface Version: Both PoE and DC12V are available for power supply.

10

Network Camera Quick Start Guide

4.8 AI Vandal-proof Mini Bullet Network Camera
Junction Box Version:

Cable Out Version:

Note: Only PoE is available for power supply.

11

Network Camera Quick Start Guide

4.9 AI Motorized Bullet Network Camera

Note: DC 12V and PoE are available for power supply.

(Multi-interface Version)

12

Network Camera Quick Start Guide

4.10 AI Motorized Pro Bullet Network Camera

Note: DC 12V and PoE are available for power supply.

13

Network Camera Quick Start Guide

4.11 AI Motorized Pro Bullet Plus Network Camera
Note: 1) DC 12V and PoE are available for power supply;

14

Network Camera Quick Start Guide

4.12 (Radar) AI (LPR) 4X/12X Pro Bullet Plus Network Camera

AI AF Motorized Pro Bullet Plus

Radar AI LPR AF Motorized Pro Bullet Plus

Note: DC 12V and PoE are available for power supply.

15

Network Camera Quick Start Guide

4.13 AI Motorized Pro Dome Network Camera

Note: DC 12V and PoE are available for power supply.

16

Network Camera Quick Start Guide

Motorized Pro Dome Network Camera multiple interface (Version C): Motorized Pro Dome Network Camera multiple interface (Version D):

Note: 1) For MS-Cxx72-xxPC/A, The default multiple interface is Version D. 2) For MS-Cxx72-FPD, The default multiple interface is Version C and the optional multiple
interface is Version D.

17

Network Camera Quick Start Guide

4.14 AI Pro Box Plus Network Camera
Note: DC 12V and PoE are available for power supply.

18

Network Camera Quick Start Guide

4.15 AI 12X/20X/23X PTZ Dome Network Camera

Note: 1) Reset Button: Press “Reset” button for 5 seconds, then the device will be restored to factory
default; 2) DC and PoE+ (802.3at) are available for power supply .

19

Network Camera Quick Start Guide

4.16 AI 12X PTZ Bullet Network Camera
Wall Mount:
Pedestal Mount:

Note: PoE+ (802.3at) is available for MS-Cxx61-xxPx.

20

Network Camera Quick Start Guide

4.17 AI 5X/20X/23X PTZ Bullet Plus Network Camera

Note: 1) Reset Button: Press “Reset” button for 5 seconds, then the device will be restored to factory default; 2) DC and PoE+ (802.3at) are available for power supply .

21

Network Camera Quick Start Guide

4.18 AI 23X/30X/36X/42X Speed Dome Network Camera

Note: 1) Only AC 24V is available for Speed Dome Network Camera power supply. AC 24V and PoE+
(802.3at) are available for PoE Speed Dome Network Camera power supply; 2) Built-in SD card slot can be seen after removing the 4 screws and open the front panel; 3) The Wiper and Rain Gauge Smart Sensor is optional for AI 30X/36X/42X Speed Dome Camera.

22

Network Camera Quick Start Guide

4.19 AI 180° Panoramic Mini Bullet Network Camera

Note: DC 12V and PoE are available for power supply.

23

Network Camera Quick Start Guide

4.20 AI 180° Panoramic Mini Dome Network Camera

Note: DC 12V and PoE are available for power supply.

24

Network Camera Quick Start Guide

4.21 AI 360° Panoramic Fisheye Network Camera

8MP Fisheye Network Camera:
8MP Fisheye Network Camera (Multi-interface Version): 12MP Fisheye Network Camera:

Note: DC 12V and PoE are available for power supply.

25

Network Camera Quick Start Guide

4.22 5G AI Motorized Pro Bullet Plus Network Camera

Note: DC 12V and PoE are available for power supply.

26

Network Camera Quick Start Guide

4.23 5G AI 4X/12X Pro Bullet Plus Network Camera

Note: DC 12V and PoE are available for power supply.

27

Network Camera Quick Start Guide

4.24 AIoT 12X Pro Bullet Plus Network Camera

Note: DC 12V and PoE are available for power supply.

28

Network Camera Quick Start Guide

4.25 5G AIoT 4X/12X Pro Bullet Plus Network Camera

Note: DC 12V and PoE are available for power supply.

29

Network Camera Quick Start Guide

4.26 Supplement Light AI LPR Motorized Pro Bullet Plus Camera

Note:

DC 12V and PoE are available for power supply.
Switching to web side to use Wiegand and Alarm Output.

30

Network Camera Quick Start Guide

4.27 Supplement Light AI LPR 4X Pro Bullet Plus Network Camera

Note: DC 12V is available for power supply (Non-PoE).

