OttLite CSVQC02Z-CA Merge LED Desk Lamp with Wireless Charging Instruction Manual

OttLite CSVQC02Z-CA Merge LED Desk Lamp with Wireless Charging Instruction Manual

Read instructions prior to use

CAUTION!
BATTERY SAFETY: This product contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately

CONGRATULATIONS! You’ve purchased the finest in natural lighting technology with your new Litotes® product.

WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete.

NOTE: THIS UNIT IS FULLY ASSEMBLED

1. Remove lamp from packing, placing lamp body base (A) flat on a steady surface.

2. Connect power adapter input (J) into connector (K) in the rear-bottom of the lamp.

3. Plug the power adapter (L) into a standard household 120V outlet.
   Note: Only use with the supplied power adapter to avoid damage or fire. When lamp is first plugged in and receives power, green lights (S & V) will illuminate momentarily and a beep sound will occur, indicating that a proper electrical connection is made.

4. Power switch (B) is a “touch” switch that controls ON/OFF power, the LED brightness settings and the color mode function of the lamp.

5. To power the main light, slightly touch the switch (B) to achieve the following:

   • Turn lamp “ON” to 1st brightness setting; touch the switch “once”;
   • for 2nd brightness setting; touch the switch “two-times”;
   • for 3rd brightness setting; touch the switch “three-times”;
   • to turn lamp “OFF”; touch the switch “four-times”.

6. This lamp provides three color modes. To adjust lighting colour mode slightly “press and hold” switch (B) for three seconds to switch light colour temperature mode; 5000K, 2700K, 4000K.

7. To reposition the light, hold the lamp base (A) steady and grasp either lamp body (H) or shade (F) depending on needed adjustment.

8. Refer to Diagrams 1 and 2 for lamp maximum adjustment range.
   NOTE: DO NOT FORCE the shade outside the allowable adjustment range as excessive adjustment may cause damage.

REFER TO THE FOLLOWING ICON LEGEND), AS IT PERTAINS TO THE INSTRUCTIONS FOR VARIOUS SETTING FUNCTIONS BELOW.

“SETTING BUTTON” (C) – to set time, date. and alarm.
“UP BUTTON” (D) – In setting mode, push to increase.
“DOWN BUTTON” (E) – In setting mode, push to decrease.

CLOCK SETTING:

• When in Normal Mode and time is displayed, press and hold “SETTING BUTTON” to enter Setting Mode, press “SETTING BUTTON” again for next setting. The sequence of setting is: 12 HR or 24 HR Mode, HOUR – MINUTE
• Press “SETTING BUTTON” to quit setting, or it will automatically quit to Normal Mode if idle.

CALENDAR SETTING:

• Press “SETTING BUTTON” to display date. When date is displayed (i.e. 501 for May 1), press and hold the “SETTING BUTTON” to adjust the date. The sequence of setting is: YEAR – MONTH – DAY.
• When in Normal Mode, the date can also be displayed by pressing the “UP BUTTON.” The date will automatically quit to Normal Mode if idle.
• Press “SETTING BUTTON” to quit setting, or it will automatically quit to Normal Mode if idle.

ALARM SETTING:

• Press “SETTING BUTTON” twice to display A1. Once the alarm is displayed, press and hold the “SETTING BUTTON” to adjust the alarm time.
• The sequence of setting is: HOUR – MINUTE
• Press “SETTING BUTTON” to quit setting, or it will automatically quit to normal mode if idle.

TURNING ALARM ON AND OFF

• To turn ON the alarm, Press “SETTING BUTTON” twice to display A1. Press “UP BUTTON” to turn alarm ON and OFF. When alarm is enabled, the left two characters on the display will switch from “–” to “on ” and an “Alarm Clock” icon will appear on the display.
• Press “SETTING BUTTON” to quit setting, or it will automatically quit to normal mode if idle.
• When the alarm sounds, press any of the buttons to turn off the alarm. The alarm will automatically shut off within 10 minutes if buttons are not pressed.
• Snooze feature is not provided.

ADJUST CLOCK DISPLAY BRIGHTNESS

• To adjust the clock display brightness, press “DOWN BUTTON”. There are 4 settings: OFF, L1, L2, L3.

