OttLite R34009 Rechargeable Desk Lamp with Lighted Mirror Instructions

: June 6, 2024
: OttLite

Table of Contents

PRODUCT REGISTRATION FORM
SPECIFICATIONS:
ACCESSORIES:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OttLite R34009 Rechargeable Desk Lamp with Lighted - Lamp
with

Li-ion Battery – Capacity: 1200mAh.
Output Voltage: 3.7V
NOTICE: Never disassemble by yourself. Use the authorized charger only. Exposure of battery to open flames could cause explosion. Do not expose the battery pack out of the temperature range 32°F to 113°F (0°C~45°C)
MADE IN CHINA

Rechargeable Desk Lamp with Lighted Mirror
R34009 R34819 C

CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with your new OttLite®product.

PRODUCT REGISTRATION FORM

Please complete the enclosed Product Registration Form and return it today by mail, or register online by going to: www.ottlite.com/warranty

NOTE: THIS UNIT IS FULLY ASSEMBLED

Remove lamp from packing and place on a flat, level surface.
Connect USB charging cable (A) to a USB power source such as a computer USB Port or a 5V USB adapter (not included).
Connect adaptor (B) to port (C) on back of lamp. Charging indicator (D) will illuminate to indicate the battery is charging.
Charge the lamp before first use. Lamp takes 6 hours to fully charge. The charging indicator (D) will turn off when lamp is fully charged.
PLEASE NOTE: This lamp will function while the USB charging cable is plugged into a power source OR on its own internal battery. When using on battery power and the light starts to dim, this indicates that the internal battery needs to be recharged.
The lamp has a slide switch (E) on the back to prevent the lamp from accidently turning on during transport.
To turn the lamp on, move slide switch (E) from “OFF” position to “ON” position, then touch power button (F) on top of lamp base (F). To turn the the lamp off, touch power button (F) again.
To increase the brightness level after turning the lamp on, press and hold power button (F) until desired setting is reached. To decrease brightness level, press and hold power button (F) again until desired setttng is reached.
When transporting the lamp, move the slide switch to the “OFF” position to avoid the lamp accidentially turning on and depleting the battery.
Hold lamp base (G) while adjusting the lamp to the desired position for use as a lamp or when using mirror (J).
NOTE: To avoid damaging the lamp, DO NOT force flexible neck into a sharp bend.

SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

Turn lamp off and WAIT UNTIL LAMP HEAD COOLS before handling.
The LED panel (H) might get hot after several hours of continuous use, DO NOT place your hands directly on LED light panel (H).
Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
Do not alter the plug.
The lamp head included with this unit cannot be replaced by the consumer.
INDOOR USE ONLY.
NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.

CAUTION! RISK OF FIRE. DO NOT POSITION MIRROR IN DIRECT SUNLIGHT. INDOOR USE ONLY.
CAUTION! THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.

FCC PART 15

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that of the receiver.
Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

CAUTION! Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite’s responsibility for proper function of product.
CAN ICES-005 (B)/NMB-005 (B)