31

Network Camera Quick Start Guide

4.28 A01 Pole Mount & A03 External Corner Bracket

32

Network Camera Quick Start Guide

4.29 A43 Junction Box

33

Network Camera Quick Start Guide

4.30 A78 Recessed Mount

Note: There are black and white versions supported.

34

Network Camera Quick Start Guide

4.31 A81 & A82 Recessed Mount

Note: There are black and white versions supported.

35

Network Camera Quick Start Guide

4.32 A83 Junction Box

36

Network Camera Quick Start Guide

5. Hardware Installation
For AI series camera, please mount it in a forward-facing position for more accurate AI function.
5.1 AI IR Mini Dome Network Camera
Step1: Remove the dome cover;
Step2: Fix the camera on ceiling or wall directly or using Wall Mount (A71), then secure the screws. Connect the cables;

Step3: Loosen the clamp screw to adjust lens angle, then tighten it again;

Step4: Attach the dome cover.

37

Network Camera Quick Start Guide

5.2 AI Vandal-proof Mini Dome Network Camera
Step1: Remove the dome cover;

Step2: Fix the camera on ceiling or wall directly or using Wall Mount (A71), Adapter Plate (A73), Junction Box (A74), then secure the screws. Connect the cables;

38

Network Camera Quick Start Guide

Step3: Loosen the clamp screw to adjust lens angle, then tighten it again; Step4: Attach the dome cover.

5.3 AI Weather-proof Mini Dome Network Camera

Step1: Remove the dome cover, loosen the setscrew and take the bracket off;

39

Network Camera Quick Start Guide

Step2: Fix the bracket in the position where the camera is intended to be installed. Wall Mount (A71) is available for installation;
Step3: Connect the cables, rotate the camera to bracket and tighten the setscrew;

Step4: Loosen clamp screw and adjust shooting direction, tighten clamp screw;

40

Network Camera Quick Start Guide

Step5: Attach the dome cover.

5.4 AI 3X AF Motorized Dome Network Camera
Step1: Remove the dome cover, loosen the setscrew and take the bracket off;

Step2: Fix the bracket in the position where the camera is intended to be installed. Wall Mount (A71) is available for installation;

41

Network Camera Quick Start Guide

Step3: Loosen the shoulder screw and open the dome body. Take out the waterproof connector, pull out connector center. Place Piercing Cap on Ethernet Connector, and put cable through from large opening to small one. Finally, plug connector into Cable Entry Hole and rotate camera to bracket clockwise, then secure setscrew;

Step4: Connect the cables to respective connectors, then attach camera body to the base and secure shoulder screw;

Step5: Loosen clamp screw, then tighten it after adjusting shooting direction;

42

Network Camera Quick Start Guide

Step6: Attach the dome cover.

5.5 AI Motorized Dome Network Camera
Step 1: Remove the dome cover, loose the setscrew and take the bracket off;
Step 2: Fix the bracket in the position where the camera is intended to be installed. Wall Mount(A71) is available for installation;

43

Network Camera Quick Start Guide

Note: 1) Loosen the clamp screw and rotate the ball until you can see the SD Card slot;
2) Loosen the screws of SD Card structure and remove the cover;
3) Insert the SD Card, cover back the SD Card slot cover and fix the screws of SD Card structure.
Step 3: Connect the cables, rotate the camera to bracket and tighten the setscrew;

Step 4: Loosen the clamp screw and adjust shooting direction, tighten clamp screw;

44

Network Camera Quick Start Guide

Step 5: Attach the dome cover.
5.6 AI Weather-proof Mini Bullet Network Camera
Step1: Loosen the waterproof connector, and then remove the rubber seal and the waterproof connector;
Step2: Loosen and open the rear cover, then install a microSD/SDHC/SDXC card; Step3: Pass the Ethernet cable (or the tail wire of AI Weather-proof Mini Bullet with Multi-interface
Version) through the center of the mount bracket, cap nut, rubber seal and rear cover orderly for connection;

Step4: Install and tighten the rear cover; Step5: Tighten the plastic connector, rubber seal, and cap nut of the waterproof connector;

45

Network Camera Quick Start Guide

Step6: Put the bracket and camera together, rotate the bracket and fasten it using screws; Step7: Mount Camera to ceiling, wall or Junction Box (A63);

Step8: Adjust shooting direction and fix setscrew.

46

Network Camera Quick Start Guide

Note: 4) The upper cover of the AI Weather-proof Mini Bullet Network Camera could only be moved
forward for 5mm at most to ensure better field of view; 5) It will be much easier to remove the rubber seal with a screwdriver when tearing
down the camera.

5.7 AI (Color+) Vandal-proof Mini Bullet Network Camera

Step1: Connect the cables to the corresponding interface on the rear cover of the Junction Box.