WIRELESS CHARGING INSTRUCTIONS:

Wireless charging requires a Qi-certified device. To determine if your device is Qi-certified, please visit the Wireless Power Consortium website.

Wireless charging area (M) is for mobile phones. Wireless charging (N) can be used for earbuds.

To wirelessly charge a device, perform the following:

• Place the device face up on the middle of the wireless charging area (M) or (N).
• When the device is centered on the wireless charging areas (M) or (N), solid RED lights (S) or (V) respectively will come on noting charging mode active. Your device should show charging is taking place.
• Check charge level on your device periodically to determine when device is fully charged
  NOTE: Product DOES NOT provide any indication of when device is fully charged.

CAUTION! Device may become warm during charging. This is normal and part of the process. Charging times vary by device.

WATCH CHARGING STAND INSTRUCTIONS:

• To charge a watch, a wireless watch charger will need be provided (not included).

• Remove cover (T) and insert the watch charger cable into the slot located by watch stand (P).
  Guide the cable through so it fits inside the compartment. If the watch charger doesn’t fit securely into the watch stand, use one of the two silicone covers provided before placing into watch stand (P).

• Connect wireless watch charger with USB-A or USB-C connector into appropriate port (Q) or (R) and replace cover (T).

NOTE: Check the device periodically to determine if device is fully charged, as lamp DOES NOT give any indication of when the device is fully charged.

NOTE: USB ports (Q) and (R) are rated 5V, 1A and can be used to charge items such as smartwatches, tablets, cellular phones, etc. Only one USB port will function at a time with priority going to the first one plugged in.

SAFETY WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

1. Turn lamp off and WAIT UNTIL LAMP HEAD (F) IS COOL before handling.
2. The LED panel (G) might get hot after several hours of continuous use DO NOT place your hands directly on LED light panel.
3. Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by the consumer.
6. INDOOR USE ONLY.

NOTE : The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.

BATTERY REPLACEMENT

• This lamp uses a CR2032 battery. For battery replacement see diagram. Battery compartment is located on the underside of lamp base (A), and inside battery compartment cover (U).

• To remove/install button cell battery: use a screwdriver to remove battery compartment door (O). Button cell battery is to be installed with the “+” or flat side facing upward.
  BATTERY DISPOSAL: Battery disposal should be in compliance with local regulations pertaining to the disposal of hazardous materials. DO NOT INCINERATE.

• CAUTION: DO NOT INGEST BATTERY; CHEMICAL BURN HAZARD!

• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate. Even used batteries may cause severe injury or death.

• Call a local poison control center for treatment information.

• Non-rechargeable batteries are not to be recharged.

• Do not force discharge, recharge, disassemble, heat above 158 °F (70°C), or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.

• Ensure the batteries are installed correctly according to polarity (+ and -).

• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc or rechargeable batteries.

• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.

• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

NOTE: Coin/button cell batteries are small, single cell devices having a diameter greater than their height.

CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINARY IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.

CAUTION! THE LIGHT SOURCE CONTAINED IN THIS LUMINARY SHALL ONLY BE REPLACED BY THE MANUFACTURER OR HIS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON. FCC PART 15

FCC PART 15

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION:
To maintain compliance with the RF exposure guidelines, place the product at least 20cm from nearby persons.

IC CANADA

This device contains licence-exempt transmitter(s)/receiver that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN RSS-216/CNR-216
CAN ICES-005 (B)/NMB-005 (B)

CAUTION: Any change or modification to product not expressly recognized by Litotes Technologies voids Doolittle’s responsibility for proper function of product.

POWER ADAPTER SPECIFICATION:
Input : 100-240 V~, 50/60 Hz, 0.9 A
Output: 12V DC 2.5A with a Male DC Plug

Qi CHARGER SPECIFICATION:
Output of Wireless Charging Area (M) for Mobile Phones: up to 5 Watts depending on device
Output of Wireless Charging Area (N) for Earbuds: up to 4 Watts depending on device

The “Qi” symbol is a trademark of the Wireless Power Consortium.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>