OttLite CSEQCOOZ Wireless Charging Desk Lamp User Manual
- October 30, 2023
- OttLite
Table of Contents
OttLite CSEQCOOZ Wireless Charging Desk Lamp User Manual
Wireless Charging Desk Lamp with Night Light and Digital Display
Congratulations!
You’ve purchased the finest in natural lighting technology with your new
OttLite® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and return it today by
mail.
WARNING: To prevent electric shock, make sure the lamp is not plugged in
until all steps are complete.
NOTE: TlllS UNIT IS FULLY ASSEMBLED
- Remove the lamp from the packaging and place it on a flat surface.
- Connect the power adaptor to the rear of the lamp and into a standard 120V household outlet. Note: Only use with the supplied power adapter to avoid damage or fire.
- When first plugged in the clock will start to chime, press up or down ( ) on the rear of the lamp to silence it.
- Touch button ( ) to turn the lamp on/off and adjust the brightness.
- Touching and holding the button ( ) will change the color mode.
- Touch button ( ) to turn on/off the night light and adjust the brightness.
TO SET THE CLOCK:
- On the rear of the lamp, locate and press the ” S’ button and the hour will start to flash. Use the ( ) to adjust the hour.
- Press “S” again and the minutes will start to flash. Use the ( ) to adjust the minutes.
- Pressing “S” again will allow you to change the date. Use the ( ) to adjust the date.
TO SET THE ALARM/SNOOZE
- On the rear of the lamp, locate and press the “M” button to activate Alarm mode, indicated on the screen by an icon ( ).
- Press the “S” button and the hour will start to flash. Use the ( ) to adjust the hour.
- Press “S” again and the minutes will start to flash. Use the ( ) to adjust the minutes and then the date.
- Press “S” again and the minutes for snoozing will start to flash. Use the ( ) to adjust the minutes.
- Press “S” again and the number “1” under the minutes will start to flash. Use the ( ) to change the alarm tone.
- In alarm mode use ( ) to activate the alarm and/or snooze function. If the “Alarm On” icon ( ) or 1’Snooze On” icon ( ) is visible on the display, the function is on. See the chart provided.
SNOOZE
Press the ( ) button to reactivate the snooze alarm.
Press the “S” button to turn off the snooze alarm.
CHANGING MODE
Press the ( ) button to change the temperature unit between °C and °F.
Press ( ) to change between 24-hour or 12-hour formats.
WIRELESS CHARGING
Center your device on the Qi wireless charging emblem ( ) and a red indicator
light ( ) on top of the base will come on to indicate charging. If the red
indicator light begins to flash, your device may not be centered on the
charger.
Note: The lamp does provide any indication of when the device is fully
charged.
CLOCK DISPLAY BRIGHTNESS:
Press the “Display” button located above the “S” and “M” buttons to change the
clock displays brightness level.
CAUTION! THE DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE. SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
- Turn the lamp off and WAIT UNTIL LAMP HEAD IS COOL before handling.
- The LED panel ( ) might get hot after several hours of continuous use. DO NOT place your hands directly on the LED light panel.
- Never use an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
- Do not alter the plug.
- The lamp head included in this unit cannot be replaced by the consumer.
- INDOOR USE ONLY.
NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
BATTERY REPLACEMENT
- This lamp uses a CR2032 battery. For battery replacement see diagram.
- The battery compartment (K) is located on the back of the lamp.
- To remove/install the button cell battery: use a screwdriver to remove the battery compartment door.
- The button cell battery is to be installed with the”+” or flat side facing upward.
BATTERY DISPOSAL: Battery disposal should be in compliance with local regulations pertaining to the disposal of hazardous materials. DO NOT INCINERATE.
SAFETY WARNING
CAUTION : DO NOT INGEST THE BATTERY; CHEMICAL BURN HAZARD!
- This lamp contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
NOTE: Coin/button cell batteries are small, single-cell devices having a diameter greater than their height.
CAUTION! I F THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS
DAMAGED, IT SHALL BE EXCLUSIVELY REPlACED BY THE MANUFACTURER OR ITS SERVICE
AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE
ONLY.
CAUTION! THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPlACEABLE; WHEN THE
LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPlACED.
CAUTION: Any change or modification to the product not expressly
recognized by Ottlite Technologies voids Ottlite’s responsibility for the
proper function of the product.
FCC PART 15
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operations.
FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION:
To maintain compliance with the FCC’s RF exposure guidelines, place the
product at least 20cm from nearby persons. This device contains a license-
exempt transmitter(s)/receiver that complies with Innovation, Science, and
Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
CAN RSS-216/CNR-216
- CAN ICES-005 (B)/NMB-005 (B)
- POWER ADAPTER SPECIFICATION:
- Input: AC 100-240V, 50/60 Hz, 1.2A Max
- Output: 12V DC, 2.5A with a Male DC Plug
Qi CHARGER SPECIFICATION:
Output: up to 5 Watts depending on the device THIS LAMP CONTAINS a 5V, 2,1A
USB output port (L) located on the bottom rear of the lamp. USB ports can
charge items such as tablets, cellular phones, etc. The “Qi” symbol is a
trademark of the Wireless Power Consortium.
Download PDF : OttLite CSEQCOOZ Wireless Charging Desk Lamp User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>