Then fix the rear cover on the position where it is intended to be installed. The rear cover

can be fixed in the following two ways:

Fix the rear cover directly;

Fix the rear cover via a bracket;

47

Network Camera Quick Start Guide

Note: The bracket is optional, which can be applied in special scenarios that require screws of larger sizes. Step2: When the front cover is correctly fixed to the rear cover, the camera will be powered on by
contact power supply. Adjust shooting direction and rotate locking ring.

Note: Loosen the screws of SD card structure to get access to the SD card slot if you need. Fix the screws again after inserting the SD card to complete the operation.

48

Network Camera Quick Start Guide

5.8 AI Motorized Bullet Network Camera
Step1: Loosen the plastic connector, and then remove the rubber seal and cap nut of the waterproof connector;
Step2: Loosen and open the rear cover, then install a microSD/SDHC/SDXC card; Step3: Pass the Ethernet cable (or the tail wire of AI Motorized Mini Bullet with Multi-interface
Version) through the center of the mount bracket, cap nut, rubber seal and rear cover orderly for connection;
Step4: Install and tighten the rear cover; Step5: Tighten the plastic connector, rubber seal, and cap nut of the waterproof connector;

Step6: Put the bracket and camera together, rotate the bracket and fasten it using screws;

Step7: Mount Camera to ceiling, wall or Junction Box (A63);

49

Network Camera Quick Start Guide

Step8: Adjust shooting direction and fix setscrew;

Note: 1) The upper cover of the Motorized AI Motorized Mini Bullet Network Camera could only be
moved forward for 5mm at most to ensure better field of view; 2) It will be much easier to remove the rubber seal with a screwdriver when tearing
down the camera.

5.9 AI Motorized Pro Bullet Network Camera
Default Junction Box (A62): Step1: Fix a sticker on the position where the camera is intended to be installed;

50

Network Camera Quick Start Guide

Step2: Remove the tension disc on the rear cover of the Junction Box, and cut an opening on the rubber plug and get cables through the opening then fasten the rear cover to the sticker;
Step3: Install the front cover from the angle near 90°to the rear cover. Pay attention to the two “Tops”. The “Top” on the bullet shall be aligned to the “Top” on the Junction Box;

Step4: Adjust the cables length, and connect the cables to corresponding interfaces and fix the tension disc. Close the junction box and fix screws at last. Please remember to plug the small rubber plug whenever the holes on the rubber plug is not in use;

51

Network Camera Quick Start Guide

Step5: Adjust shooting direction and fix the setscrew.

Junction Box (Optional): Step1: Fix a sticker on the position where the camera is intended to be installed;

Step2: Take out the black rubber plug on the base, put the cables you need through the base and rubber plug (for more convenient and easier setup, the cables can get through from the side opening of rubber plug); Fasten the base to the sticker;

52

Network Camera Quick Start Guide

Step3: Hang the bullet via the hook on the base;
Step4: Adjust the cables to a suitable length and place, then connect the cables to the corresponding interfaces. Plug the black rubber plug back to the cable entry hole to prevent the ingress of dust or water. Buckle the cables by the black clamp on the base in case that the cables turning twisted and mussy. Whenever you don’t need to use the holes on the rubber plug, making sure that the small black plug is tightly stuffed up;
Step5: Install the Pro Bullet to the Junction Box, and pay attention to the two “Tops”. The “Top” on the Bullet shall be aligned to the “Top” on the Junction Box. Then fix the screws. At last, adjust the shooting direction and fix the setscrew.

Note: Loosen the screws of PTFE Membrane structure to get access to the SD card slot if you need. Fix the screws again after inserting the SD card to complete the operation.

53

Network Camera Quick Start Guide

5.10 (5G/Radar/Supplement Light) AI (LPR) Pro Bullet Plus Camera
Step1: Fix a sticker on the position where the camera is intended to be installed;

Step2: Remove the tension disc on the rear cover of the Junction Box, and cut an opening on the rubber plug and get cables through the opening then fasten the rear cover to the sticker;

Step3: Install the front cover from the angle near 90°to the rear cover. Pay attention to the two “Tops”. The “Top” on the bullet shall be aligned to the “Top” on the Junction Box;

54

Network Camera Quick Start Guide

Note: For 5G camera, you need to install the four 5G antennas before installing the front cover to the rear cover to attaching the camera to the bracket.
Step4: Adjust the cables length, and connect the cables to corresponding interfaces and fix the tension disc. Close the junction box and fix screws at last. Please remember to plug the small rubber plug whenever the holes on the rubber plug is not in use;

55

Network Camera Quick Start Guide

Step5: Adjust shooting direction and fix the setscrew.

Note: Loosen the screws of PTFE Membrane structure to get access to the SD card slot if you need. Fix the screws again after inserting the SD card. For 5G camera, the card slot is used to insert the SIM card. Use a screwdriver to help you insert it. Finally, install the 5G antennas to complete the operation.

