OttLite 2702705 LED Lamp with Wireless Charging User Manual

June 9, 2024
OttLite

OttLite 2702705 LED Lamp with Wireless Charging User Manual

OttLite 2702705 LED Lamp with Wireless Charging User
Manual

CONGRATULATIONS! You’ve purchased the finest in natural lighting technology with your new OttLite® product.

WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete.

NOTE: THIS UNIT IS FULLY ASSEMBLED

  1. Remove lamp from packing, placing lamp body base (A) flat on a steady surface.
  2. Connect power adapter input (J) into connector (K) in the rear-bottom of the lamp.
  3. Plug the power adapter (L) into a standard household 120V outlet. Note: Only use with the supplied power adapter to avoid damage or fire.
  4. When lamp is first plugged in and receives power, a momentary green light (P) and beep sound will occur indicating that a proper electrical connection is made.
  5. Power switch (B) is a “touch” switch that controls ON/OFF power, the LED brightness settings and the colour mode function of the lamp.
  6. To power the main light, slightly touch the switch (B) to achieve the following: · Turn lamp “ON” to 1st brightness setting; touch the switch “once”; · for 2nd brightness setting; touch the switch “two-times”; · for 3rd brightness setting; touch the switch “three-times”; · to turn lamp “OFF”; touch the switch “four-times”.
  7. This lamp provides three colour modes. To adjust lighting colour mode slightly “press and hold” switch (B) for three seconds to switch light colour temperature mode; 5000K, 2700K, 4000K.
  8. To reposition the light, hold the lamp base (A) steady and grasp either lamp body (H) or shade (F) depending on needed adjustment.
  9. Refer to Diagram 1 and 2 for lamp maximum adjustment range. NOTE: DO NOT FORCE the shade outside the allowable adjustment range as excessive adjustment may cause damage.

REFER TO THE FOLLOWING ICON LEGEND FOR CONTROL PANEL (M) and (N), AS IT PERTAINS TO THE INSTRUCTIONS FOR VARIOUS SETTING FUNCTIONS BELOW.
CONTROL PANEL (M) IS LOCATED ON THE UNDERSIDE OF THE LAMP BASE.

OttLite 2702705 LED Lamp with Wireless Charging User Manual -
Symbol

ADJUST COLOUR CHANGING BASE MODES

  • Press “COLOUR CHANGING BASE ON/OFF BUTTON” to turn ON the color changing base. Press and hold this button for 3 seconds to turn it OFF.
  • Press “COLOUR CHANGING MODE BUTTON” to switch between 3 colour changing modes: Circulating Rainbow ­ Circulating Pastel ­ Colour Changing Fade.
  • When in Colour Changing Fade mode, the colour will change automatically. Press “COLOUR CHANGING BASE ON/OFF BUTTON” to select and hold the current colour. Press this button again to resume automatic Colour Changing Fade.

CLOCK SETTING:

  • When in Normal Mode and time is displayed, press and hold “SETTING BUTTON” to enter Setting Mode, press “SETTING BUTTON” again for next setting. The sequence of setting is: 12 HR or 24 HR Mode ­ HOUR – MINUTE
  • Press “SETTING BUTTON” to quit setting, or it will automatically quit to Normal Mode if idle.

CALENDAR SETTING:

  • Press “SETTING BUTTON” to display date. When date is displayed (i.e. 101 for January 1), press and hold the “SETTING BUTTON” to adjust the date. The sequence of setting is: YEAR ­ MONTH – DAY.
  • Press “SETTING BUTTON” to quit setting, or it will automatically quit to Normal Mode if idle.

ALARM & SNOOZE FUNCTION SETTING:

  • Three alarms can be set: A1 ­ A2 ­ A3.
  • Press “SETTING BUTTON” 2, 3, or 4 times to display A1, A2, or A3.
  • Once the desired alarm is displayed (A1, A2, or A3), press and hold the “SETTING BUTTON” to adjust the alarm time.
  • The sequence of setting is: HOUR ­ MINUTE ­ LENGTH OF SNOOZE (in minutes)
  • Press “SETTING BUTTON” to quit setting, or it will automatically quit to normal mode if idle.

