OttLite CS7QI00Z LED Desk Organizer Lamp with Wireless Charging Stand Instruction Manual

OttLite CS7QI00Z LED Desk Organizer Lamp with Wireless Charging Stand

Instruction Manual

Read instructions prior to use.

CONGRATULATIONS!

You’ve purchased the finest in natural lighting technology with your new OttLite® product.

PRODUCT REGISTRATION FORM

Please complete the enclosed Product Registration Form and return it today by mail, or register online by going to: OttLite.com/warranty

WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete.
NOTE: THIS UNIT IS FULLY ASSEMBLED

1. Remove lamp from packing, placing lamp body base (A) flat on a steady surface.

2. Connect power adapter input (B) into connector (C) in the rear-bottom of the lamp.

3. Plug the power adapter (D) into a standard household 120V outlet. Note: Only use with the supplied power adapter to avoid damage or fire.

4. Power switch (E) is a “touch” switch that controls ON/OFF power, the LED brightness settings and the color mode function of the lamp.

5. To power the light, slightly touch the switch (E) to achieve the following:
   • Turn lamp “ON” to 1st brightness setting; touch the switch “once”;
   • for 2nd brightness setting; touch the switch “two-times”;
   • for 3rd brightness setting; touch the switch “three-times”;
   • to turn lamp “OFF”; touch the switch “four-times”.

6.  This lamp provides three color modes. To adjust lighting color mode slightly “press and hold” switch (E) for three seconds to switch light color temperature mode; 2700°K, 4000°K, 5000°K.

7. To reposition the light, hold the lamp base (A) steady and grasp either flex-neck (F) or shade (G) depending on needed adjustment. DO NOT FORCE the shade or lamp body outside allowable adjustable range as excessive adjustment may cause damage.

WIRELESS CHARGING INSTRUCTIONS:

Wireless charging requires a Qi-certified device. To determine if your device is
Qi-certified, please visit the Wireless Power Consortium website.
To wirelessly charge a device, perform the following:

• Place the device on the stand horizontally, face-up, and flat against the middle of the Qi wireless charging icon (H). NOTE: Device will only charge when placed in the horizontal positon.
• When the device is centered on the Qi wireless charging icon (H), a solid RED light (J) will come ON noting charging mode active. NOTE: If RED light is OFF this indicates the device is not charging. Your device should show charging is taking place.
• Check charge level on your device periodically to determine when device is fully charged.

NOTE: Product DOES NOT provide any indication of when device is fully charged.
CAUTION! Device may become warm during charging. This is normal and part of the process. Charging times vary by device.
THIS LAMP CONTAINS a 5V, 2.1A USB output port (K) located on the bottom rear of lamp. USB port can charge items such as tablets, cellular phones, etc.

SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

1. Turn lamp off and WAIT UNTIL LAMP HEAD (G) IS COOL before handling.
2. The LED panel (L) might get hot after several hours of continuous use DO NOT place your hands directly on LED light panel.
3. Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by the consumer.
6. INDOOR USE ONLY.
   NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product

CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE
AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. CAUTION! THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN
THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED

FCC PART 15

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that of the receiver.
• Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION:

To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.
To maintain compliance with the IC RF exposure guidelines,place the product at least 10cm from nearby persons. Pour maintenir la conformité aux directives d’exposition RF de la FCC, placer le produit à au moins 20 cm des personnes à proximité. Pour maintenir la conformité aux directives d’exposition IC RF, placer le produit à au moins 10 cm des personnes à proximité.

IC CANADA

This device contains licence-exempt transmitter(s)/receiver that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
   CAN RSS-216/CNR-216
   CAN ICES-005 (B)/NMB-005 (B)
   CAUTION: Any change or modification to product not expressly recognized by OttLite
   Technologies voids OttLite’s responsibility for proper function of product.

POWER ADAPTER SPECIFICATION:

Input: 100-240 V~, 50/60 Hz, 0.9A
Output: 12V 2.5A with a Male DC Plug
Qi CHARGER SPECIFICATION:
Output: 5V 1A
The “Qi” symbol is a trademark of the Wireless Power Consortium. All phones with integrated wireless charging support “Qi”.

Read More About This Manual & Download PDF:

References

• OttLIte Warranty Information

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>