5.11 AI Motorized Pro Dome Network Camera
Loosen the screws of the dome cover and take it off. Loosen the setscrew and take the bracket off. Step1: Fix the bracket on the position where the camera is intended to be installed. Wall Mount
(A72) and Junction Box (A75) are available for installation; Note: Only the new bracket is compatible with A75.

56

Network Camera Quick Start Guide

Step2: Loosen the shoulder screw and open the camera body. Remove the waterproof connector in the Cable Entry Hole, and then pass the cables through the Cable Entry Hole;

Step3: Rotate the camera unit clockwise, and then fix the camera to the bracket with the setscrew;

Step4: Put the cables through the White Rubber Ring and Black Rubber Bung successively (Place the Piercing Cap on the Ethernet Connector, and put the cables through White Rubber Ring from large opening to the small one). Combine the Ring and Bung and plug them into the Cable Entry Hole. Connect the cables to respective connectors, then attach the camera body to the base;

57

Network Camera Quick Start Guide

Step5: Loosen the clamp screw, adjust the camera lens to the desired direction(360 ° Pan and -5~75°Tilt). Tighten the clamp screw to fix the lens;
Step6: Attach the dome cover and make sure that the groove above is aligned to the one below as the picture shows, then fix the camera tightly ;

58

Network Camera Quick Start Guide

5.12 AI Pro Box Plus Network Camera
Step1: Fix the lens and the cable for Iris controlling to the Pro Box, then tighten the screw;
Step2: Connect the cables. Fix the camera on the accessory which has already been installed on the position where the camera is intended to be mounted (Milesight provides Protective Housing(A51) for installation).

Note: You can press ABF button on the back panel of camera to help focusing.

59

Network Camera Quick Start Guide

5.13 AI 12X/20X/23X PTZ Dome Network Camera
AI PTZ Dome Network Camera supports to get the cables out from the side. Loose the screw on the bottom if you need.
Check the wall or ceiling condition. Ensure that it is strong enough to avoid flaking. It should be able to bear the weight eight times heavier than the camera’s. Install with Mounting Bracket Step1: Fix the mounting bracket on the position where the camera is intended to be installed; Step2: Connect the cables. Then rotate the camera to the mounting bracket and tighten setscrew.

Install with Recessed Mount (A78) Step1: Ensure that the thickness of ceiling is less than 30mm, then drill a round hole whose
diameter is 220mm on it; Step2: Hold the camera and turn the top cover clockwise, then take it off;

60

Network Camera Quick Start Guide

Step3: Assemble the Recessed Mount, set the support up and screw the fixation plate to them. Then tightly lock camera with mounting bracket to the Recessed Mount;

Step4: Put the camera and Recessed Mount to the drilled hole. Screw it tightly to fix them in the ceiling;

Step5: Put the Recessed Mount cover on.

Install with Wall Mount (A77) or Pendant Mount (A79) Step1: Use the wall or ceiling hanging holder to mark the holes. Drill 4 holes on the wall or ceiling;

61

Network Camera Quick Start Guide

Step2: Screw the mounting bracket to the wall mount (A77) or pendant mount (A79). Screw the mounting bracket and holder, put the cables through them. Rotate the camera to the mounting bracket and tighten the setscrew;

Step3: Match the holder to the holes on the wall or ceiling, then tighten the screws.

Note: Loosen the screws of the dome cover and take it off. Then loosen the screws on the back of dome body to get access to the SD card slot if you need.

62

Network Camera Quick Start Guide

5.14 AI 12X PTZ Bullet Network Camera
Install with Junction Box (A62_Only for wall Mount Version.) Step1: Fix a sticker in the position where the camera is intended to be installed;
Step2: Unbolt the screws on the Junction Box (A62) between the front cover and rear cover and remove the front cover. Remove the tension disc on the rear cover, and cut an opening on the rubber plug and get cables through the opening then fasten the rear cover to the sticker;

63

Network Camera Quick Start Guide

Step3: Install the camera to front cover by using 4 torx screws and then reinstall the front cover from the angle near 90°to the rear cover;
Step4: Adjust the cables length, and connect the cables to corresponding interfaces and fix the tension disc. Close the junction box and fix screws at last. Please remember to plug the small rubber plug whenever the holes on the rubber plug is not in use;

Install to wall directly Fix the screws to the installed wall if you don’t use junction box.

64

Network Camera Quick Start Guide

Note: If you need to use the SD card, please remove the screw of the top cover and pull out the cover, then loosen the screws of SD card cover to get access to the SD card slot. After inserting SD card, fix the screws again.

