Xuanyuanxing T90 Wifi Device User Manual
- June 2, 2024
- Xuanyuanxing
Table of Contents
Xuanyuanxing T90 Wifi Device
Specifications
- Model: [Insert Model Number]
- Compliance: FCC Approved
- RF Exposure Limit: 20cm minimum distance between radiator and body
Installation
- Ensure the device is connected to a power source.
- Consult the dealer or a radio/TV technician for assistance if needed.
- Do not co-locate this transmitter with any other antenna or transmitter.
RF Exposure Guidelines
For compliance with FCC radiation exposure limits:
- Install and operate the equipment with a minimum distance of 20cm between the radiator and your body.
FAQ :
Q: What should I do if I encounter issues with RF exposure?
A: If you experience any concerns regarding RF exposure, ensure that the
device is operated in accordance with the minimum distance requirements
specified in the manual. If problems persist, contact customer support for
further assistance.
Equipment Description
- when downloading the app, all the rights should be opened.
- Before configuring the network for the new camera, please restore the factory settings.
- Before setting the camera, please plug in and turn it on, and set it within the range close to the router with strong Wift signal. (The wifi hand only supports 24HZ )
Indicator Status
Prompt tone Description
APP download and registration
-
Please search “star eye” in the mobile app store to download the app, or scan the QR code to select the corresponding system of the mobile phone to download.
-
Enter your email address, next tap “Verification” button, next go to your email to get the code and input it for verification.
NOTE: Verify code email may be classified as spam by the mallbox, please check out the spam box, Please allow all tips when you launch the app for the first time. Otherwise the App may not work correctly.
Add your camera (AP mode)
-
Launch your app, and tap “+” button to add your camera.
-
Tap “AP mode” button.
-
Select the corresponding camera type.
-
Confirm that the status of the indicator light is blue light off, red light flashing, next tap “Next step” button.
-
Tap “Start configure wifl” button, then connect to WiFi name starting with “AYS-xxx” or “ХУХ-ких” which is your camera hotspot. Then you can return back to App page, next you add camera successfully: After the connection is done, return to the App.
NOTE: If you
use Android systom, a warning window may pop up saying “internet unanilable”
Ignore the message and keep on current bettork connection, ll you use 105
system, p warning window may pop up saying “Unsecured Internet” tenorg the
message and keep on curtant networe connection. -
Please click the “Configure wifi” button to enter the next step.
-
Select 2.4GHz WiFI network and input password, next tap “Next step* button.
-
click the “Join” button to enter the device configuration network, and jump to the home page after the network configuration is done.
QR Code Conne
Poweron the device, then press and hold the reset key to reset the device,
Please connect your phone to a 2.4GHE WiFi network firstly before you pair the
camera.
-
Tap “+* button.
-
Select “OR code connection”.
-
Select the corresponding camera type.
-
Next tap “Confirm that the red light is flashing”, next to “Next step” button.
-
Select 2.4GHz WiFi network and input password, next tap “Next step” button. It’s important to know that your phone must be connected to the same WiFT network as the camera during setup.
-
The camera maintains a suitable distance to scan the code to connect and wait for the prompt After four beeps, the connection is completed successfully.
Share device
Your friend has to download the “Star Eye”App, then launch the app with an
email. You open your App and tap button, then tap “Share device” button, then
tap “Add friend”, then enter your friend’s registered email, then click “Add”
button, then your friend’s App will add the camera automatically.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
RF Exposure Considerations
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.