TURNING ALARM ON AND OFF

  • To turn ON the alarm, Press “SETTING BUTTON” 2, 3, or 4 time to display A1, A2, or A3. Press “UP BUTTON” to turn alarm ON and OFF. When alarm is enabled, the left two — o n characters on the display will switch from ” ” to ” ” and an “Alarm Clock” icon
    will appear on the display.

  • Press “SETTING BUTTON” to quit setting, or it will automatically quit to normal mode if idle. ·

  • When the alarm sounds, press “SNOOZE BUTTON” to enter Snooze Mode and a “Zz” icon will appear on the clock display. If “SNOOZE BUTTON” is not pressed within 10 minutes, the alarm will automatically shut off.

  • Press and Hold “SNOOZE BUTTON” for 3 seconds to exit Snooze Mode. Alarm will sound at the same time the next day unless Alarm Mode is turned off.

ADJUST CLOCK DISPLAY BRIGHTNESS

  • To adjust the clock display brightness, press “SNOOZE/CLOCK DISPLAY BRIGHTNESS BUTTON”. There are 4 settings: OFF, L1, L2, L3.

WIRELESS CHARGING INSTRUCTIONS:

Wireless charging requires a Qi-certified device. To determine if your device is Qi-certified, please visit the Wireless Power Consortium website.
To wirelessly charge a device, perform the following:

  • Place the device, which supports Qi wireless charging standard, face up on the middle of the Qi wireless charging icon (R).
  • When the device is cantered on the Qi wireless charging area (R), a solid RED light (P) will come on noting charging mode active. Your device should show charging is taking place.
  • Check charge level on your device periodically to determine when device is fully charged
    NOTE: Product DOES NOT provide any indication of when device is fully charged.
    CAUTION! Device may become warm during charging. This is normal and part of the process. Charging times vary by device.

SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

  1. Turn lamp off and WAIT UNTIL LAMP HEAD (F) IS COOL before handling.
  2. The LED panel (G) might get hot after several hours of continuous use DO NOT place your hands directly on LED light panel.
  3. Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
  4. Do not alter the plug.
  5. The lamp head included with this unit cannot be replaced by the consumer.
  6. INDOOR USE ONLY.

NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.

BATTERY REPLACEMENT

  • This lamp uses a CR2032 battery. For battery replacement see diagram. Battery compartment is located on the underside of lamp base (A), and below battery compartment door (O).
  • To remove/install button cell battery: use a screwdriver to remove battery compartment door (O). Button cell battery is to be installed with the “+” or flat side facing upward.

BATTERY DISPOSAL: Battery disposal should be in compliance with local regulations pertaining to the disposal of hazardous materials. DO NOT INCINERATE.

SAFETY WARNING:

  • CAUTION: DO NOT INGEST BATTERY; CHEMICAL BURN HAZARD!
  • This lamp contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.
  • Keep new and used batteries away from children.
  • If the battery compartment does not close securely, stop using the product and keep it away from children.
  • If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

NOTE: Coin/button cell batteries are small, single cell devices having a diameter greater than their height.

CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.

CAUTION! THE LIGHT SOURCE CONTAINED IN THIS LUMINAIRE SHALL ONLY BE REPLACED BY THE MANUFACTURER OR HIS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON.

FCC PART 15
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION: To maintain compliance with the RF exposure guidelines, place the product at least 20cm from nearby persons.

IC CANADA
This device contains licence-exempt transmitter(s)/receiver that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN RSS-216/CNR-216 CAN ICES-005 (B)/NMB-005 (B)
CAUTION: Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite’s responsibility for proper function of product.

POWER ADAPTER SPECIFICATION: Input: 100-240 V~, 50/60 Hz, 0.9 A Output: 12V DC 2.5A with a Male DC Plug

Qi CHARGER SPECIFICATION: Output: up to 5 Watts depending on device

THIS LAMP CONTAINS a 5V, 2.1A USB output port (L) located on the bottom rear of lamp. USB port can charge items such as tablets, cellular phones, etc.
The “Qi” symbol is a trademark of the Wireless Power Consortium.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

OttLite User Manuals

Related Manuals