5.15 AI 5X/20X/23X PTZ Bullet Plus Network Camera
Install with Junction Box (A62) Step1: Fix a sticker in the position where the camera is intended to be installed;

Step2: Unbolt the screws on the Junction Box(A62) between the front cover and rear cover and remove the front cover. Remove the tension disc on the rear cover, and cut an opening on the rubber plug and get cables through the opening then fasten the rear cover to the ceiling or wall;

65

Network Camera Quick Start Guide

Step3: Install the camera to front cover by using 4 torx screws and then reinstall the front cover from the angle near 90°to the rear cover;
Step4: Adjust the cables length, and connect the cables to corresponding interfaces and fix the tension disc. Close the junction box and fix screws at last. Please remember to plug the small rubber plug whenever the holes on the rubber plug is not in use.

Install to wall directly Fix the screws to the installed wall if you don’t use junction box.

66

Network Camera Quick Start Guide

Note: If you need to use the SD card, please remove the screw of the rear cover and pull out the cover to get access to the SD card slot. After inserting SD card, fix the screws again.

5.16 AI 23X/30X/36X/42X Speed Dome Network Camera
Step1: Check the wall or ceiling condition. Ensure that there is sufficient strength to avoid flaking. It should be able to bear the weight eight times larger than the camera’s;
Step2: Use the wall or ceiling hanging holder to mark the holes. Drill 4 holes on the wall or ceiling;

Step3: Put the cables through the holder. Match the holder with the screw holes of the camera

67

Network Camera Quick Start Guide

body and secure them;
Step4: Make sure that the camera body has been correctly installed to the holder, and match the holder to the holes on the wall or ceiling, then tighten up the screws.

68

Network Camera Quick Start Guide

5.17 AI 180° Panoramic Mini Bullet Network Camera
Step1: Connect the cables to the corresponding interface on the rear cover of the Junction Box. Then fix the rear cover on the position where it is intended to be installed. The rear cover can be fixed in the following two ways: Fix the rear cover directly;

Fix the rear cover via a bracket;

69

Network Camera Quick Start Guide

Note: The bracket is optional, which can be applied in special scenarios that require screws of larger sizes. Step2: When the front cover is correctly fixed to the rear cover, the camera will be powered on by
contact power supply. Adjust shooting direction and rotate locking ring.
Note: Loosen the screws of SD card structure to get access to the SD card slot if you need. Fix the screws again after inserting the SD card to complete the operation.

70

Network Camera Quick Start Guide

5.18 AI 180° Panoramic Mini Dome Network Camera
Loosen the setscrew and take the bracket off.
Note: There are two setscrews on the camera that fasten the bracket. Loose either one or both setscrews until the bracket can be taken off. Only one of the setscrews needs to be screwed while fixing. Fix the bracket on the position where the camera is intended to be installed. Wall Mount (A71) is available for installation.

Step1: Buckle the lanyard on the camera body tightly to the reserved hook on the bracket. After connecting the cables to respective connectors, twine the cables around tidily in the room on the bottom;

71

Network Camera Quick Start Guide

Step2: Rotate the camera to bracket and tighten the setscrew; Step3: Loosen clamp screw and adjust shooting direction, tighten clamp screw.

72

Network Camera Quick Start Guide

5.19 AI 360° Fisheye Network Camera
Hold the camera and turn the top cover anticlockwise, then take it off.
Install with Bracket or Wall Mount (A72) Step1: Fix bracket on ceiling or wall where the camera is intended to be installed. Then secure the
screws. Connect the cables, and rotate the camera to the bracket clockwise and tighten the setscrew;

Step2: Turn the top cover clockwise till the anchor points are aligned.

Install with Junction Box (A75). Step1: Fix the junction box in the position where the camera is intended to be installed. Secure the
bracket to the junction box. Pay attention that the two marks on the junction box and the bracket shall be aligned. Then connect the cables and rotate the camera to the bracket. Secure them;

73

Network Camera Quick Start Guide

Step2: Turn the top cover clockwise till the anchor points are aligned.
Install with Pendant Mount (A76) Step1: Use the Pendant Head to mark holes. Drill 4 holes in the ceiling;
Step2: Secure Mounting Adapter with Pendant Base. Put the cables through Pendant Base and then rotate the camera clockwise. Tighten the setscrew to fix the camera, then turn the top cover clockwise till the anchor points are aligned;

Step3: Put the cables through the pendant pipe in turn. And rotate it with the base and secure the

74

Network Camera Quick Start Guide

setscrew. Put the cables through the pendant head, and rotate it with the pipe and secure the setscrew;
Step4: Connect the cables, then fix the whole pendant and camera to the drilled holes in ceiling.

Note: Image Rotation function is not supported for the -PA model in the AI series. When installing the camera, please make sure the image is displayed in a forward-facing position after dewarping.

