OttLite CSN8500C Extended Reach LED Desk Lamp User Manual

: June 3, 2024
: OttLite

Table of Contents

OttLite CSN8500C Extended Reach LED Desk Lamp
PRODUCT REGISTRATION FORM
SAFETY WARNING
FCC PART 15
POWER ADAPTER SPECIFICATION:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OttLite CSN8500C Extended Reach LED Desk Lamp

CONGRATULATIONS
You’ve purchased the finest in natural lighting technology with your new OttLite product.

PRODUCT REGISTRATION FORM

Please complete the enclosed Product Registration Form and return it today by mail, or register online by going to: OttLite.com/warranty

WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete.

NOTE: THIS UNIT IS FULLY ASSEMBLED

Remove lamp from packing, placing lamp body base (A) flat on a steady surface.
Connect power adapter input (B) into connector (C) in the rear-bottom of the lamp.
Plug the power adapter (D) into a standard household 120V AC outlet. Note: Only use with the supplied power adapter to avoid damage or fire.
Turn the lamp ON/OFF by using power switch (E) located at front of shade (F).
To power LED settings, slightly touch switch (E) to achieve the following:
- Turn lamp ON to 1st brightness setting; touch the switch once;
- for 2nd brightness setting; touch the switch two-times;
- for 3rd brightness setting; touch the switch three-times;
- to turn lamp OFFâtouch the switch â€œfour-times.
To reposition the light, hold the lamp base (A) steady and grasp either flex-neck (G) or shade (F) depending on needed adjustment. DO NOT FORCE the shade or lamp body outside allowable adjustable range as excessive adjustment may cause damage.

SAFETY WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

Turn lamp off and WAIT UNTIL LAMP HEAD IS COOL before handling.
The LED panel (H) might get hot after several hours of continuous use DO NOT place your hands directly on LED light panel.
Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
Do not alter the plug.
The lamp head included with this unit cannot be replaced by the consumer.
INDOOR USE ONLY.

OttLite CSN8500C Extended Reach LED Desk Lamp 1

NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
CAUTION
IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.
CAUTION
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
CAUTION: Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite’s responsibility for proper function of product.

FCC PART 15

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

CAN ICES-005 (B)/NMB-005 (B)