75

Network Camera Quick Start Guide

5.20 A01 Pole Mount & A03 External Corner Bracket
Accessories Map of A01 and A03:

Note: AI Weather-proof Mini Bullet, AI Vandal-proof Mini Bullet, AI Motorized Bullet, AI PTZ Bullet Plus, AI 180°Panoramic Mini Bullet&Dome and AI Color+ Vandal-proof Mini Bullet can be installed by A01 or A03 directly.
5.21 A43 Junction Box
Accessory A43 is equipped for Accessory A41/A77(Wall Mount) and A42/A79(Ceiling Mount) in order to bring a rather flexible and easy installation of AI Speed Dome and AI PTZ Dome Network Camera. Loosen the screws to open the front cover and rear cover, take out other parts from the box.

Install on the Wall Mount / Ceiling Mount Step 1: Rotate to open the front cover over about 75°to conveniently take off it from the box;

76

Network Camera Quick Start Guide

Step 2: Install the rear cover first;

Step 3: Take out the weather-proof connector, separate it to four parts as screw nut, rubber ring, screw bolt and O-ring;

Step 4: Install camera on wall/ceiling mount accessory, put the camera cables through then. The process would be easier if put the larger interface first;
Step 5: Put the camera cables through A43 screw nut, screw bolt and O-ring;
Step 6: Take rubber ring circle over the cables and put it into screw bolt;
Step 7: Rotate screw nut on screw bolt to tighten, then pass all the cables through the entry hole and rotate the whole weather-proof connector back on the front cover, and lock the accessory back on the front cover;

77

Network Camera Quick Start Guide

Step 8: The box supports top or bottom cable-out ways as below picture, through the top hole, or tension disc which put cables through bottom or bottom back. For tension disc, please remove it then cut an opening on the rubber plug, get cables through the opening. Please remember to plug the rubber plug whenever the holes on it are not in use;
Step 9: Carefully hold the front cover with wall/ceiling mount accessory and camera, put the front cover stick into the rear cover. The set screw will lock the body securely;

78

Network Camera Quick Start Guide

Step 10: Connect camera cables with previous cables. Manage the cables well then close the front cover and lock the screws.

Install on the Pole Mount Step 1: Rotate to open the front cover over about 75°to conveniently take off it from the box;

Step 2: Loosen the screws of the fix rings, put rings through the back of the box body;

Step 3: Fix the rings with rear cover on the pole, fasten the screws;

79

Network Camera Quick Start Guide

Step 4: The following steps are the same as it installed on the wall mount.
5.22 A78 Recessed Mount
Accessory A78 is used for AI Motorized Pro Dome Network Camera and AI PTZ Dome Network Camera installation, providing a way to blend camera in the environment. Ensure that the intended installed ceiling is suitable. The thickness of the ceiling should be less than 30mm. Then drill a round hole whose diameter is 220mm on it. Assemble the Recessed Mount. Stand up the legs of the big part, then put the small part on it and screw three screws.
Install with AI Motorized Pro Dome Network Camera Step1: Screw four copper columns to Recessed Mount, then lock mounting bracket to them. Tightly screw the Recessed Mount to the drilled hole;

80

Network Camera Quick Start Guide

Step2: Loosen the shoulder screw and open the camera body. Remove the waterproof connector in the cable entry hole. Connect the cables and pass it through the cable entry hole;

Step3: Rotate the camera to mounting bracket anticlockwise, then fix the camera with setscrew;

Step4: Put the cables through the waterproof connector, then plug the connector into the cable entry hole. Connect the cables to the respective connectors, then attach the camera body to the base;

Step5: Loosen the clamp screw, adjust the camera lens to the desired direction. Tighten the clamp screw to fix the lens;

81

Network Camera Quick Start Guide

Step6: Attach the dome cover and make sure that the groove above is aligned to the one below, then fix the camera tightly;

Step7: Put the Recessed Mount cover on.

Install with AI PTZ Dome Network Camera Step1: Hold the camera and turn the top cover anticlockwise, then take it off; Tightly lock camera with mounting bracket to the Recessed Mount;

82

Network Camera Quick Start Guide

Step2: Connect cables and put the camera with Recessed Mount to the drilled hole. Screw it tightly to fix them in the ceiling;
Step3: Put the Recessed Mount cover on.

83

Network Camera Quick Start Guide

5.23 A81 & A82 Recessed Mount
Accessory A81 is used for installing the cable out version of the AI Weather- proof Mini Dome Network Camera, efficiently making the camera blend in with the environment. Note: Only the cable out version of AI Weather-proof Mini Dome Network Camera is compatible with A81. Accessory A82 is used for installing the AI IR Mini Dome Network Camera, efficiently making the camera blend in with the environment. Ensuring that the intended installed ceiling is suitable, the thickness of the ceiling should be less than 30mm. Then drill a round hole whose diameter is 150mm. Step1: Remove the dome cover, for AI Weather-proof Mini Dome Network Camera also need to loosen the set screw and take the bracket off;

Step2: Take the Recessed Mount cover off and lock the AI IR Mini Dome to Recessed Mount, for AI Weather-proof Mini Dome Network Camera need to lock the Camera bracket to Recessed Mount;

84

Network Camera Quick Start Guide

Step3: Rotate the AI Weather-proof Mini Dome Network Camera to bracket and tighten the set screw;

Step4: Connect the cables and tightly lock the A81 or A82 to the drilled hole;

85

Network Camera Quick Start Guide

Step5: Adjust the AI IR Mini Dome Network Camera shooting direction and then attach dome cover, for AI Weather-proof Mini Dome Network Camera need to loosen clamp screw and adjust shooting direction, tighten clamp screw;

86

Network Camera Quick Start Guide

Step6: Put the Recessed Mount cover on. AI IR Mini Dome Network Camera
AI Weather-proof Mini Dome Network Camera

87

Network Camera Quick Start Guide

6. Recommended method of outdoor installation
The picture below shows an example of outdoor installation:

The devices represented by numbers in the picture are explained as follows: Lightning rod Video surge arrester Telecommunication surge arrester Power surge arrester Grounding conductor (resistance no more than 4 ohms) Steel tube protector
Here are some notes for outdoor installation 1) Never use the overhead line in open area. 2) Set the line under eave. 3) The signal line is at least 50 meters away from the high voltage. 4) Attach a lightning rod to the top of the pole on which the camera is going to be mounted. 5) Make sure that your camera is not at the top of the pole and must be installed within the
lightning rod below 45 degrees. 6) Make sure that system adopts equipotential grounding.

88

Network Camera Quick Start Guide

7. How to do Hardware Reset
Step1: Press the reset button and hold on, then power on the network camera and the IR LEDs will begin to twinkle ;
Step2: (For model -A/C/D/E) Keep pressing until the LEDs stop twinkle; (Only for model -B) Keep pressing the reset button until the IR LEDs stay always on;
Step3: Loosen the reset button, then the camera begin to reset;
Step4: It will take 1~3 minutes to complete the reset and the IP will turn into 192.168.5.190 (If the IP does not be changed into 192.168.5.190, please try again from step 1.);
Step5: Modify your local IP by Smart Tools again.

89

Network Camera Quick Start Guide

8. How to Connect to Alarm Interface
External interface of camera is as the following, you can refer to the picture to install the external alarm device:
PIN1: Alarm Output NC/NO 24V DC 1A PIN2: Alarm Output NC/NO 24V DC 1A PIN3: Alarm Input NC/NO 12V PIN4: Alarm Input NC/NO 12V

90

Network Camera Quick Start Guide

9. How to Connect the Water-proof Connector

Step1: Get the network cable through the screw nut, rubber ring and the screw bolt; Step2: Insert the rubber ring into the screw bolt; Step3: Connect the screw nut to the screw bolt; Step4: Place the O-Ring on the network port connector; Step5: Connect the RJ45 to the network port connector, tighten the screw bolt and the connector.
Note Please tightly wrapped all cable-out interface with adhesive tape at last to prevent them from water.

91

Network Camera Quick Start Guide

10.Accessing the Milesight Network Camera
The camera must be assigned an IP address to be accessible.
10.1 Assigning an IP Address
The Network Camera must be assigned an IP address to be accessible. The default IP address of Milesight Network Camera is 192.168.5.190. You can either change the IP address of the camera via Smart Tools or browser. Please connect the camera in the same LAN of your computer.
10.1.1 Assigning an IP Address by Using Smart Tools
Smart Tools is a software tool which can automatically detect multiple online Milesight network cameras in the LAN, set IP addresses, and manage firmware upgrades. It’s recommended to use when assigning IP addresses for multiple cameras. Step1: Install Smart Tools (The software could be downloaded from our website); Step2: Start Smart Tools, click the IPC Tools page, then enter the device information, such as IP
address, MAC address, Status, Port number, Netmask, and Gateway, then all related Milesight network cameras in the same network that will be displayed. Details are shown as shown below;

Step3: Select a camera or multiple cameras according to the MAC addresses;

92

Network Camera Quick Start Guide

Select single camera

Select multiple cameras

Step4: If the selected camera shows “Inactive” in the status bar, click “Activate” to set the

password when using it for the first time. You can also set the security questions when activating

the camera in case that you forget the password (You can reset the password by answering three

93

Network Camera Quick Start Guide

security questions correctly). Click `Save’ and it will show that the activation was successful. Note: 1) Password must be 8 to 32 characters long, contain at least one number and one letter. 2) You need to upgrade Smart Tools version to V2.4.0.1 or above to activate the camera.

After activation, you can change the IP address or other network values, and then click “Modify” button. Step5: Change the IP address successfully;

94

Network Camera Quick Start Guide

Step6: By double clicking the selected camera or the browser of interested camera, you can access the camera via web browser directly. The Internet Explorer window will pop up.

More usage of Smart Tools, please refer to the Smart Tools User Manuel: https://www.milesight.com/support/download#user-manual

95

Network Camera Quick Start Guide

10.1.2 Assign an IP Address via Browser
If the network segment of the computer and that of the camera are different, please follow the steps to change the IP address: Step1: Change the IP address of computer to 192.168.5.0 segment, here are two ways as below:
a. Start Control Panel Network and Internet Connection Network Connection Local Area Connection, and double click it.

b. Click “Advanced”, and then click “IP settings” “IP address” “Add”. In the pop-up window, enter an IP address that in the same segment with Milesight network camera ( e.g. 192.168.5.61, but please note that this IP address shall not conflict with the IP address on the existing network);

96

Network Camera Quick Start Guide

Step2: Start the browser. In the address bar, enter the default IP address of the camera: http://192.168.5.190.
Step3: You need to set the password first when using it for the first time. And you can also set three security questions for your device after activation. Then you can log in to the camera with the user name (admin) and a custom password. Note: 1) Password must be 8 to 32 characters long, contain at least one number and one letter. 2) You can click the “forget password” in login page to reset the password by answering three
security questions when you forget the password, if you set the security questions in advance. Step4: After login, please select “Settings” “Network” “Basic” “TCP/IP”. The Network Settings page appears (Shown as below Figure).

97

Network Camera Quick Start Guide

Step5: Change the IP address or other network values. Then click “Save” button; Step6: The change of default IP address is completed.
10.2 Accessing from the Web Browser
The camera can be used with the most standard operating systems and browsers. And the camera was upgraded to support Plugin-Free Mode. In Plugin-Free Mode, you can preview the video on the browser without plugin. Currently Plugin-Free Mode is supported in Firefox & Google Chrome & Safari & Edge browser for Windows system, MAC system, iOS system and Android system. Both H.265&H.264 video codec are supported in Plugin-Free Mode for camera, and it will play the secondary stream by default. Note: 1) For the firmware which below V4x.7.0.74, please upgrade the Network Camera to V4x.7.0.74 or above (Please upgrade the browser to the latest version). 2) For V4x.7.0.74 or above, you can enjoy Plugin-Free Mode without any configuration about the browser (Please upgrade the browser to the latest version). 3) For more details about set plugin-free mode of Milesight camera, please refer to https:// milesight.freshdesk.com/a/solutions/articles/69000643388.
10.3 Accessing from Milesight Back-end Software

10.3.1 Accessing from Milesight NVR (Network Video Recorder)

Milesight NVR Series can work with Milesight network cameras. Based on embedded Linux

operation system, Milesight NVR Series manages and stores HD video data. It owns multi-disk

management systems, front end HD device management system, HD video analysis system and

high-capacity system for video. Also, it adopts the technology of high flow capacity data network

transmitting&transmission, with multi-channel video decoding, to achieve functions like intelligent

98

Network Camera Quick Start Guide

management, safe storage, HD decoding, etc. For detailed information about how to use the Milesight NVR Series, please refer to Milesight NVR User Manual.

10.3.2 Accessing from Milesight CMS (Center Management System)
Milesight Central Management System (CMS) is a central management system for Milesight network cameras and Milesight NVR. It is an intelligent surveillance solution for users to control up to 256 devices, to remote preview and playback more conveniently. With high-efficient management performance, Milesight CMS software offers users a superior administration experience in such centralized system. Featured with friendly UI design, the intelligent video management system CMS allows users of all levels to setup and deploy solutions as easy as ABC. Moreover, E-map function provides users a smarter way to show the devices spatial distribution. The software could be downloaded from our website https://www.milesight.com/. Please install Milesight CMS; then launch the program to add the camera to the channel list. For detailed information about how to use the software, please refer to Milesight CMS User Manual.

99

Network Camera Quick Start Guide

10.3.3 Accessing from Milesight VMS Enterprise
Milesight VMS Enterprise is a professional and intelligent video management software for businesses. Together with our cameras, it can simplify and freshen up your video surveillance. With advanced C/S architecture, it fulfills your demands and expectations, with rich core functions including live view, record, E-Map, event alarm and smart analysis etc. The software could be downloaded from our website https://www.milesight.com/. Please install Milesight VMS Enterprise; then launch the program to add the camera to the channel list. For detailed information about how to use the software, please refer to Milesight VMS Enterprise User Manual.

100

Network Camera Quick Start Guide